Freecom SilverStore

Freecom SilverStore 2-Drive NAS 1.0

Manuf (OEM/ODM): Brand? HNC-N2 LE

Country of manuf.: China

Amazon image

ASIN
B0060H7DHK (, On Amazon, On CCC)

Type: NAS enclosure

Power: 12 VDC, 4 A
Connector type: barrel

CPU1: Marvell 88F6283 (1 GHz)
FLA1: 128 MiB134,217,728 B 1,048,576 Kib 131,072 KiB 1,024 Mib 0.125 GiB  (Samsung K9F1G08U0D)
RAM1: 128 MiB134,217,728 B 1,048,576 Kib 131,072 KiB 1,024 Mib 0.125 GiB  (Samsung K4B1G1646G-BCH9)

Expansion IFs: USB 3.0, SATA
USB ports: 2
SATA ports: 2
Serial: yes, 4-pin header, CN4, (115200,8,N,1)

ETH chip1: Marvell 88F6283
ETH chip2: Marvell 88E1318
LAN speed: 1G
LAN ports: 1

Additional chips
USB 3.0 Controller IC;NEC;D720200F1;,,;1;
FAN Controller IC;ON Semiconductor;ADT7473;,,;1;

Stock bootloader: U-Boot 1.1.4 Marvell 3.5.9

Stock FW OS: Linux 2.6.31.8

TPFirmware supported: Debian

Flags: RTC w/ battery backup

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 783 additional devices
of which 0 are Freecom devices

Ethernet OUI: none specified

For a list of all currently documented Marvell chipsets with specifications, see Marvell.

General info

CPU: Marvell 88F6283 (ARMADA 300) @1GHz
Stock bootloader is locked to boot only Stock OS by checking signature.
MB has place for soldering second RAM IC

Serial

bootloader boot log

• bootloader boot log

        __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__|  ** uboot_ver:v0.0.9 **

 ** MARVELL BOARD: HNC-N2 LE 

U-Boot 1.1.4 (Nov  9 2011 - 17:49:26) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Found ADT7473, program PWM1 ... OK
Flash:  0 kB

Marvell Serial ATA Adapter
Integrated Sata device found

CPU : Marvell Feroceon (Rev 1)
Scanning partition header:

Streaming disabled 
Write allocate disabled

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 

Saving Environment to NAND...
Erasing redundant Nand... 0x000c0000 0x000c0000
Writing to redundant Nand... Erasing Nand...Writing to Nand... done

bootloader environment

• bootloader environment

Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/ram0 rootfstype=cramfs init=/etc/rc.preroot initrd=0x800000,0x1000000
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:12:29:32
ethmtu=1500
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
uboot_ver=v0.0.9
mfgtest_state=final_tested_ok
mfgmodel=HNC-N2
ethact=egiga0
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
console=console=ttyS0,115200 mtdparts=nand_mtd:0x000a0000@0x0(uboot),0x00040000@0x000a0000(param),0x00280000@0x000e0000(preroot),
0x00380000@0x00360000(uimage),0x076e0000@0x006e0000(rootfs),0x00240000@0x07dc0000(misc),128m@0x0(flash)
bootcmd_f=nand reset; nand read.e 0x800000 0x00100000 0x00199800; check_crc32 PrEr;
bootcmd=nand reset; nand read.e 0x800000 0x00100000 0x00199800; check_crc32 PrEr; nand reset; 
nand read.e 0x40000 0x00380000 0x0027d400; check_crc32 KrNl; setenv bootargs $(console) $(bootargs_root);
bootm 0x40000; bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
bootcmd=""

Environment size: 1411/131067 bytes

Bootloader

HW description and bootloader dump