AMIT CDM530AM
AMIT CDM530AM
FCC approval date: 21 July 2009
Country of manuf.: China
Type: mobile router
FCC ID: PBLCDM530AM
Power: 5 VDC, 2 A
Connector type: barrel
CPU1: Ralink RT3050 (320 MHz)
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Macronix MX29LV320DTTI-70G)
RAM1: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (EtronTech EM63A165TS-6G)
Expansion IFs: USB 2.0
USB ports: 1
Serial: yes, internal, 4-pin header, unpopulated, 3.3V TTL
WI1 chip1: Ralink RT3050
WI1 802dot11 protocols: bgn
WI1 MIMO config: 1x1:1
WI1 antenna connector: none
ETH chip1: Ralink RT3050
LAN speed: 100M
LAN ports: 1
bgn
Stock bootloader: JBoot
Stock FW OS: Linux 2.6.21
Flags: 3G capable, portable, battery
Default SSID: default (99 addl. devices)
Default IP address: 192.168.123.254
the IP 192.168.123.254 is used by 28 additional devices
of which 13 are AMIT devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 295 additional devices
of which 11 are AMIT devices
FCC ID | |
---|---|
4G Systems XSBox Move | PBLCDM530AM |
D-Link DWR-131 rev A1 | KA2WR131A1 PBLCDM530AM |
TRENDnet TEW-655BR3G | XU8TEW655BR3G PBLCDM530AM |
CPU1 brand | WI1 chip1 brand | WI1 chip2 brand | |
---|---|---|---|
AMIT CDM530AM | Ralink | Ralink | |
AMIT CDM530AM-002 | Ralink | Ralink |
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
WiFi Mobile Broadband Gateway
- Product page (Zalip)
"11340Y20EA00003A1" is silkscreened on the board in the FCC photos.
"11340Y20EA00004A1" is silkscreened on a production unit (see below pictures).
The default SSID is default.
Serial
Pinout
It's marked on the board.
Info derived from
• boot log |
---|
JBoot B252 JRecovery Version R1.2 2010/06/17 13:35 Flash MXIC-22A7 0xBF000000-0x400000 x16 ............... Starting kernel @80000000... LINUX started... THIS IS ASIC Linux version 2.6.21 (charles@uranus) (gcc version 3.4.2) #13 Thu Jul 22 11:57:06 CST 2010 The CPU feqenuce set to 320 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 10800000, status = 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00138800(1280000) CPU frequency 320.00 MHz Using 160.000 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29304k/32768k available (2389k kernel code, 3464k reserved, 551k data, 124k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro fuse init (API version 7.8) io scheduler noop registered (default) FLASH_API: MAN_ID=C2 DEV_ID=22A7 SIZE=4MB ------------------GPIO-------------------------- GPIOMODE:2df SLIC INTR ==> gpio 0 Ralink gpio driver initialized HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 254 GDMA1_MAC_ADRH -- : 0x00000000 GDMA1_MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated, mtu = 1500! GDMA1_MAC_ADRH -- : 0x0000dc91 GDMA1_MAC_ADRL -- : 0xf659bfab PROC INIT OK! TX100 AD/DA current bias: 7054 TX100 slew rate control: 0038 PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 ralink flash device: 0x400000 at 0xbf000000 Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 6 MTD partitions on "Ralink SoC physically mapped flash": 0x00000000-0x00400000 : "Whole" 0x00000000-0x00010000 : "Bootloader" 0x00010000-0x00110000 : "Kernel" 0x00110000-0x003a0000 : "RootFS" 0x003a0000-0x003f0000 : "UI" 0x003f0000-0x00400000 : "Config" block2mtd: version $Revision: 1.1.1.1 $ usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver u32 classifier Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (256 buckets, 2048 max) Register conntrack protocol helper for ESP... GRE over IPv4 tunneling driver Init IP_nat_proto_esp register. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 124k freed Algorithmics/MIPS FPU Emulator v1.5 Ralink HotFix switch register base addr to 0xb0180000 write offset 0x500, value 0x31a65 write offset 0x500, value 0x31b23 Inter-| Receive phy_tx_ring = 0x01c70000, tx_ring = 0xa1c70000, size: 16 bytes phy_rx_ring = 0x01c71000, rx_ring = 0xa1c71000, size: 16 bytes | Transmit fRT305x_ESW: Link Status Changed ace |bytes paGDMA1_FWD_CFG = 710000 ckets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed eth2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gre0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 dwc_otg: version 2.72a 24-JUN-2008 DWC_otg: Core Release: 2.66a DWC_otg: Periodic Transfer Interrupt Enhancement - disabled DWC_otg: Multiprocessor Interrupt Enhancement - disabled DWC_otg: Using DMA mode DWC_otg: Device using Buffer DMA mode dwc_otg lm0: DWC OTG Controller dwc_otg lm0: new USB bus registered, assigned bus number 1 dwc_otg lm0: irq 18, io mem 0x00000000 DWC_otg: Init: Port Power? op_state=1 DWC_otg: Init: Power Port (0) usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Load RT2880 Timer Module(Wdg/Soft) flash_open: flash_fd=3 Mount D Section. timezone:0 dsttime:0 flash_open: flash_fd=9 Fri Jan 1 00:00:00 UTC 2010 timezone:0 dsttime:0 switch reg write offset=14, value=405555 switch reg write offset=50, value=2001 switch reg write offset=98, value=7f3f switch reg write offset=e4, value=3f switch reg write offset=40, value=1002 switch reg write offset=44, value=1001 switch reg write offset=48, value=1001 switch reg write offset=70, value=ffff417e ----1--0-- Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[4].reg[0] = 3900 Single Ethernet Port Configured as LAN eth2.2: Setting MAC address to 00 50 18 5f 5d 0c. device eth2 entered promiscuous mode VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode. ifconfig eth2.2 hw ether 0050185F5D0C eth2.2: dev_set_promiscuity(master, 1) device eth2.2 entered promiscuous mode br0: port 1(eth2.2) entering learning state br0: topology change detected, propagating br0: port 1(eth2.2) entering forwarding state rt2860v2_ap: module license 'unspecified' taints kernel. Jack 2860 version : 2.0.0.0 (Jul 22 2010) --- pAd = c0448000, size = 414016 --- <-- RTMPAllocAdapterBlock, Status=0 Length of MAC:6 mac:0:50:18:5f:5d:c: ---- RX DESC a1f6d000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 2a:55:44:e4:05:1a:cb:eb:01:93:83:88:b2:c3:4f:8f: 50:b2:65:62:c1:a3:cb:f9:52:8e:b0:b1:79:c9:b6:97: 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff 00 00 00 01 Main bssid = 00:50:18:5f:5d:0c The UUID Hex string is:2880288028801880a8800050185f5d0c The UUID ASCII string is:28802880-2880-1880-a880-0050185f5d0c! <---- RTMPInitialize, Status=0 0x1300 = 00064380 device ra0 entered promiscuous mode br0: port 2(ra0) entering learning state br0: topology change detected, propagating br0: port 2(ra0) entering forwarding state --> This is a single-ether router. ->WAN_TYPE is 16 ---- NAT START ---- /var/nat-draft.uyg start ok udhcpd (v0.9.9-pre) started Unable to open /var/run/udhcpd.leases for reading timezone:0 dsttime:0 ============= AMIT UPNP Start ============= WAN_IF=eth2.2,LAN_IF=br0 # |
cat /etc/passwd
# cat passwd root:$1$$N76hdwGfg11g0KdKbtyh21:0:0:root:/root:/bin/ash
password: amittima
netstat -l
# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:8080 *:* LISTEN tcp 0 0 *:http *:* LISTEN tcp 0 0 192.168.123.254:2300 *:* LISTEN udp 0 0 *:9 *:* udp 0 0 *:67 *:* udp 0 0 *:1900 *:* Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path
ps aux
# ps aux PID Uid VmSize Stat Command 1 root 332 S init 2 root SWN [ksoftirqd/0] 3 root SW< [events/0] 4 root SW< [khelper] 5 root SW< [kthread] 26 root SW< [kblockd/0] 29 root SW< [khubd] 41 root SW< [kswapd0] 42 root SW [pdflush] 43 root SW [pdflush] 44 root SW< [aio/0] 643 root SW [mtdblockd] 695 root SW< [dwc_otg] 713 root 256 S syslogd 716 root 256 S klogd -f 728 root 288 S csmanuds -p /var/run/csman.pid 786 root 132 S ated br0 799 root SW [rtmpWscHandle] 1470 root 228 S udhcpd /etc/udhcpd.conf 1490 root 412 S AmitUPnP eth2.2 br0 1499 root 308 S httpd 1501 root 264 S AGPServer 1503 root 332 S commander 1506 root 484 S -ash 1517 root 412 S AmitUPnP eth2.2 br0 1518 root 412 S AmitUPnP eth2.2 br0 1519 root 412 S AmitUPnP eth2.2 br0 1528 root 172 S telnetd -b 192.168.123.254 7950 root 352 R ps aux
cat /proc/mtd
# cat mtd dev: size erasesize name mtd0: 00400000 00010000 "Whole" mtd1: 00010000 00010000 "Bootloader" mtd2: 00100000 00010000 "Kernel" mtd3: 00290000 00010000 "RootFS" mtd4: 00050000 00010000 "UI" mtd5: 00010000 00002000 "Config"
cat /proc/modules
# cat modules rt2860v2_ap 1061088 1 - Live 0xc059f000 (P) xt_time 3200 0 - Live 0xc040a000 rt_timer 2432 0 - Live 0xc0408000 dwc_otg 103824 0 - Live 0xc042d000 lm 3520 1 dwc_otg,[permanent], Live 0xc0406000
cat /proc/cmdline
# cat cmdline console=ttyS1,57600n8 root=/dev/mtdblock3
cat /proc/meminfo
# cat meminfo MemTotal: 29428 kB MemFree: 16032 kB Buffers: 1368 kB Cached: 4560 kB SwapCached: 0 kB Active: 2640 kB Inactive: 4068 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 828 kB Mapped: 764 kB Slab: 4672 kB SReclaimable: 596 kB SUnreclaim: 4076 kB PageTables: 204 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 14712 kB Committed_AS: 3548 kB VmallocTotal: 1048404 kB VmallocUsed: 5696 kB VmallocChunk: 1041604 kB