ASUS DSL-N14U

ASUS DSL-N14U (B1)
Availability: now

Manuf (OEM/ODM): SGE

(Est.) release date: February 2015
Country of manuf.: China

Amazon image

ASINs
B00KQF9KZU (, On Amazon, On CCC)
B00T7EG932 (, On Amazon, On CCC)
B00J8LW6CM (, On Amazon, On CCC)

Type: wireless router, dsl modem

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: Ralink RT63365E (500 MHz)
FLA1: 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (Macronix MX25L12835EMI-10G)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (EtronTech EM6AB160TSD-5G)

Expansion IFs: USB 2.0
USB ports: 1

WI1 chip1: Ralink RT5392L
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: RP-SMA

ETH chip1: Ralink RT63365E
Switch: Ralink RT63365E
LAN speed: 100M
LAN ports: 4

bgn

Additional chips
xDSL AFE;Ralink;RT63087N;;1;

Stock bootloader: CFE

Stock FW OS: Linux 2.6.22.15

Flags: ADSL2+, AiCloud support

802dot11 OUI: none specified

For a list of all currently documented Ralink chipsets with specifications, see Ralink.

---

Wireless-N300 ADSL Modem Router

Product page

ASUS's firmware seems to indicate this device is Ralink/TrendChip based..

See also: ASUS DSL series and ASUS

Forum threads

• On HWupgrade

Spec. aggregators

• On SpeedGuide.net
• On HWupgrade

Firmware

Asus DSL-N14U downloads

FW v1.1.2.3_805

FW SRC v1.1.2.3_805

Specifications

per ASUS's product page

• Memory: 16MB Flash, 64MB (DDR2) RAM
• Antenna: 2x Detachable 2dBi antenna
• Ports: 4x RJ45 10/100 BaseT for LAN, 1x RJ11 for xDSL
• USB: 1x USB 2.0 ports
• Power Adapter: AC Input: 100~240V (50/60Hz), DC Output: 12V/1A
• Dimensions (W x H x D): 123 mm x 35 mm x 190 mm
• Weight: 314 g0.314 kg <br />11.075 oz <br />0.692 lbs <br />

Serial

• Full boot • >>

RT63365 at Mon Feb 13 20:40:38 CST 2012 Memory size 64MB flash base: b0000000 Found SPI Flash 16MiB MX25L12805D at 0xb0000000Bootloader version: 3.1 Search PHY addr and found PHY addr=1 Press reset button to boot command mode. Press any key in 1 secs to enter boot command mode. . checkimage...ok Decompress to 80020000 free_mem_ptr=80600000 free_mem_ptr_end=80780000 Uncompressing [LZMA] ... done. Linux version 2.6.22.15 (root@localhost) (gcc version 4.3.4 (GCC) ) #1 SMP Sat Nov 30 02:26:27 CST 2019 ISPRAM0: PA=002a8000,Size=00008000,enabled Enable SRAM=1c000001 Ralink RT63365 SOC prom init CPU revision is: 00019555 Determined physical RAM map: memory: 04000000 @ 00000000 (usable) 3 available secondary CPU TC(s) Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS0 rootfstype=squashfs es=1 Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (23 instructions). Synthesized TLB load handler fastpath (37 instructions). Synthesized TLB store handler fastpath (37 instructions). Synthesized TLB modify handler fastpath (36 instructions). Cache parity protection disabled PID hash table entries: 256 (order: 8, 1024 bytes) CPU frequency 498.00 MHz Using 250.000 MHz high precision timer. console handover: boot [early0] -> real [ttyS0] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61184k/65536k available (2626k kernel code, 4296k reserved, 513k data, 160k init, 0k highmem) SLUB: Genslabs=17, HWalign=32, Order=0-1, MinObjects=4, CPUs=4, Nodes=1 Mount-cache hash table entries: 512 34K sync es set to 1. Config7: 0x80080500 FPU Affinity set after 1105 emulations Limit of 4 TCs set TLB of 64 entry pairs shared by 2 VPEs VPE 0: TC 0 1 2, VPE 1: TC 3 IPI buffer pool of 32 buffers CPU revision is: 00019555 TC 1 going on-line as CPU 1 CPU revision is: 00019555 TC 2 going on-line as CPU 2 CPU revision is: 00019555 TC 3 going on-line as CPU 3 Brought up 4 CPUs migration_cost=10000 NET: Registered protocol family 16 RT63365_pcie_init registering PCI controller with io_map_base unset PCI: Bridge: 0000:00:00.0 IO window: disabled. MEM window: 20000000-200fffff PREFETCH window: disabled. NET: Registered protocol family 8 NET: Registered protocol family 20 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 24576 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered TC3162 hardware watchdog module loaded. squashfs: version 3.0 (2006/03/15) Phillip Lougher io scheduler noop registered (default) ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 PPTP driver version 0.8.5 IMQ starting with 2 devices... IMQ driver loaded successfully. .Hooking IMQ after NAT on PREROUTING. .Hooking IMQ before NAT on POSTROUTING. tc3162: flash device 0x01000000 at 0x10000000 tc3162: Found SPIFLASH 16MiB MX25L12805D Creating 6 MTD partitions on "tc3162": 0x00000000-0x00010000 : "bootloader" 0x00010000-0x00020000 : "romfile" 0x00020000-0x0012e915 : "kernel" mtd: partition "kernel" doesn't end on an erase block -- force read-only 0x0012e915-0x00f52915 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x00020000-0x00fc0000 : "tclinux" 0x00fc0000-0x01000000 : "reservearea" RT3xxx EHCI/OHCI init. u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 GRE over IPv4 demultiplexor driver<6>GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Mac = 60:45:cb:8e:a:fc<6>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 160k freed busybox init and set aff init started: BusyBox v1.00 (2019.11.29-18:28+0000) multi-call binary. Sat Jan 1 00:00:00 UTC 2011 chmod: /userfs/profile.cfg: Read-only file system tcfullcone version: tcfullcone V1.1.0.0 (Feb 13 2012-20:16:35). module_sel: module license 'unspecified' taints kernel. tcportbind version: tcportbind V1.1.0.0 (Feb 13 2012-20:16:38). vlantag_drv_init TCSUPPORT_IPV6 TC3162 LED Manager 0.1 init tcledctrl version: tcledctrl V1.1.0.0 (Nov 30 2019-02:26:48). tccicmd V1.1.0.0 (Nov 30 2019-02:26:50) the number of cfg node is 81 register a node 0 register a node 1 register a node 2 register a node 3 register logAccess_init ter a node 5LanguageSwitch_init regivendorCfgFile_init ster a node 8 registarpstorm_init gisteThe number of cache node is 5 register a node 12 register a node 13 register a node 14 register a node 15 register a node 16 register a node 17 register a node 18 register a node 19 register a node 20 register a node 21 register a node 22 register a node 23 register a node 24 register a node 25 register a node 26 register a node 27 register a node 28 register a node 29 register a node 30 register a node 31 register a node 32 register a node 33 register a node 34 register a node 35 register a node 36 register a node 37 register a node 38 register a node 39 register a node 40 register a node 41 register a node 42 register a node 43 register a node 44 register a node 45 register a node 46 register a node 47 register a node 48 register a node 49 register a node 50 register a node 51 register a node 52 register a node 53 register a node 54 register a node 55 register a node 56 register a node 57 register a node 58 register a node 59 register a node 60 register a node 61 register a node 62 register a node 63 register a node 64 register a node 65 register a node 66 register a node 67 register a node 68 register a node 69 register a node 70 register a node 71 register a node 72 register a node 73 register a node 74 register a node 75 register a node 76 register a node 77 register a node 78 register a node 79 [do_parse_romfile, 27]Start [tc_parse_romfile, 245]Start [tc_parse_romfile, 257]opername(/dev/mtdblock1) [tc_parse_romfile, 260]check rom file(/dev/mtdblock1) [check_romfile, 108]pathname(/dev/mtdblock1) [check_romfile, 117]load XML file. mxml: Bad control character 0x1f not allowed by XML standard! [check_romfile, 174]2nd load XML file. [check_romfile, 204]verify rom file. [check_romfile, 217]return tree Check romfile pass![tc_parse_romfile, 382]rechecknum(0) [tc_parse_romfile, 389]laod backup romfile [loadRomfile, 77](1) [loadRomfile, 114]BK_ROMFILE_FLAG mtd[readflash]:device=reservearea tclen=65536 tcoffset=0 Unlocking reservearea ... Reading from reservearea to /tmp/tc_backupromfile ... [BK_ROMFILE_FLAG]/userfs/bin/mtd readflash /tmp/tc_backupromfile 65536 0 reservearea [tc_parse_romfile, 396]check backup romfile [check_romfile, 108]pathname(/tmp/tc_backupromfile) [check_romfile, 117]load XML file. mxml: Bad control character 0x1f not allowed by XML standard! [check_romfile, 174]2nd load XML file. [check_romfile, 204]verify rom file. [check_romfile, 217]return tree [tc_parse_romfile, 416]backup romfile is already exist. Dualwan set wan_primary=0 Dualwan set wan_secondary=-1 killall: wpa_supplicant: no process killed goto wlan_write!!killall: wpa_supplicwlnoan_write---goto fopen!!WPSActiveStatus = NULL WPSOOBActive = NULL ReCounterActive = NULL WPSGenPinCode = NULL write_wlan_AutoChannelSkipList -(0x20) [route_setting]remove interface[0]=[ppp0] generate miniupnpd.conf _gen_upnp_conf ==>syslog_write error, get WriteFlashInterval value failed ==>syslog_write error, get UpdateInterval value failed ==>syslog_write error, get AllLogSave value failed insmod raeth driver femac.c:v1.00-NAPI 29.Mar.2011 eth0: FE MAC Ethernet address: 60:45:CB:8E:0A:FC hotplug net INTERFACE=eth0 ACTION=add TSARM: TC3162 ATM SAR driver 1.5 init tc3162sar V1.2.0.0 (Nov 30 2019-02:26:46) register autopvc cmd to sys TSARM: TC3162 ATM SAR driver 1.5 done ifconfig: ra0: error fetching interface information: Device not found ra0 no private ioctls. ra0 No such device [main, 767]Init for web interface cfg node lanHost_read: Create node LanHost ! ADSL DMT initialization starting Begin AdslTaskInit..... End AdslTaskInit Begin to request IRQ 20 DMT:Succeed to request IRQ 20 Initializing ADSL F/W 3.20.56.24 ...... Reset dmtCheck DMT version =b2 ........ Initializing ADSL F/W ........ done ADSL HW version: b2, HCLK 166Cannot find device "br0" killall: tcapi: no process killed cfg_manager start to init server socket killall: ntpclient: no process killed setup_receive:: bind... pool.ntp.org: Unknown host TCSUPPORT_WLAN TCSUPPORT_WLAN_RT5392 The remaining IMEM space cannot accommodate section .text.imem !!Remaining IMEM space: -2544 bytes.Section Size: 764 bytesPCI: Enabling device 0000:01:00.0 (0000 -> 0002) === pAd = c00f1000, size = 506720 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 Efuse Size=0x2d [2d0-2fc] hotplug net INTERFACE=ra0 ACTION=add Mirror/redirect action on insmod: cannot open module `/lib/modules/2.6.22.15/kernel/net/sched/cls_fw.ko': No such file or directory insmod: cannot open module `/lib/modules/2.6.22.15/kernel/net/sched/sch_htb.ko': No such file or directory insmod: cannot open module `/lib/modules/2.6.22.15/kernel/net/sched/sch_prio.ko': No such file or directory Ebtables v2.0 registered igmpsnoop V1.1.0.0 (Feb 13 2012-20:16:36) mldsnooping V1.1.0.0 (Feb 13 2012-20:16:36) eth0: starting interface. alloc_sram p=bc000800 free=7800 alloc_sram p=bc002800 free=5800 TC2105MJ, <6>Ralink HW NAT Module Enabled hotplug net INTERFACE=br0 ACTION=add device eth0 entered promiscuous mode hotplug net INTERFACE=br1 ACTION=add TCSUPPORT_WLAN: ifconfig TCSUPPORT_WLAN_PERSSID_SWITCH disabled! (2)Going to bring up WiFi interfaces!! TCSUPPORT_WLAN_WDS SSH TC3162 hardware watchdog initialized Ethernet Media-Type Support monitorcfgmgr Copyright (C) 2013 ASUS Corp. Renjie_Lee@asus.com Jan 1 00:00:12 monitorcfgmgr[558]: [start monitorcfgmgr] four ports SIOCGIFFLAGS: No such device interface elan.1 does not exist! ERROR: trying to remove VLAN -:elan.1:- error: Invalid argument SIOCGIFFLAGS: No such device interface elan.2 does not exist! ERROR: trying to remove VLAN -:elan.2:- error: Invalid argument SIOCGIFFLAGS: No such device interface elan.3 does not exist! ERROR: trying to remove VLAN -:elan.3:- error: Invalid argument SIOCGIFFLAGS: No such device interface elan.4 does not exist! ERROR: trying to remove VLAN -:elan.4:- error: Invalid argument SIOCGIFFLAGS: No such device interface elan.5 does not exist! ERROR: trying to remove VLAN -:elan.5:- error: Invalid argument SIOCGIFFLAGS: No such device interface elan.6 does not exist! ERROR: trying to remove VLAN -:elan.6:- error: Invalid argument device eth0 is already a member of a bridge; can't enslave it to bridge br0. Added VLAN with VID == 1 to IF -:eth0:- WARNING: VLAN 1 does not work with many switches, consider another number if you have problems. hotplug net INTERFACE=eth0.1 ACTION=add elan.1: add 33:33:00:00:00:01 mcast address to master interface elan.1: add 01:00:5e:00:0g0:01 mcast address to master interface Added VLAN with VID == 2 to IF -:eth0:- hotplug net INTERFACE=eth0.2 ACTION=add elan.2: add 33:33:00:00:00:01 mcast address to master interface elan.2: add 01:00:5e:00:00:01 mcastT address to masCter interface Added VLAN with VID == 3 to IF -:eth0:- hotplug net INTERFACE=eth0.3 ACTION=add elan.3: add 33:33:00:00:00:01 mcast address to master interface elan.3: add 01:h00:5pe:00:00:01 mcasCt address to ma=ster interface Added VLAN with VID == 4 to IF -:eth0:- hotplug net INTERFACE=eth0.4 ACTION=add elan.4: add 33:33:00:00:00:01 mcast address to master interface elan.4: add 01:00:5e:0o0:00:01 mcast aEddress to masteTr interface device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state * phyaddr=0 Reg=00 value=8000* phyaddr=1 Reg=00 value=8000* phyaddr=2 Reg=00 value=8000* phyaddr=3 Reg=00 value=8000block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTISRAONadd USBPORT=(null) HOST=(null) DEVICE=(null) US bitswap on,DS bitswap onblock hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug IOlrONF=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTISet SNRM OFFSET = 5.0 dbl) HOST=(null) DEVICE=(null) offset = -2560/512 / -2560/512 blSet Agc Vref1 = 352 ; Vref2 F= 352 ; Vref3 =n 352) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) AGCb Vrekf1 = 352 ; Vref2 = 352 ; Vref3 = 352 ; VreOf4 = 352OST=(null) DEVICE=(null) Please reset DSL to use default setting!!!block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) block hotplug INTERFACE=(null) ACTION=add USBPORT=(null) HOST=(null) DEVICE=(null) hotplug net INTERFACE=br0 ACTION=add hotplug net INTERFACE=br0 ACTION=add hotplug net INTERFACE=br1 ACTION=add hotplug net INTERFACE=br1 ACTION=add hotplug net INTERFACE=elan.1 ACTION=add hotplug net INTERFACE=elan.2 ACTION=add hotplug net INTERFACE=elan.3 ACTION=add hotplug net INTERFACE=eth0 ACTION=add hotplug net INTERFACE=gre0 ACTION=add hotplug net INTERFACE=elan.4 ACTION=add hotplug net INTERFACE=imq0 ACTION=add hotplug net INTERFACE=elan.1 ACTION=add hotplug net INTERFACE=imq1 ACTION=add hotplug net INTERFACE=ip6tnl0 ACTION=add hotplug net INTERFACE=elan.2 ACTION=add hotplug net INTERFACE=ra0 ACTION=add hotplug net INTERFACE=teql0 ACTION=add hotplug net INTERFACE=sit0 ACTION=add hotplug net INTERFACE=lo ACTION=add hotplug net INTERFACE=elan.3 ACTION=add hotplug net INTERFACE=elan.4 ACTION=add hotplug net INTERFACE=gre0 ACTION=add hotplug net INTERFACE=imq0 ACTION=add hotplug net INTERFACE=eth0 ACTION=add hotplug net INTERFACE=imq1 ACTION=add hotplug net INTERFACE=lo ACTION=add hotplug net INTERFACE=ra0 ACTION=add ANNEXAIJLMDLA: start hotplug net INTERFACE=ip6tnl0 ACTION=add hotplug net INTERFACE=sit0 ACTION=add br0: port 5(elan.4) entering learning state br0: port 4(elan.3) entering learning state br0: port 3(elan.2) entering learning state br0: port 2(elan.1) entering learning state br0: topology change detected, propagating br0: port 5(elan.4) entering forwarding state br0: topology change detected, propagating br0: port 4(elan.3) entering forwarding state br0: topology change detected, propagating br0: port 3(elan.2) entering forwarding state br0: topology change detected, propagating br0: port 2(elan.1) entering forwarding state hotplug net INTERFACE=teql0 ACTION=add [cfgmgr](SIGCHLD:P979).. [cfgmgr](SIGCHLD:P981).. [cfgmgr](SIGCHLD:P983).. [cfgmgr](SIGCHLD:P985).. device br1 already exists; can't create bridge with the same name hotplug net INTERFACE=br2 ACTION=add check_and_set_iptv_ifname: a9fe359c(169.254.53.156) _ifconfig: name=br2 flags=1043 IFUP addr=169.254.53.156 netmask=255.255.0.0 hotplug net INTERFACE=br3 ACTION=add check_and_set_iptv_ifname: a9fe8eae(169.254.142.174) _ifconfig: name=br3 flags=1043 IFUP addr=169.254.142.174 netmask=255.255.0.0 hotplug net INTERFACE=br4 ACTION=add check_and_set_iptv_ifname: a9fe37ea(169.254.55.234) _ifconfig: name=br4 flags=1043 IFUP addr=169.254.55.234 netmask=255.255.0.0 update_wan_state(wan0_, 0, 0) update_wan_state(wan1_, 5, 0) update_wan_state(wan2_,=====) ===================insmod iptable_filter======================= date_wan_state(wan5_, 5, 0) update_wan_state(wan6_, 5, 0) update_wan_state(wan7_, 5, 0) update_wan_state(wan8_, 5, 0) update_wan_state(wan9_, 5, 0) update_wan_state(wan10_, 5, 0) update_wan_state(wan11_, 5, 0) update_wan_state(wan12_, 5, 0) ========================insmod ipt_REJECT======================= /etc/isp0.conf SIOCGIFFLAGS: No such device RFC1483/2684 bridge: Interface "nas0" created sucessfully RFC1483/2684 bridge: Communicating over ATM 0.8.32, encapsulation: LLC qos.txtp.traffic_class = 1 hotplug net INTERFACE=nas0 ACTION=add RFC1483/2684 bridge: Interface configured RFC1483/2684 bridge: RFC 1483/2684 bridge daemon started /etc/isp1.conf Plugin libpppoe.so loaded. RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7 /etc/isp2.conf /etc/isp3.conf /etc/isp4.conf /etc/isp5.conf /etc/isp6.conf /etc/isp7.conf /etc/isp8.conf /etc/isp9.conf /etc/isp10.conf /etc/isp11.conf /etc/isp12.conf Radvd is disabled dhcp6s is disabled! info, udhcpd (v0.9.9-pre) started error, Unable to open /etc/udhcpd.leases for reading goto wlan_boot!!!Interface doesn't accept private ioctl... set (8BE2): Network is down goto write_wlan_first_profile()!!write_wlan_AutoChannelSkipList -(0x20) xyyou : in pcie init function,need not reset RX DESC a3385000 size = 2048 pAd->ed_chk = 2 RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 efuse_probe::bUseEfuse = 1 NVM is EFUSE mode 1. Phy Mode = 9 2. Phy Mode = 9 NVM is efuse and its size =2d[2d0-2fc] NVM is efuse and the information is too less to bring up the interface Load EEPROM buffer from BIN, and force to use BIN buffer mode RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5 NVM is BIN mode now bb MainSsid mac 60:45:cb:8e:0a:fc 3. Phy Mode = 9 test--AntCfgInit: primary/secondary ant 0/1 bAutoTxAgcG = 1 MCS Set = ff ff 00 00 01 @@@ GetEDCCASupport: CountReg=[DE], DfsType=0, edcca_on=1, ed_chk=2 @@@ GetEDCCASupport: return TRUE @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 60:45:cb:8e:0a:fc <==== rt28xx_init, Status=0 0x1300 = 00064380 jiffies=ffff9543, POLLING_MODE_DETECT_INTV=300hotplug net INTERFACE=wds0 ACTION=add device ra0 entered promiscuous mode br0: port 1(ra0) entering learning state br0: topology change detected, propagating br0: port 1(ra0) entering forwarding state hotplug net INTERFACE=ra1 ACTION=add hotplug net INTERFACE=ra2 ACTION=add hotplug net INTERFACE=wds1 ACTION=add hotplug net INTERFACE=wds2 ACTION=add hotplug net INTERFACE=ra3 ACTION=add hotplug net INTERFACE=wds3 ACTION=add rai0 no private ioctls. rai0 no private ioctls. rai0 no private ioctls. BusyBox v1.00 (2019.11.29-18Di8sable Virtual Slerver / Port Forwardinge function. elete}] [cfgmgr](SIGCHLD:P1493).. nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading generate miniupnpd.conf _gen_upnp_conf launch upnp start_miniupnpd. force(1) stop upnp first /userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf & Disable Virtual Server / Port Forwarding function. [cfgmgr](SIGCHLD:P1558).. generate miniupnpd.conf _gen_upnp_conf launch upnp start_miniupnpd. force(1) stop upnp first killall_tk: waiting name=miniupnpd n=9 killall_tk: waiting name=miniupnpd n=8 networkmap is gn. launch it. killall_tk: waiting name=miniupnpd n=7 killall_tk: waiting name=miniupnpd n=6 killall_tk: waiting name=miniupnpd n=5 killall_tk: waiting name=miniupnpd n=4 killall_tk: waiting name=miniupnpd n=3 killall_tk: waiting name=miniupnpd n=2 killall_tk: waiting name=miniupnpd n=1 killall_tk: waiting name=miniupnpd n=0 killall_tk: SIGKILL name=miniupnpd n=9 killall_tk: SIGKILL name=miniupnpd n=8 killall_tk: SIGKILL name=miniupnpd n=7 killall_tk: SIGKILL name=miniupnpd n=6 killall_tk: SIGKILL name=miniupnpd n=5 killall_tk: SIGKILL name=miniupnpd n=4 killall_tk: SIGKILL name=miniupnpd n=3 killall_tk: SIGKILL name=miniupnpd n=2 killall_tk: SIGKILL name=miniupnpd n=1 nas0: no IPv6 routers present killall_tk: SIGKILL name=miniupnpd n=0 route: SIOC[ADD|DEL]RT/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf & Disable Virtual Server / Port Forwarding function. [cfgmgr](SIGCHLD:P1625).. generate miniupnpd.conf _gen_upnp_conf launch upnp start_miniupnpd. force(1) stop upnp first killall_tk: waiting name=miniupnpd n=9 killall_tk: waiting name=miniupnpd n=8 killall_tk: waiting name=miniupnpd n=7 killall_tk: waiting name=miniupnpd n=6 killall_tk: waiting name=miniupnpd n=5 killall_tk: waiting name=miniupnpd n=4 killall_tk: waiting name=miniupnpd n=3 killall_tk: waiting name=miniupnpd n=2 killall_tk: waiting name=miniupnpd n=1 killall_tk: waiting name=miniupnpd n=0 killall_tk: SIGKILL name=miniupnpd n=9 killall_tk: SIGKILL name=miniupnpd n=8 killall_tk: SIGKILL name=miniupnpd n=7 killall_tk: SIGKILL name=miniupnpd n=6 killall_tk: SIGKILL name=miniupnpd n=5 killall_tk: SIGKILL name=miniupnpd n=4 killall_tk: SIGKILL name=miniupnpd n=3 killall_tk: SIGKILL name=miniupnpd n=2 killall_tk: SIGKILL name=miniupnpd n=1 killall_tk: SIGKILL name=miniupnpd n=0 route: SIOC[ADD|DEL]RT/userfs/bin/sminiupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf & upnpd_boot _gen_upnp_conf start_miniupnpd. force(1) stop upnp first killall_tk: waiting name=miniupnpd n=9 killall_tk: waiting name=miniupnpd n=8 killall_tk: waiting name=miniupnpd n=7 killall_tk: waiting name=miniupnpd n=6 killall_tk: waiting name=miniupnpd n=5 killall_tk: waiting name=miniupnpd n=4 killall_tk: waiting name=miniupnpd n=3 killall_tk: waiting name=miniupnpd n=2 killall_tk: waiting name=miniupnpd n=1 killall_tk: waiting name=miniupnpd n=0 killall_tk: SIGKILL name=miniupnpd n=9 killall_tk: SIGKILL name=miniupnpd n=8 killall_tk: SIGKILL name=miniupnpd n=7 killall_tk: SIGKILL name=miniupnpd n=6 killall_tk: SIGKILL name=miniupnpd n=5 killall_tk: SIGKILL name=miniupnpd n=4 killall_tk: SIGKILL name=miniupnpd n=3 killall_tk: SIGKILL name=miniupnpd n=2 killall_tk: SIGKILL name=miniupnpd n=1 killall_tk: SIGKILL name=miniupnpd n=0 route: SIOC[ADD|DEL]RT/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf & [write_cur_romfile_in_flash, 456]write running romfile. Unlocking romfile ... Writing from /tmp/var/romfile.cfg.gz to romfile ... [ ]...[e]...[w]...[w]...[w]...[w].... [write_cur_romfile_in_flash, 464]write backup romfile in flash. [write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 0 reservearea mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536 Unlocking reservearea ... Writing from /tmp/var/romfile.cfg.gz to reservearea ... enter real action -----tclen:0x10000,tcoffset:0x0 writeflash: write 0 'st sector,start from 0x0,0x10000 bytes ...[e]...[w]....writeflash: total write 0x10000 bytes TCAPI save ok.killall: klogd: no process killed ftp switch turn onsip switch turn onh323 switch turn onrtsp switch turn onl2tp switch turn onipsec switch turn oniptables: No chain/target/match by that name. ifconfig: ppp0: error fetching interface information: Device not found [cfgmg #### wan_p5rimary: [] Ralink HW NAT Module Disabled killall: utelnetd: no process killed rmmod: hw_nat: No such file or directory get_iptv_ifname: nas0 check_and_set_iptv_ifname: a9fed8bd(169.254.216.189) _ifconfig: name=nas0 flags=1043 IFUP addr=169.254.216.189 netmask=255.255.0.0 rmmod: hw_nat: No such wol_boot rectory client_list_boot. launch networkmap arpstorm_boot Arpstorm_Entry_runin=0 cmd[0]=restart_pppoe_relay cmd[1]=0 [1779 service:handle_notifications +41] running: 3 pppoe_relay largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)Can't find Node(Info_dot1q), create it. Done. Can't find Node(USB), create it. Can't find Node(USB_Entry), create it. [write_cur_romfile_in_flash, 456]write running romfile. Unlocking romfile ... Writing from /tmp/var/romfile.cfg.gz to romfile ... [ ]...[e]...[w]...[w]...[w]...[w].... [write_cur_romfile_in_flash, 464]write backup romfile in flash. [write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 0 reservearea mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536 Unlocking reservearea ... Writing from /tmp/var/romfile.cfg.gz to reservearea ... enter real action -----tclen:0x10000,tcoffset:0x0 writeflash: write 0 'st sector,start from 0x0,0x10000 bytes ...[e]...[w]....writeflash: total write 0x10000 bytes TCAPI save ok.mtd[readflash]:device=reservearea tclen=65536 tcoffset=131072 Unlocking reservearea ... Reading from reservearea to /var/log/tmp_file ... [route_setting]remove interface[0]=[ppp0] Can't find Node(GUITemp), create it. Can't find Node(GUITemp_Entry1), create it. # Enable direct rule stop_nat_rules: apply the redirect_rules! start_usb Firmware version=[1.1.2.3] Please press Enter to activate this console. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb SCSI subsystem initialized Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ufsd: driver (lke_8.9.0 lke_8.9.0_r217400_b3, LBD=ON, acl, ioctl, sd, wb) loaded at c03da000 NTFS support included Big endian platform optimized: speed Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217400_b3 rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x1fbb0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Can't find Node(Vram), create it. Can't find Node(Vram_Entry), create it. ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x1fba0000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [write_cur_romfile_in_flash, 456]write running romfile. usbcore: registered new interface driver asix [write_cur_romfile_in_flash, 464]write backup romfile in flash. TCAPI save ok.Can't find Node(LogAccess_ToFile), create it. usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver rndis_host cdc_ncm: 14-Mar-2012 usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver cdc_wdm cdc_mbim: loaded usbcore: registered new interface driver cdc_mbim load: current_uptime = 0m, save_utime = 60m decomp: fname=/var/tmp/rstats-speed.gz start_pptpd: getpid= 730 [start_diskmon, 2802] [start_diskmon, 2804] decomp: gzip -dc /var/tmp/rstats-speed.gz > /var/tmp/rstats-uncomp != 0 init_ramusage() msgget ok set_msqid=0 ret_val=0 load: speed_count = 0 load: read source= save_path= load_history: fname=/var/tmp/rstats-history.gz decomp: fname=/var/tmp/rstats-history.gz decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0 decomp: fname=/var/tmp/rstats-history.gz decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0 load_history: load failed [diskmon_main, 2828] disk_monitor: starting... disk_monitor: day=1, week=6, time=1:0. disk_monitor: decide if scan the target... disk_monitor: 0: wait_second=79200... disk_monitor: wait_second=79200... disk_monitor: Pause... http_update_allowed_client-restrict_client(0): (0)clients [boa_sslInit, 24]Generate new key. calc: add WIRED as #0 calc: sync WIRED calc: add WIRELESS0 as #1 calc: sync WIRELESS0 calc: add ATM as #2 calc: sync ATM calc: add PTM0 as #3 calc: sync PTM0 calc: add PTM1 as #4 calc: sync PTM1 calc: add ETHERNETWAN as #5 calc: sync ETHERNETWAN calc: add BRIDGE as #6 calc: sync BRIDGE [boa_sslInit, 35]Enabling SSL security system mssl_init() mssl_[nboa_sslInit, 84]SSL security system enabled DSL-N14U login:

• boot into bootloader • >>

RT63365 at Mon Feb 13 20:40:38 CST 2012 Memory size 64MB flash base: b0000000 Found SPI Flash 16MiB MX25L12805D at 0xb0000000Bootloader version: 3.1 Search PHY addr and found PHY addr=1 Press reset button to boot command mode. Press any key in 1 secs to enter boot command mode. bldr> help ? Print out help messages. help Print out help messages. go Booting the linux kernel. decomp Decompress kernel image to ram. memrl <addr> Read a word from addr. memwl <addr> <value> Write a word to addr. dump <addr> <len> Dump memory content. jump <addr> Jump to addr. flash <dst> <src> <len> Write to flash from src to dst. flashrd <addr> <len> Read flash from addr. xmdm <addr> <len> Xmodem receive to addr. miir <phyaddr> <reg> Read ethernet phy reg. miiw <phyaddr> <reg> <value> Write ethernet phy reg. gpioon <gpio> Trigger power, internet, adsl led on. gpiooff <gpio> Trigger power, internet, adsl led off. cpufreq <freq num> / <m> <n> Set CPU Freq <156~450>(freq has to be multiple of 6) ipaddr <ip addr> Change modem's IP. httpd Start Web Server ddrdrv <..> Change DDR driving length bldr>

• cpuinfo, mtd • >>

# cat /proc/cpuinfo system type..: Ralink RT63365 SOC processor..: 0 cpu model..: MIPS 34K V5.5 BogoMIPS..: 332.59 wait instruction.: yes microsecond timers.: yes tlb_entries..: 64 extra interrupt vector.: yes hardware watchpoint.: yes ASEs implemented.: mips16 dsp mt shadow register sets.: 1 VCED exceptions..: not available VCEI exceptions..: not available unaligned accesses.: 6837 processor..: 1 cpu model..: MIPS 34K V5.5 BogoMIPS..: 249.85 wait instruction.: yes microsecond timers.: yes tlb_entries..: 64 extra interrupt vector.: yes hardware watchpoint.: yes ASEs implemented.: mips16 dsp mt shadow register sets.: 1 VCED exceptions..: not available VCEI exceptions..: not available unaligned accesses.: 6837 processor..: 2 cpu model..: MIPS 34K V5.5 BogoMIPS..: 249.85 wait instruction.: yes microsecond timers.: yes tlb_entries..: 64 extra interrupt vector.: yes hardware watchpoint.: yes ASEs implemented.: mips16 dsp mt shadow register sets.: 1 VCED exceptions..: not available VCEI exceptions..: not available unaligned accesses.: 6837 processor..: 3 cpu model..: MIPS 34K V5.5 BogoMIPS..: 249.03 wait instruction.: yes microsecond timers.: yes tlb_entries..: 64 extra interrupt vector.: yes hardware watchpoint.: yes ASEs implemented.: mips16 dsp mt shadow register sets.: 1 VCED exceptions..: not available VCEI exceptions..: not available unaligned accesses.: 6837 # cat /proc/mtd dev: size erasesize name mtd0: 00010000 00010000 "bootloader" mtd1: 00010000 00010000 "romfile" mtd2: 0010e915 00010000 "kernel" mtd3: 00e24000 00010000 "rootfs" mtd4: 00fa0000 00010000 "tclinux" mtd5: 00040000 00010000 "reservearea"

Images

• Internals
• 

  main board