ASUS DSL-N16/Bootlog

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search
See also: ASUS DSL-N16
 • Boot log
DRAMC V2.2.0.2 (0)

MT751020 at Thu Mar 31 12:04:09 CST 2016 free bootbase
Memory size 64MB
flash base: bc000000
Found SPI Flash 16MiB GD25Q128 at 0xbc000000
Bootloader version: 3.1

Search PHY addr and found PHY addr=8
Not found TC Phy
Press reset button to boot command mode.                                        
Press any key in 3 secs to enter boot command mode.                             
................................... 

Decompress to 80002000 free_mem_ptr=80600000 free_mem_ptr_end=80780000
75xx: 0x0 
Uncompressing [LZMA] ...  done.
Linux version 2.6.36 (root@localhost) (gcc version 4.3.4 (GCC) ) #1 SMP Tue Nov8
ISPRAM0: PA=00310000,Size=00008000,enabled
DSPRAM0: PA=1dff8000,Size=00001000,enabled
flash_init: flash_base:bc000000
flash_init: flash_base:bc000000
memsize:64MB
Ralink MT751020 SOC prom init
bootconsole [early0] enabled
CPU revision is: 00019555 (MIPS 34Kc)
Determined physical RAM map:
 memory: 03fe0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Zone PFN ranges:
  Normal   0x00000020 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000020 -> 0x00004000
3 available secondary CPU TC(s)
PERCPU: Embedded 7 pages/cpu @81083000 s7264 r8192 d13216 u65536
pcpu-alloc: s7264 r8192 d13216 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16224
Kernel command line:  es=1
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=0006498c
Readback ErrCtl register=0006498c
nmi base is 810c4200
Memory: 60660k/65408k available (3160k kernel code, 4748k reserved, 645k data, )
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1          
Hierarchical RCU implementation.                                                
        RCU-based detection of stalled CPUs is disabled.                        
        Verbose stalled-CPUs detection is disabled.                             
NR_IRQS:64                                                                      
CPU frequency 648.00 MHz                                                        
 Using 266.667 MHz high precision timer.                                        
console [ttyS0] enabled, bootconsole disabled                                   
console [ttyS0] enabled, bootconsole disabled                                   
Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)                         
pid_max: default: 32768 minimum: 301                                            
Mount-cache hash table entries: 512                                             
34K sync es set to 1.                                                           
Config7: 0x80080500                                                             
Limit of 4 TCs set                                                              
TLB of 64 entry pairs shared by 2 VPEs                                          
VPE 0: TC 0 1 2, VPE 1: TC 3                                                    
IPI buffer pool of 16 buffers                                                   
CPU revision is: 00019555 ((null))                                              
TC 1 going on-line as CPU 1                                                     
CPU revision is: 00019555 ((null))                                              
TC 2 going on-line as CPU 2                                                     
CPU revision is: 00019555 ((null))                                              
TC 3 going on-line as CPU 3                                                     
Brought up 4 CPUs                                                               
NET: Registered protocol family 16                                              
MT7510_pcie_init                                                                
check pcie link up status:                                                      
isRC0_LINKUP=0                                                                  
isRC1_LINKUP=1                                                                  
registering PCI controller with io_map_base unset                               
bio: create slab <bio-0> at 0                                                   
pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]                   
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]                   
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x200]
pci 0000:00:01.0: PCI bridge to [bus 01-01]                                     
pci 0000:00:01.0:   bridge window [io  disabled]                                
pci 0000:00:01.0:   bridge window [mem 0x20000000-0x200fffff]                   
pci 0000:00:01.0:   bridge window [mem pref disabled]                           
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)                                
NET: Registered protocol family 8                                               
NET: Registered protocol family 20                                              
Switching to clocksource MIPS                                                   
NET: Registered protocol family 2                                               
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                  
TCP established hash table entries: 2048 (order: 2, 16384 bytes)                
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)                       
TCP: Hash tables configured (established 2048 bind 2048)                        
TCP reno registered                                                             
UDP hash table entries: 128 (order: 0, 4096 bytes)                              
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)                         
NET: Registered protocol family 1                                               
TC3162 hardware watchdog module loaded.                                         
squashfs: version 4.0 (2009/01/31) Phillip Lougher                              
JFFS2 version 2.2 (NAND) (ZLIB) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.    
msgmni has been set to 118                                                      
io scheduler noop registered (default)                                          
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162                                   
brd: module loaded                                                              
tc3162 mtd init: mt6573_nand_init enter                                         
MediaTek MT6573 Nand driver init, version v2.0                                  
tc3162: flash device 0x01000000 at 0x1c000000                                   
tc3162: Found SPIFLASH 16MiB GD25Q128                                           
Creating 7 MTD partitions on "tc3162":                                          
0x000000000000-0x000000010000 : "bootloader"                                    
0x000000010000-0x000000020000 : "romfile"                                       
0x000000020000-0x00000016de44 : "kernel"                                        
mtd: partition "kernel" doesn't end on an erase block -- force read-only        
0x00000016de44-0x0000008ede44 : "rootfs"                                        
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-y
0x000000020000-0x000000ec0000 : "tclinux"                                       
0x000000ec0000-0x000000fc0000 : "jffs2"                                         
0x000000fc0000-0x000001000000 : "reservearea"                                   
PPP generic driver version 2.4.2                                                
PPP Deflate Compression module registered                                       
PPP BSD Compression module registered                                           
PPP MPPE Compression module registered                                          
NET: Registered protocol family 24                                              
PPTP driver version 0.8.5                                                       
RT3xxx EHCI/OHCI init.                                                          
u32 classifier                                                                  
    Actions configured                                                          
Netfilter messages via NETLINK v0.30.                                           
nf_conntrack version 0.5.0 (947 buckets, 3788 max)                              
ctnetlink v0.93: registering with nfnetlink.                                    
xt_time: kernel timezone is -0000                                               
GRE over IPv4 demultiplexor driver                                              
GRE over IPv4 tunneling driver                                                  
ip_tables: (C) 2000-2006 Netfilter Core Team                                    
TCP cubic registered                                                            
Initializing XFRM netlink socket                                                
NET: Registered protocol family 10                                              
IPv6 over IPv4 tunneling driver                                                 
NET: Registered protocol family 17                                              
NET: Registered protocol family 15                                              
L2TP core driver, V2.0                                                          
PPPoL2TP kernel driver, V2.0                                                    
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                   
All bugs added by David S. Miller <davem@redhat.com>                            
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.                
Freeing unused kernel memory: 212k freed                                        
busybox init and set aff                                                        
init started:  BusyBox v1.00 (2018.11.12-18:24+0000) multi-call binary          
Sat Jan  1 00:00:00 UTC 2011                                                    
chmod: /userfs/profile.cfg: Read-only file system                               
module_sel: module license 'unspecified' taints kernel.                         
Disabling lock debugging due to kernel taint                                    
                                                                                
tcsmux version: tcsmux V1.1.0.0 (Nov 13 2018-02:22:21).                         
                                                                                
tcportbind version: tcportbind V1.1.0.0 (Feb  5 2014-17:25:04).                 
vlantag_drv_init                                                                
TCSUPPORT_IPV6                                                                  
TC3162 LED Manager 0.1 init                                                     
                                                                                
tcledctrl version: tcledctrl V1.1.0.0 (Nov 13 2018-02:22:13).                   
tccicmd V1.1.0.0 (Nov 13 2018-02:22:18)                                         
the number of cfg node is 76                                                    
register a node 0                                                               
register a node 1                                                               
regislogAccess_init ter a nodeLanguageSwitch_init  2                            
rvendorCfgFile_init egister a node 3rpstorm_init                                
                                                                                
reThe number of cache node is 5                                                              
[do_parse_romfile, 27]Start                                                     
[tc_parse_romfile, 245]Start                                                    
[tc_parse_romfile, 257]opername(/dev/mtdblock1)                                 
[tc_parse_romfile, 260]check rom file(/dev/mtdblock1)                           
[check_romfile, 108]pathname(/dev/mtdblock1)                                    
[check_romfile, 117]load XML file.                                              
mxml: Bad control character 0x1f not allowed by XML standard!                   
[check_romfile, 174]2nd load XML file.                                          
[check_romfile, 204]verify rom file.                                            
[check_romfile, 217]return tree                                                 
Check romfile pass!                                                             
[tc_parse_romfile, 382]rechecknum(0)                                            
[tc_parse_romfile, 389]laod backup romfile                                      
[loadRomfile, 77](1)                                                            
[loadRomfile, 114]BK_ROMFILE_FLAG                                               
mtd[readflash]:device=reservearea tclen=65536 tcoffset=0                        
Unlocking reservearea ...                                                       
Reading from reservearea to /tmp/tc_backupromfile ...                           
[BK_ROMFILE_FLAG]/userfs/bin/mtd readflash /tmp/tc_backupromfile 65536 0 reserva
[tc_parse_romfile, 396]check backup romfile                                     
[check_romfile, 108]pathname(/tmp/tc_backupromfile)                             
[check_romfile, 117]load XML file.                                              
mxml: Bad control character 0x1f not allowed by XML standard!                   
[check_romfile, 174]2nd load XML file.                                          
[check_romfile, 204]verify rom file.                                            
[check_romfile, 217]return tree                                                 
[tc_parse_romfile, 416]backup romfile is already exist.                         
Dualwan set wan_primary=8                                                       
Dualwan set wan_secondary=-1                                                    
killall: wpa_supplicant: no process killed                                      
                                                                                
 goto wlan_write!!killall: wpa_supplic                                          
wlan_write---goto fopen!!ant: nWPSActiveStatus = NULL                           
o WPSOOBActive = NULL                                                           
prReCounterActive = NULL                                                        
ocWPSGenPinCode = NULL                                                          
ess killed                                                                      
write_wlan_AutoChannelSkipList -(0x20)                                          
write_wlan_profile() freq=0: Can not get the attribute wl0_HT_BADecline correct.
write_wlan_profile() freq=0: Can not get the attribugenerate miniupnpd.conf     
te wl0_HT_STBC correctly so use the default value 1.                            
write_wlan_profile() freq=0: Can not get the attribute wl0_location_code correc.
_gen_upnp_conf                                                                  
                                                                                
==>syslog_write error, get WriteFlashInterval value failed                      
                                                                                
==>syslog_write error, get UpdateInterval value failed                          
                                                                                
==>syslog_write error, get AllLogSave value failed                              
[cfgmgr](SIGCHLD:P207)..                                                        
insmod raeth driver                                                             
femac.c:v1.00-NAPI 29.Mar.2011                                                  
eth0: FE MAC Ethernet address: 60:xx:xx:xx:xx:xx                                
ifconfig: ra0: error fetching interface information: Device not found           
                                                                                
7510_debug: dmt_base_addr : bf900000                                            
ADSL DMT initialization starting                                                
Begin AdslTaskInit.....                                                         
End AdslTaskInit                                                                
Begin to  request IRQ 20                                                        
DMT:Succeed to request IRQ 20                                                   
Initializing ADSL F/W 5.5.2.10 ......                                           
Initializing ADSL F/W ........ done                                             
ra0       no private ioctls.                                                    
                                                                                
TCSUPPORT_WLAN                                                                  
ra0       No such device                                                        
                                                                                
[main, 767]Init for web interface cfg node                                      
                                                                                
lanHost_read: Create node LanHost !                                             
TCSUPPORT_WLAN_MT7592                                                           
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)                                
                                                                                
                                                                                
=== pAd = c1082000, size = 746648 ===                                           
                                                                                
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x                            
<-- RTMPAllocAdapterBlock, Status=0                                             
device_id =0x7603                                                               
RtmpChipOpsHook(507): Not support for HIF_MT yet!                               
mt7603_init()-->                                                                
mt_bcn_buf_init(224): Not support for HIF_MT yet!                               
<--mt7603_init()                                                                
Cannot find device "br0"                                                        
Mirror/redirect action on                                                       
killall: tcapi: no process killed                                               
cfg_manager start to init server socket                                         
SIOCGIFFLAGS: No such device                                                    
Ebtables v2.0 registered                                                        
killall: ntpclient: no process killed                                           
setup_receive:: bind...                                                         
pool.ntp.org: Unknown host                                                      
eth0: starting interface.                                                       
EPhy debug(8): tcPhyVerLookUp() in                                              
MT7510FE, EPhy debug(8)(15): tcPhyVerLookUp() out                               
PhyPart debug: tcPhyInit() in , tcphyver=15, phyaddr=8, eco=0x0                 
phyaddr = 8                                                                     
PhyPart debug: tcPhyInit() out , r31=0xb000                                     
EPhy debug(12): tcPhyVerLookUp() in                                             
MT7510Ge,Internal check flag: fgMT7510Ge_INT=0x0, eco=0x50003                   
EPhy debug(12)(16): tcPhyVerLookUp() out                                        
PhyPart debug: tcPhyInit() in , tcphyver=16, phyaddr=12, eco=0x0                
                                                                                
 7510Ge, phyaddr= (12,12)                                                       
debug... ,phyaddr=12 ,eco=0x50003                                               
PhyPart debug: tcPhyInit() out , r31=0xb000                                     
Ralink HW NAT Module Enabled                                                    
IP check use Black List                                                         
device eth0 entered promiscuous mode                                            
TCSUPPORT_WLAN: ifconfig                                                        
TCSUPPORT_WLAN_PERSSID_SWITCH disabled!                                         
(2)Going to bring up WiFi interfaces!!                                          
TCSUPPORT_WLAN_WDS                                                              
SSH                                                                             
TC3162 hardware watchdog initialized                                            
Ethernet Media-Type Support                                                     
monitorcfgmgr                                                                   
Copyright (C) 2013 ASUS Corp. Renjie_Lee@asus.com                               
                                                                                
Jan  1 00:00:13 monitorcfgmgr[377]: [start monitorcfgmgr]                       
                                                                                
four ports                                                                      
SIOCGIFFLAGS: No such device                                                    
interface elan.1 does not exist!                                                
ERROR: trying to remove VLAN -:elan.1:- error: No such device                   
SIOCGIFFLAGS: No such device                                                    
interface elan.2 does not exist!                                                
ERROR: trying to remove VLAN -:elan.2:- error: No such device                   
SIOCGIFFLAGS: No such device                                                    
interface elan.3 does not exist!                                                
ERROR: trying to remove VLAN -:elan.3:- error: No such device                   
SIOCGIFFLAGS: No such device                                                    
interface elan.4 does not exist!                                                
ERROR: trying to remove VLAN -:elan.4:- error: No such device                   
SIOCGIFFLAGS: No such device                                                    
interface elan.5 does not exist!                                                
ERROR: trying to remove VLAN -:elan.5:- error: No such device                   
SIOCGIFFLAGS: No such device                                                    
interface elan.6 does not exist!                                                
ERROR: trying to remove VLAN -:elan.6:- error: No such device                   
device eth0 is already a member of a bridge; can't enslave it to bridge br0.    
ethphxcmd used greatest stack depth: 13688 bytes left                           
Added VLAN with VID == 1 to IF -:eth0:-                                         
WARNING:  VLAN 1 does not work with many switches,                              
consider another number if you have problems.                                   
device elan.1 entered promiscuous mode                                          
Added VLAN with VID == 2 to IF -:eth0:-                                         
device elan.2 entered promiscuous mode                                          
Added VLAN with VID == 3 to IF -:eth0:-                                         
ip used greatest stack depth: 13656 bytes left                                  
device elan.3 entered promiscuous mode                                          
Added VLAN with VID == 4 to IF -:eth0:-                                         
device elan.4 entered promiscuous mode                                          
br0: port 1(eth0) entering disabled state                                       
* Phyaddr=8 RegAddr=00 value=8000                                               
* Phyaddr=9 RegAddr=00 value=8000                                               
* Phyaddr=10 RegAddr=00 value=8000                                              
* Phyaddr=11 RegAddr=00 value=8000                                              
[ used greatest stack depth: 13632 bytes left                                   
TSARM: MT7510 ATM SAR driver 1.0 init                                           
atmInit                                                                         
ATM SAR Time Base: 7065                                                         
atmInit 1.1 Version                                                             
ATM SAR Reset                                                                   
==============================================                                  
atm_init_wrappter                                                               
atm_init_wrappter                                                               
br2684_init                                                                     
                                                                                
 Mac = 60:xx:xx:xx:xx:xxpppoatm_init                                            
==============================================                                  
ATM SAR RX NAPI Mode                                                            
 mt7510_netdev_start                                                            
atm_dev: MT7510 ATM Ethernet address: 60:45:CB:16:4D:D8                         
 mt7510_atm_init: register_netdev success                                       
mt7510_atm_init: open genenral device                                           
mt7510_netdev_open                                                              
atm_dev: starting interface.                                                    
general device status: 3                                                        
atm_msg_buffer_init                                                             
txMsgNum: 720                                                                   
rxMsgNum: 512                                                                   
register autopvc cmd to sys                                                     
Channel:0, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:1, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:2, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:3, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:4, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:5, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:6, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
Channel:7, Type:1, Q0:0, Q1:0, Q2:0, Q3:0, Q4:0, Q5:0, Q6:0, Q7:0               
gzip used greatest stack depth: 13528 bytes left                                
[write_cur_romfile_in_flash, 456]write running romfile.                         
Unlocking romfile ...                                                           
Writing from /tmp/var/romfile.cfg.gz to romfile ...                             
 [w]                                                                            
[write_cur_romfile_in_flash, 464]write backup romfile in flash.                 
[write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 a
mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536      
Unlocking reservearea ...                                                       
Writing from /tmp/var/romfile.cfg.gz to reservearea ...                         
enter real action -----tclen:0x10000,tcoffset:0x0                               
writeflash: write 0 'st sector,start from 0x0,0x10000 bytes                     
writeflash: total write 0x10000 bytes                                           
                                                                                
TCAPI save ok.                                                                  
Jan  1 00:00:18 crond[595]: crond 2.3.2 dillon, started, log level 8            
                                                                                
The test lab:255                                                                
log cicmd 0 (wan  vdsl2  set  sra  on  )                                        
 US bitswap on,DS bitswap on                                                    
log cicmd 1 (wan  vdsl2  set  bs_tx  on  )                                      
 log cicmd 2 (wan  vdsl2  set  bs  on  )                                        
 G.VECTOR on                                                                    
gvt_ns_flag off                                                                 
Set SNRM OFFSET = 5.0 db                                                        
Set Agc Vref1 = 65535 ; Vref2 = 65535 ; Vref3 = 65535                           
log cicmd 3 (wan  vdsl2  set  target_snrm  32767  )                             
 PROFILE17A_MULTI_MODE                                                          
log cicmd 4 (wan  vdsl  set  agc  65535  65535  65535  65535  )                 
 log cicmd 5 (wan  vdsl  set  upbo  255  )                                      
 log cicmd 6 (wan  vdsl  set  sync_sym  10  )                                   
 G.inp mode                                                                     
ANNEXA                                                                          
annex auto-switch flag = 0                                                      
DLA: start                                                                      
br0: port 5(elan.4) entering forwarding state                                   
br0: port 5(elan.4) entering forwarding state                                   
br0: port 4(elan.3) entering forwarding state                                   
br0: port 4(elan.3) entering forwarding state                                   
br0: port 3(elan.2) entering forwarding state                                   
br0: port 3(elan.2) entering forwarding state                                   
br0: port 2(elan.1) entering forwarding state                                   
br0: port 2(elan.1) entering forwarding state                                   
Ralink HW NAT Module Disabled                                                   
Ralink HW NAT Module Enabled                                                    
IP check use Black List                                                         
done                                                                            
device br1 already exists; can't create bridge with the same name               
check_and_set_iptv_ifname: a9fef1b1(169.254.241.177)                            
_ifconfig: name=br2 flags=1043 IFUP addr=169.254.241.177 netmask=255.255.0.0    
check_and_set_iptv_ifname: a9fe828b(169.254.130.139)                            
_ifconfig: name=br3 flags=1043 IFUP addr=169.254.130.139 netmask=255.255.0.0    
check_and_set_iptv_ifname: a9fe88eb(169.254.136.235)                            
_ifconfig: name=br4 flags=1043 IFUP addr=169.254.136.235 netmask=255.255.0.0    
upd========================insmod iptable_filter=======================         
ate_wan_state(wan0_, 5, 0)                                                      
update_wan_state(wan1_, 5, 0)                                                   
update_wan_state(wan2_, 5, 0)                                                   
update_wan_state(wan3_, 5, 0)                                                   
update_wan_state(wan4_, 5, 0)                                                   
update_wan_state(wan5_, 5, 0)                                                   
update_wan_state(wan6_, 5, 0)                                                   
update_wan_state(wan7_, 5, 0)                                                   
update_wan_state(wan8_, 0, 0)                                                   
update_wan_state(wan9_, 5, 0)                                                   
update_wan_state(wan10_, 5, 0)                                                  
update_wan_state(wan11_, 5, 0)                                                  
update_wan_state(wan12_, 5, 0)                                                  
========================insmod ipt_REJECT=======================                
/etc/isp0.conf                                                                  
/etc/isp1.conf                                                                  
/etc/isp2.conf                                                                  
/etc/isp3.conf                                                                  
/etc/isp4.conf                                                                  
/etc/isp5.conf                                                                  
/etc/isp6.conf                                                                  
/etc/isp7.conf                                                                  
SIOCGIFFLAGS: No such device                                                    
/etc/isp8_0.conf                                                                
                                                                                
==>Error, socket or ioctl error for mulifctl                                    
SIOCGIFFLAGS: No such device                                                    
SIOCSIFHWADDR: No such device                                                   
SIOCSIFADDR: No such device                                                     
Plugin libpppoe.so loaded.                                                      
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5                        
pppd: unrecognipppd used greatest stack depth: 13392 bytes left                 
zed option 'nas8_0'                                                             
pppd version 2.4.5                                                              
Usage: pppd [ options ], where options are:                                     
        <device>        Communicate over the named device                       
        <speed>         Set the baud rate to <speed>                            
        <loc>:<rem>     Set the local and/or remote interface IP                
                        addresses.  Either one may be omitted.                  
        asyncmap <n>    Set the desired async map to hex <n>                    
        auth            Require authentication from peer                        
        connect <p>     Invoke shell command <p> to set up the serial line      
        crtscts         Use hardware RTS/CTS flow control                       
        defaultroute    Add default route through interface                     
        file <f>        Take options from file <f>                              
        modem           Use modem control lines                                 
        mru <n>         Set MRU value to <n> for negotiation                    
See pppd(8) for more options.                                                   
                                                    
/etc/isp10_7.conf                                                               
/etc/isp11.conf                                                                 
/etc/isp12.conf                                                                 
sh: /userfs/bin/zebra: not found                                                
sh: /userfs/bin/ripd: not found                                                 
Radvd is disabled                                                               
dhcp6s is disabled!                                                             
info, udhcpd (v0.9.9-pre) started                                               
error, Unable to open /etc/udhcpd.leases for reading                            
                                                                                
 goto wlan_boot!!!Interface doesn't accept private ioctl...                     
set (8BE2): Network is down                                                     
                                                                                
 goto write_wlan_first_profile()!!write_wlan_AutoChannelSkipList -(0x20)        
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_HT_BADecline .
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_HT_STBC corre.
write_wlan_first_profile() freq=0 : Can not get the attribute wl0_location_code.
TX_BCN DESC a1fb8000 size = 320                                                 
RX[0] DESC a1fba000 size = 2048                                                 
RX[1] DESC a1fbb000 size = 2048                                                 
cfg_mode=9                                                                      
cfg_mode=9                                                                      
wmode_band_equal(): Band Equal!                                                 
FW Version:CL173766-A                                                           
FW Build Date:20170925114906                                                    
CmdAddressLenReq:(ret = 0)                                                      
CmdFwStartReq: override = 1, address = 1048576                                  
CmdStartDLRsp: WiFI FW Download Success                                         
AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)                              
efuse_probe: efuse = 10000002                                                   
RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5                                   
RtmpEepromGetDefault::e2p_dafault=1                                             
RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 4, E2P default = 1          
NVM is BIN mode                                                                 
1. Phy Mode = 14                                                                
Cal Free IC!!                                                                   
now bb MainSsid mac 60:xx:xx:xx:xx:xx                                           
Country Region from e2p = ffff                                                  
tssi_1_target_pwr_g_band = 34                                                   
2. Phy Mode = 14                                                                
3. Phy Mode = 14                                                                
NICInitPwrPinCfg(14): Not support for HIF_MT yet!                               
NICInitializeAsic(585): Not support rtmp_mac_sys_reset () for HIF_MT yet!       
mt_mac_init()-->                                                                
mt7603_init_mac_cr()-->                                                         
AsicSetMacMaxLen(1829): Set the Max RxPktLen=1024!                              
<--mt_mac_init()                                                                
        WTBL Segment 1 info:                                                    
                MemBaseAddr/FID:0x28000/0                                       
                EntrySize/Cnt:32/128                                            
        WTBL Segment 2 info:                                                    
                MemBaseAddr/FID:0x40000/0                                       
                EntrySize/Cnt:64/128                                            
        WTBL Segment 3 info:                                                    
                MemBaseAddr/FID:0x42000/64                                      
                EntrySize/Cnt:64/128                                            
        WTBL Segment 4 info:                                                    
                MemBaseAddr/FID:0x44000/128                                     
                EntrySize/Cnt:32/128                                            
AntCfgInit(2570): Not support for HIF_MT yet!                                   
MCS Set = ff ff 00 00 01                                                        
networkmap is gn. launch it.                                                    
AsicSetRalinkBurstMode(4233): Not support for HIF_MT yet!                       
RTMPSetPiggyBack(879): Not support for HIF_MT yet!                              
AsicSetTxPreamble(4220): Not support for HIF_MT yet!                            
AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0                             
Main bssid = 60:45:cb:16:4d:d8                                                  
<==== rt28xx_init, Status=0                                                     
@@@ ed_monitor_init : ===>                                                      
@@@ ed_monitor_init : <===                                                      
jiffies=ffff9928, POLLING_MODE_DETECT_INTV=300                                  
ifconfig used greatest stack depth: 13200 bytes left                            
device ra0 entered promiscuous mode                                             
br0: port 1(ra0) entering forwarding state                                      
br0: port 1(ra0) entering forwarding state                                      
RTMPIoctlMAC():wrq->u.data.length=18, pointer(7fe51240)=60150004=0003001c!      
RTMPIoctlMAC():after trim space, ptr len=17, pointer(822d5000)=60150004=0003001!
ra0       mac:[0x21a04]:0003001c                                                
RTMPIoctlMAC():wrq->u.data.length=18, pointer(7faf7be0)=60200618=D7E87D10!      
RTMPIoctlMAC():after trim space, ptr len=17, pointer(822d5000)=60200618=D7E87D1!
ra0       mac:[0x10618]:d7e87d10                                                
rai0      no private ioctls.                                                    
                                                                                
rai0      no private ioctls.                                                    
                                                                                
rai0      no private ioctls.                                                    
                                                                                
==>Set_Debug_Proc()                                                             
<==Set_Debug_Proc(RTDebugLevel = 0)                                             
BusyBox v1.00 (2018.11.12-18:24+0000) multi-call Disable Virtual Server / Port .
binary                                                                          
                                                                                
Usage: route [{add|del|delete}]                                                 
                                                                                
nf_conntrack_rtsp v0.6.21 loading                                               
port #0: 554                                                                    
nf_nat_rtsp v0.6.21 loading                                                     
insmod used greatest stack depth: 12992 bytes left                              
generate miniupnpd.conf                                                         
_gen_upnp_conf                                                                  
launch upnp                                                                     
start_miniupnpd. force(1)                                                       
stop upnp first                                                                 
Unknown applet: add_ovpn_fw_rules                                               
/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/miniupnpd.conf &        
upnpd_boot                                                                      
_gen_upnp_conf                                                                  
start_miniupnpd. force(1)                                                       
stop upnp first                                                                 
route: SIOC[ADD|DEL]/userfs/bin/miniupnpd -P /var/log/upnpd.pid -f /var/tmp/min&
RT: File exists                                                                 
[write_cur_romfile_in_flash, 456]write running romfile.                         
Unlocking romfile ...                                                           
Writing from /tmp/var/romfile.cfg.gz to romfile ...                             
 [w]                                                                            
[write_cur_romfile_in_flash, 464]write backup romfile in flash.                 
[write_backup_romfile]/userfs/bin/mtd writeflash /tmp/var/romfile.cfg.gz 65536 a
mtd[writeflash]:device=reservearea tclen=65536 tcoffset=0 tcfilelen =65536      
Unlocking reservearea ...                                                       
Writing from /tmp/var/romfile.cfg.gz to reservearea ...                         
enter real action -----tclen:0x10000,tcoffset:0x0                               
writeflash: write 0 'st sector,start from 0x0,0x10000 bytes                     
writeflash: total write 0x10000 bytes                                           
                                                                                
TCAPI save ok.                                                                  
killall: klogd: no process killed                                               
ftp switch turn on                                                              
sip switch turn on                                                              
h323 switch turn on                                                             
rtsp switch turn on                                                             
l2tp switch turn on,sw_state=                                                   
iptables: Bad rule (does a matching rule exist in that chain?).                 
ipsec switch turn on,sw_state=                                                  
iptables: Bad rule (does a matching rule exist in that chain?).                 
iptables: No chain/target/match by that name.                                   
ifconfig: ppp80: error fetching interfa                                         
 #### wan_primary: []                                                           
ce information: Device not found                                                
                                                                                
killall: utelnetd: no process killed                                            
get_iptv_ifname: nas8_0                                                         
check_and_set_iptv_ifname: a9fe94c4(169.254.148.196)                            
_ifconfig: name=nas8_0 flags=1043 IFUP addr=169.254.148.196 netmask=255.255.0.0 
nas8_0: No such device                                                          
wol_boot                                                                        
client_list_boot. launch networkmap                                             
arpstorm_boot                                                                   
Arpstorm_Entry_runin=0                                                          
RTS debug message OFF!                                                          
cmd[0]=restart_pppoe_relay                                                      
cmd[1]=8                                                                        
[1880 service:handle_notifications +41] running: 3 pppoe_relay                  
http_update_allowed_client-restrict_client(0): (0)clients                       
log cicmd 0 (wan  dmt2  set  largeD  2  )                                       
 start_pptpd: getpid= 569                                                       
init_ramusage()                                                                 
msgget ok                                                                       
set_msqid=0                                                                     
ret_val=0                                                                       
mtd[readflash]:device=reservearea tclen=65536 tcoffset=131072                   
Unlocking reservearea ...                                                       
Reading from reservearea to /var/log/tmp_file ...                               
Can't find Node(Info_dot1q), create it.                                         
load: current_uptime = 0m, save_utime = 60m                                     
decomp: fname=/var/tmp/rstats-speed.gz                                          
decomp: gzip -dc /var/tmp/rstats-speed.gz > /var/tmp/rstats-uncomp != 0         
load: speed_count = 0                                                           
load: read source= save_path=                                                   
load_history: fname=/var/tmp/rstats-history.gz                                  
decomp: fname=/var/tmp/rstats-history.gz                                        
                                                                                
Done.                                                                           
decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0       
decomp: fname=/var/tmp/rstats-history.gz                                        
decomp: gzip -dc /var/tmp/rstats-history.gz > /var/tmp/rstats-uncomp != 0       
load_history: load failed                                                       
                                                                                
# Enable direct rule                                                            
stop_nat_rules: apply the redirect_rules!                                       
                                                                                
iwpriv used greatest stack depth: 12596 bytes left                              
iptables-restor used greatest stack depth: 12332 bytes left                     
calc: add WIRED as #0                                                           
calc: sync WIRED                                                                
calc: add WIRELESS0 as #1                                                       
calc: sync WIRELESS0                                                            
calc: add ATM as #2                                                             
calc: sync ATM                                                                  
grep used greatest stack depth: 12292 bytes left                                
Unknown applet: add_ovpn_fw_rules                                               
Warning: Driver for device ra0 has been compiled with version 22                
of Wireless Extension, while this program supports up to version 20.            
Some things may be broken...                                                    
                                                                                
calc: add PTM0 as #3                                                            
calc: sync PTM0                                                                 
calc: add PTM1 as #4                                                            
calc: sync PTM1                                                                 
calc: add ETHERNETWAN as #5                                                     
calc: sync ETHERNETWAN                                                          
calc: add BRIDGE as #6                                                          
calc: sync BRIDGE                                                               
*reg=00001fe0 value:200d4008 (ext_switch:0)                                     
Firmware version=[1.1.2.3]                                                      
                                                                                
Please press Enter to activate this console. Can't find Node(Vram), create it.  
Can't find Node(Vram_Entry), create it.                                         
Can't find Node(LogAccess_ToFile), create it.                                   

 • Available boot loader commands


?                                   Print out help messages.                    
help.                               Print out help messages.                    
go                                  Booting the linux kernel.                   
decomp                              Decompress kernel image to ram.             
memrl <addr>                        Read a word from addr.                      
memwl <addr> <value>                Write a word to addr.                       
dump <addr> <len>                   Dump memory content.                        
jump <addr>                         Jump to addr.                               
flash <dst> <src> <len>             Write to flash from src to dst.             
flashrd <addr> <len>                Read <len> data from flash <addr>.          
gpioon <gpio>                       Trigger power, internet, adsl led on.       
gpiooff <gpio>                      Trigger power, internet, adsl led off.      
xmdm <addr> <len>                   Xmodem receive to addr.                     
miir <phyaddr> <reg>                Read ethernet phy reg.                      
miiw <phyaddr> <reg> <value>        Write ethernet phy reg.                     
cpufreq <freq num> / <m> <n>        Set CPU Freq <156~450>(freq has to be multi)
ipaddr <ip addr>                    Change modem's IP.                          
httpd                               Start Web Server                            
ddrdrv <..>                         Change DDR driving length