(Est.) release date: March 2005
Country of manuf.: China
Power: 12 VDC, 0.5 A
Connector type: barrel
Conn. measurements: 5 mm (OD), 2.5 mm (ID), 10 mm (LEN)
CPU1: Infineon ADM5120P
FLA1: 1 MiB 1,048,576 B <br />8,192 Kib <br />1,024 KiB <br />8 Mib <br />9.765625e-4 GiB <br /> (Macronix MX29LV800BTC-70)
RAM1: 4 MiB 4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Winbond W981616CH-6 × 2)
Expansion IFs: none specified
Serial: yes, 4-pin header, populated, 3.3V TTL, (115200 8N1)
ETH chip1: Infineon ADM5120P
Switch: Infineon ADM5120P
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1
Stock FW OS: Nucleus RTOS
For a list of all currently documented Infineon (Lantiq) chipsets with specifications, see Infineon.
4-Port Router
- • Support page
"1244-00000382-010" and "Rev.A" is silkscreened on the board of the unit shown below.
- A date code of 0512 (March 2005) is etched onto the bottom of the board
- .. and is the basis for the release estimate in this entry.
- Caps on this board are S.Y. branded.
Info derived from the serial dumps below would seem to indicate
- the stock firmware is using the Nucleus RTOS.
Included PSU(s)
The power adapter included with the device is a DVE DVR-1250-B11.
- ID/OD/Len measurements used in the main infobox are approximate.
| DVE DVR-1250-B11 (more)
|
| Input: 120 VAC ~ 60 Hz, ? A
|
Input connector: NEMA 1-15P
Style: large, vertical Manuf. in: China Eff. level: 3
|
| Output: 12 VDC, 0.5 A
|
Output connector: barrel (center +)
OD: ?? ID: ?? LEN: ??
|
Serial
Pinout
JP1 [3.3v] [RxD] [GND] [TxD]
Info derived from
| Expand • boot log
|
ADM5120 Boot:+P
NetMall System Boot
Copyright 2002-2003 ADMtek, Inc.
CPU: ADM5120 Home Gateway Processor
POST Version: 2.02.0154
Creation Date: 2005.01.31
Press <space> key three times to stop autoboot...
0
Verifying product code......PASS
Boot Product Code!!!
+P
DHCPC:DHCP Client Started.
Setting well_known IP
DHCPS:DHCP Server Started.
IpDefenseCfg_Config.status = 1
==========================================================================
Renaissance project:
Command Line Interface. v.3.01.03 2005.03.23
==========================================================================
cmd>
easyconf::start!
waiting for data on port TCP 10101
|
| Expand • cmd> help
|
cmd> help
Command Line Interface v0.01
======================================================
rmem : Read memory.
Usage : rmem <Address> [Num of Words]
wmem : Write memory.
Usage : wmem <Address> <Data0> [Data1] ... [Data7]
rmi : read mii phy register.
Usage : rmi <phy addr> <reg>
wmi : write mii phy register.
Usage : wmi <phy addr> <reg> <Data>
time : Get current system time.
Usage : time
settime : Set system time.
Usage : settime <hh:mm:ss> [yy/mm/dd] [TZ(GMT +/- hour)]
help : List all commands.
Usage : help
mkdir : Make directories.
Usage : mkdir <dir>
create : Create files.
Usage : create <file>
cat : Concatenate files.
Usage : cat <file>
Press [q] to quit, any other key to continue..
ls : List directory contents.
Usage : ls [dir]
rm : Remove files.
Usage : rm <file>
rmdir : Remove directories.
Usage : rmdir <DIRECTORY>
copy : Copy files.
Usage : copy <source> <destination>
nvclear : Clear all of the NVFS files.
Usage : nvclear
routeShow : Show Route.
Usage : routeShow
mbufShow : Show Mbuf statistics.
Usage : mbufShow
ifShow : Dispaly network interface.
Usage : ifShow <ifname>
ifAllShow : Dispaly all network interface.
Usage : ifAllShow
taskShow : Show Task informations.
Usage : taskShow
Press [q] to quit, any other key to continue..
semShow : Show Semaphore informations.
Usage : semShow
timerShow : Show Timer informations.
Usage : timerShow
memShow : Show memory pool informations.
Usage : memShow
msgqShow : Show message queue informations.
Usage : msgqShow
eventShow : Show event group informations.
Usage : eventShow
knlShow : Show kernel resource informations.
Usage : knlShow
ipConfig : Configure interface address and subnet mask.
Usage : ipConfig [ifname] [ip] [subnet mask]
ipStatus : Change IP status. 1 for Enabled, 2 for Disabled..
Usage : ipStatus [ifname] [status]
ipAdd : Add alias IP address..
Usage : ipAdd [ifname] [ip] [netmask]
ipDel : Delete alias IP address..
Usage : ipAdd [ifname] [ip] [netmask]
Press [q] to quit, any other key to continue..
arpAdd : Add an ARP entry to ARP table..
Usage : arpAdd [ip] <Ethernet Address>
arpDel : Delete an ARP entry..
Usage : arpDel [ip]
arpGet : Get the hardware address of a specify IP..
Usage : arpGet [ip]
arpFlush : Flush ARP table..
Usage : arpFlush [ifname]
ping : Ping a host..
Usage : ping [ip] [ms]
dhcpcRelease: Release the IP address for the specified interface..
Usage : dhcpcRelease [ifname]
dhcpcRenew: Renew the IP address for the specified interface..
Usage : dhcpcRenew [ifname]
dhcpcLog : Show dhcpclog..
Usage : dhcpcLog
dhcpcLogTest: Test dhcpclog..
Usage : dhcpcLogTest [line_num]
dhcpsStart: Start DHCP Server..
Usage : dhcpsStart
Press [q] to quit, any other key to continue..
dhcpsStop : Stop DHCP Server..
Usage : dhcpsStop
dhcpsAddIp: Add static IP to the DHCP server.
Usage : dhcpsAddIp [mac(00-00-00-00-00-00)] [ip(xxx.xxx.xxx.xxx)]
dhcpsDelIp: Delete static IP from the DHCP server.
Usage : dhcpsDelIp [ip(xxx.xxx.xxx.xxx)]
dhcpsBindingNum: Print binding number of the DHCP server.
Usage : dhcpsBindingNum
dhcpsShowStatic: Print static IP of the DHCP server.
Usage : dhcpsShowStatic
natShow : Show NAT link table information.
Usage : natShow
natStart : Enable NAT function.
Usage : natStart
natStop : Disabled NAT function.
Usage : natStop
bindShow : Show NAT bind table information.
Usage : bindShow
upnpPMShow: Show UPnP port mapping table information.
Usage : upnpPMShow
Press [q] to quit, any other key to continue..
triggerPort: Set trigger port, when public port num is 0 will delete this entry..
Usage : triggerPort [index] [port] <protocol> [public port num] [start] [end] [protocol]....
triggerShow: Show trigger port information.
Usage : triggerShow
icqShow : Show ICQ link information.
Usage : icqShow
mmsShow : Show MMS link information.
Usage : mmsShow
gethostbyname: gethostbyname.
Usage : gethostbyname
tftpc : TFTP client.
Usage : tftpc <GET|PUT> <host> <remotename> <localname>
tftps : Start TFTP server.
Usage : tftps [dir] [timeout]
update : Update runtime code (need to download image file "download" to /tmp).
Usage : update
setAccessHost: Add/delete access host.
Usage : setAccessHost [NET(xx.xx.xx.xx)] [MASK (xx.xx.xx.xx)] <index>
accessHostShow: Show access host information.
Usage : accessHostShow
Press [q] to quit, any other key to continue..
ripStart : Enable RIP .
Usage : ripStart <version>
ripStop : Disable RIP .
Usage : ripStop
ripShow : Show RIP table .
Usage : ripShow
connectTest: Test the Connecting mode. .
Usage : connectTest [testing number]
upnp : UPnP switch. .
Usage : upnp [on/off]
upnpTest : Test UPnP. .
Usage : upnpTest [times]
|
| Expand • cmd> ifShow
|
cmd> ifShow
lo (unit number 0):
Flags: (0x8069) UP LOOPBACK MULTICAST ARP RUNNING
Type: SOFTWARE_LOOPBACK
Internet address: 127.0.0.1
Netmask 0xff000000 Subnetmask 0xff000000
Metric is 0
Maximum Transfer Unit size is 1536
0 packets received; 0 packets sent
0 multicast packets received
0 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
adm (unit number 0):
Flags: (0x9863) UP BROADCAST MULTICAST ARP RUNNING
Type: ETHERNET_CSMACD
Internet address: 192.168.2.1
Broadcast address: 192.168.2.255
Netmask 0xffffff00 Subnetmask 0xffffff00
Ethernet address is 00:0e:2e:5d:8e:b7
Metric is 0
Maximum Transfer Unit size is 1500
0 packets received; 17 packets sent
0 multicast packets received
17 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
adm (unit number 1):
Flags: (0x8863) UP BROADCAST MULTICAST ARP RUNNING
Type: ETHERNET_CSMACD
Ethernet address is 00:0e:2e:5d:8e:b8
Metric is 0
Maximum Transfer Unit size is 1500
0 packets received; 9 packets sent
0 multicast packets received
0 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
|
| Expand • cmd> taskShow
|
cmd> taskShow
Task Table List
-------------------------------------------------
Name Priority Status
=================================================
0. KnlTask 0 QUEUE_SUSPEND
1. tNetTas 50 SEMAPHORE_SUSPEND
2. tNvTask 100 SLEEP_SUSPEND
3. tDhcpcT 100 QUEUE_SUSPEND
4. tDnsPro 100 SEMAPHORE_SUSPEND
5. tDhcpsT 100 QUEUE_SUSPEND
6. tSntpc 100 READY
7. tHttpD 100 SEMAPHORE_SUSPEND
8. tHtpTsk 100 QUEUE_SUSPEND
9. clitask 5 READY
10. tUpnpD 100 READY
11. tUpnpTs 100 QUEUE_SUSPEND
12. tEasyCo 100 SEMAPHORE_SUSPEND
13. tDhcpPi 100 SLEEP_SUSPEND
14. powerbu 100 SLEEP_SUSPEND
-------------------------------------------------
|
| Expand • cmd> memShow
|
cmd> memShow
Memory Pool List
--------------------------------------------------------------------------
Name StartAddr Size MinAlloc Available Type TasksWaiting
===========================================================================
0. ShaMem 0x803F0000 65536 48 30896 FIFO 0
1. KenMem 0x802EB800 1067008 48 334292 FIFO 0
2. DskMem 0x80235000 747520 48 388 FIFO 0
3. UsrMem 0x80190394 674924 48 419956 FIFO 0
---------------------------------------------------------------------------
|
| Expand • cmd> knlShow
|
cmd> knlShow
Task Table List
-------------------------------------------------
Name Priority Status
=================================================
0. KnlTask 0 QUEUE_SUSPEND
1. tNetTas 50 READY
2. tNvTask 100 READY
3. tDhcpcT 100 QUEUE_SUSPEND
4. tDnsPro 100 SEMAPHORE_SUSPEND
5. tDhcpsT 100 QUEUE_SUSPEND
6. tSntpc 100 READY
7. tHttpD 100 READY
8. tHtpTsk 100 QUEUE_SUSPEND
9. clitask 5 READY
10. tUpnpD 100 SEMAPHORE_SUSPEND
11. tUpnpTs 100 QUEUE_SUSPEND
12. tEasyCo 100 SEMAPHORE_SUSPEND
13. tDhcpPi 100 SLEEP_SUSPEND
14. powerbu 100 SLEEP_SUSPEND
-------------------------------------------------
Memory Pool List
--------------------------------------------------------------------------
Name StartAddr Size MinAlloc Available Type TasksWaiting
===========================================================================
0. ShaMem 0x803F0000 65536 48 30896 FIFO 0
1. KenMem 0x802EB800 1067008 48 333716 FIFO 0
2. DskMem 0x80235000 747520 48 388 FIFO 0
3. UsrMem 0x80190394 674924 48 420024 FIFO 0
---------------------------------------------------------------------------
Semaphore Table List
-------------------------------------------------------
Name Type Count TasksWaitting
=======================================================
0. MFS_SEM FIFO 1 0
1. netSem FIFO 0 1
2. splSem FIFO 1 0
3. hosttbl FIFO 1 0
4. mblksem PRIORITY 1 0
5. mclsem PRIORITY 1 0
6. FLSH FIFO 1 0
7. sio_Rx0 FIFO 0 0
8. sio_RT0 FIFO 0 0
9. NVRAM FIFO 1 0
10. downloa FIFO 1 0
11. user_cf FIFO 1 0
12. pppoe_c FIFO 1 0
13. pptp_cf FIFO 1 0
14. dhcpc_c FIFO 1 0
15. dhcpcLo FIFO 1 0
16. DhcpcSe FIFO 1 0
17. dhcpcMu FIFO 1 0
18. dhcpcEv FIFO 1 0
19. dhcp_ti FIFO 1 0
20. leaseSe FIFO 1 0
21. ip_cfg FIFO 1 0
22. nat_cfg FIFO 1 0
23. route_c FIFO 1 0
24. dns_rel FIFO 1 0
25. dhcps_c FIFO 1 0
26. time_zo FIFO 1 0
27. sntpc_c FIFO 1 0
28. sotSem FIFO 1 0
29. sorSem FIFO 1 0
30. sosSem FIFO 1 0
31. ip_fire FIFO 1 0
32. ip_defe FIFO 1 0
33. ip_filt FIFO 1 0
34. url_fil FIFO 1 0
35. http_cf FIFO 1 0
36. access_ FIFO 1 0
37. ethftr_ FIFO 1 0
38. upnp_cf FIFO 1 0
39. sotSem FIFO 1 0
40. sorSem FIFO 1 0
41. sosSem FIFO 1 0
42. sotSem FIFO 1 0
43. sorSem FIFO 1 0
44. sosSem FIFO 1 0
45. sotSem FIFO 1 0
46. sorSem FIFO 1 0
47. sosSem FIFO 1 0
48. sotSem FIFO 1 0
49. sorSem FIFO 1 0
-------------------------------------------------------
Timer Table List
-------------------------------------------------------
Name Status InitialTime Expirations
=======================================================
0. t0 Enable 100 0
<.. the system crashes at this point (or before)>
|
bootloader info
| Expand • text on autoboot abort
|
ADM5120 Boot:+P
NetMall System Boot
Copyright 2002-2003 ADMtek, Inc.
CPU: ADM5120 Home Gateway Processor
POST Version: 2.02.0154
Creation Date: 2005.01.31
Press <space> key three times to stop autoboot...
3
Net Routing Table:
Destination Gateway NetMask Flags Used Hops Interface
-------------------------------------------------------------------------------
POST Menu
=========================
[1] Xmodem Download
[2] TFTP Client Download
[3] TFTP Server Download
[4] Print Boot Params
[5] Set Boot Params
[6] Set Boot Mode
[7] Exit
Please enter your number:
|
| Expand • boot params
|
Please enter your number: 4
Print Boot Parameters.
==========================
Serial number: 506B3000725
Hardware version: F5D5231-4
Mac addres: 00-0e-2e-5d-8e-b7
Number of Mac address: 2
Number of configured interface: 0
|
Images
