Belkin F5D9231-4 v1

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Belkin F5D9231-4 v1

Manuf (OEM/ODM): Arcadyan WG7005D12 1-LF-AK

FCC approval date: 09 July 2008
Country of manuf.: China

Type: wireless router

FCC ID: K7SF5D9231A
IC ID: 3623A-F5D9231A
PCB ID: 141700520007J

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: Ralink RT2880 (266 MHz)
FLA1: 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Eon EN29LV160AB-70TCP)
RAM1: 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (ISSI IC42S16400F-7TL × 2)

Expansion IFs: none specified
Serial: yes, internal, 10-pin header, populated, 3.3V TTL, (115200,8,N,1), J2

WI1 chip1: Ralink RT2880
WI1 chip2: Ralink RT2820
WI1 802dot11 protocols: bg
WI1 MIMO config: 1x2:1
WI1 antenna connector: none

ETH chip1: Ralink RT2880
Switch: IC+ IP175C
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1

bg

Additional chips
2.4GHz Power Amplifier IC;Richwave;RTC6694;188, 6694, A828;2;SiGe;QFN24;

Stock FW OS: SuperTask!

Default SSID: Belkin_G+MIMO_Wireless_XXXXXX
Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 295 additional devices
of which 97 are Belkin devices

802dot11 OUI: 00:1C:DF (16 E, 33 W), 00:22:75 (13 E, 21 W)
Ethernet OUI: 00:1C:DF (16 E, 33 W), 00:22:75 (13 E, 21 W)

For a list of all currently documented Ralink chipsets with specifications, see Ralink.


Wireless G+ MIMO Router

 • Support page

"P/N: 141700520007J", "R01", and "RoHS" within a triangle

is silkscreened on one F5D9231 v1's board.

Labels affixed to the device indicate it has an internal

Arcadyan model of WG7005D12 1-LF-AK.

This would seem to be another Arcadyan device using

the SuperTask! RTOS.

The default SSID follows the pattern of Belkin_G+MIMO_Wireless_XXXXXX

where XXXXXX is the last three octets of the wireless interface MAC
w/ upper case letters. OUIs may include 00:22:75.

Serial

Pinout

(   ) (GND)    ----> to RT2880
(   ) (   )
(   ) (TxD)
(   ) (RxD)
(   ) [   ]
           J2

Info derived from

 • boot log • >>
 Ready Set Value = 0x0511FFA1

 Setup FLASH_CS1_CFG = 0511FFA1

Disable all eth ports!!

=======================================================================
Wireless Gateway WG7005D Loader V0.13 build Sep 17 2007 16:56:36
                    Arcadyan Technology Corporation
=======================================================================
EON EN29LV160AB bottom boot 16-bit mode found

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...
Flash Checking
 Passed.

Unzipping firmware at 0x88002000 ... [ZIP 3] [ZIP 1]  done
Enable all eth ports!!

In c_entry() function ...
CPU : RT2880  Chip V1.4, CPU Speed 266 MHz, Interrups Status 00000000
install_exception
Co config = 80240483
sys_irq_init ...
mips_int_connect : intnum 2 hdl 88008d28
IrqEnable : IRQ = 8
##### _ftext      = 0x88002000
##### _fdata      = 0x88392500
##### __bss_start = 0x884074FC
##### end         = 0x88DEC568
##### Backup Data from 0x88392500 to 0x88DF4568~0x88E69564 len 479228
##### Backup Data completed
##### Backup Data verified
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 266000000 Hz
mips_counter_frequency:133000000
r4k_offset: 0x00020788(133000)
init_US_counter : time1 = 208660 , time2 = 32208706, diff 32000046
US_counter = 59
 cnt1 32975574 cnt2 32976809, diff 1235
mips_int_enable: 7
mips_int_enable 1: s = 8401
mips_int_enable 2: s = 8401
mips_int_enable 3: s = 0
Runtime code version: 1.00.01
System startup...
[INIT] Memory COLOR 0, 800000 bytes ..
[INIT] Memory COLOR 1, 600000 bytes ..
[INIT] Memory COLOR 2, 607200 bytes ..
EON EN29LV160AB bottom boot 16-bit mode found
Set flash memory layout to BRN-BOOT
Boot Parameters found !!!
Bootcode version: V0.13
Serial number: 12834923110139
Hardware version: 01
EON EN29LV160AB bottom boot 16-bit mode found

sizeof(struct III_Config_t) is 88048, nLen:88048, Magic:0xffffffff
!![E-CFG-VER] Configuration data version mismatch!!
!![E-CFG-VER] Adapting factory defaults!!
!![E-CFG-VER] Reconfiguration required!!
!!No configuration file present!!
!!Cleanup configuration in flash memory!!
EON EN29LV160AB bottom boot 16-bit mode found
>>>>>No config, SKU=1
!!! Invalid wireless channel range 255 ~ 255
!!! Use default value 1 ~ 13
default route: 0.0.0.0
BufferInit:
BUF_HDR_SZ=160 BUF_ALIGN_SZ=28 BUFFER_OFFSET=384
BUF_BUFSZ0=544 BUF_BUFSZ1=4320
NUM_OF_B0=0 NUM_OF_B1=900
BUF_POOL0_SZ=0 BUF_POOL1_SZ=4032000
sizeof(BUFFER0)=704,sizeof(BUFFER1)=4480
*BUF0=0x88b5a12c *BUF1=0x88781b0c
Altgn *BUF0=0x88b5a140 *BUF1=0x88781b20
End at BUF0:0x88b5a140, BUF1:0x88b5a120

BUF0[0]=0x88b5a140 BUF1[0]=0x88781b20

buffer0 pointer init OK!
buffer1 pointer init OK!
ifno=  0, Link_Type= 4
time = 08/01/2003, 00:00:00
Interface 0 ip = 127.0.0.1

ifno=  1, Link_Type= 1
need to reset Ethernet switch????
MAC Address: 00:1c:df:e5:fa:25
debug: dev_raether irq is 3(eth2)
dev->priv 8860cbd0
  sb =  0 1C DF E5 FA 25
GDMA1_MAC_ADRH -- : 0x0000001c
GDMA1_MAC_ADRL -- : 0xdfe5fa25
RA2880 Ethernet Driver Initilization. v1.01  128 rx/tx descriptors allocated!
  sb =  0 1C DF E5 FA 25
GDMA1_MAC_ADRH -- : 0x0000001c
GDMA1_MAC_ADRL -- : 0xdfe5fa25
ra2880_setup_dev_fptableis called!
ICPLUS 175C config LAN_WAN finished (demo board)
IC-Plus PHY Init...ok
DSP_EN OFF version driver

phy_tx_ring = 0840a640, tx_ring = a840a640, size: 16 bytes

phy_rx_ring = 0840aa40, rx_ring = a840aa40, size: 16 bytes
should set VLAN ??????????????
@@@@@@@@@@@@@@@@@@ Set LAN and WAN VLAN....
mips_int_connect : intnum 5 hdl 88009974
mips_int_enable: 5
mips_int_enable 1: s = 8401
mips_int_enable 2: s = a401
mips_int_enable 3: s = 0
time = 08/01/2003, 00:00:00
Interface 1 ip = 192.168.2.1

ifno=  2, Link_Type= 1
hwlan_init(376): [HWLAN] ifno=2 irno=7 port=0x00000000
RT2860_init_module
2860 version : v1.6.0.0 (2007/10/12)
--> RTMPAllocAdapterBlock
RTMP_ADAPTER_mem : 884c6b84, sizeof(RTMP_ADAPTER) 465448

=== pAd = 884C6B84, size = 465448 ===

<-- RTMPAllocAdapterBlock, Status=0
ra0: at CSR addr 0xa0480000.
RUNTASK id=1 hwlan_light_isr...
time = 08/01/2003, 00:00:00
Interface 2 ip = 192.168.2.1

ifno=  3, Link_Type= 1
WAN MAC Address: 00:1c:df:e5:fa:26
MAC Address: 00:1c:df:e5:fa:26
should set VLAN ??????????????
time = 08/01/2003, 00:00:00
iput_IpLinkUp(ifno=3)> ifp->add_default_route:1
Re-Init NAT data structure
Init NAT data structure
Interface 3 ip = 0.0.0.0

ifno=  4, Link_Type= 0
ifno=  5, Link_Type= 0
ifno=  6, Link_Type= 0
ifno=  7, Link_Type= 0
ifno=  8, Link_Type= 0
ifno=  9, Link_Type= 0
ifno= 10, Link_Type= 0
ifno= 11, Link_Type= 0
ifno= 12, Link_Type= 0
ifno= 13, Link_Type= 0
ifno= 14, Link_Type= 0
ifno= 15, Link_Type= 0
ifno= 16, Link_Type= 0
ruleCheck()> Group: 0,  Error: Useless rule index will be truncated
ruleCheck()> Group: 1,  Error: Useless rule index will be truncated
ruleCheck()> Group: 2,  Error: Useless rule index will be truncated
ruleCheck()> Group: 3,  Error: Useless rule index will be truncated
ruleCheck()> Classify Rule: 1,  Error: Protocol Field
ruleCheck()> Classify Rule: 2,  Error: Protocol Field
ruleCheck()> Classify Rule: 3,  Error: Protocol Field
ruleCheck()> Classify Rule: 4,  Error: Protocol Field
ruleCheck()> Classify Rule: 5,  Error: Protocol Field
ruleCheck()> Classify Rule: 6,  Error: Protocol Field
ruleCheck()> Classify Rule: 7,  Error: Protocol Field
ruleCheck()> Classify Rule: 8,  Error: Protocol Field
ruleCheck()> Classify Rule: 9,  Error: Protocol Field
ruleCheck()> Classify Rule: 10,  Error: Protocol Field
ruleCheck()> Classify Rule: 11,  Error: Protocol Field
ruleCheck()> Classify Rule: 12,  Error: Protocol Field
ruleCheck()> Classify Rule: 13,  Error: Protocol Field
ruleCheck()> Classify Rule: 14,  Error: Protocol Field
ruleCheck()> Classify Rule: 15,  Error: Protocol Field
ruleCheck()> Classify Rule: 16,  Error: Protocol Field
ruleCheck()> Classify Rule: 17,  Error: Protocol Field
ruleCheck()> Classify Rule: 18,  Error: Protocol Field
ruleCheck()> Classify Rule: 19,  Error: Protocol Field
ruleCheck()> Classify Rule: 20,  Error: Protocol Field
ruleCheck()> Classify Rule: 21,  Error: Protocol Field
ruleCheck()> Classify Rule: 22,  Error: Protocol Field
ruleCheck()> Classify Rule: 23,  Error: Protocol Field
ruleCheck()> Classify Rule: 24,  Error: Protocol Field
ruleCheck()> Classify Rule: 25,  Error: Protocol Field
ruleCheck()> Classify Rule: 26,  Error: Protocol Field
ruleCheck()> Classify Rule: 27,  Error: Protocol Field
ruleCheck()> Classify Rule: 28,  Error: Protocol Field
ruleCheck()> Classify Rule: 29,  Error: Protocol Field
ruleCheck()> Classify Rule: 30,  Error: Protocol Field
ruleCheck()> Classify Rule: 31,  Error: Protocol Field
ruleCheck()> Classify Rule: 32,  Error: Protocol Field
reqCBACBuf()> init match pool, Have: 500
Memory Address: 0x88dc89b4 ~ 0x88dcc080
reqCBACBuf()> init timeGap pool, Have: 5000
Memory Address: 0x88dcc080 ~ 0x88de4734
reqCBACBuf()> init sameHost pool, Have: 1000
Memory Address: 0x88de4734 ~ 0x88dec454
[setClsfyEnable] clsfy_func=0
CBAC rule pool initialized !!
[init_if] local_if_mask=0x7
[init_if] local_wiredif_mask=0x2
[init_if] local_wirelessif_mask=0x4
[init_if] localorVPN_if_mask=0x1dc07
Init NAT data structure
No default route, no need to reinit the NAT data structure
RUNTASK id=2 if_task if0...
RUNTASK id=3 if_task if1...
RUNTASK id=4 if_task if2...
RUNTASK id=5 if_task if3...
RUNTASK id=6 timer_task...
RUNTASK id=7 conn_mgr...
RUNTASK id=8 main_8021x...
RUNTASK id=9 main_lltd...
RUNTASK id=10 period_task...
RUNTASK id=11 dhcp_daemon...
RUNTASK id=12 dhcp_clt...on interface 3
RUNTASK id=13 pptp_callmgr...
RUNTASK id=14 L2tpd...
found signature: 78h 56h 34h 12h
ulImgLens=997933, LENGTH[3]-12=1769460
length checking OK
[0] find End at 0xBC133800 len=997933
---[ LZMA head start in 0xBC133C00 ]---
found signature: 78h 56h 34h 12h
ulImgLens=112590, LENGTH[3]-12=1769460
length checking OK
[1] find End at 0xBC14F000 len=112590
Image[1] at 0xBC040000, len = 997933
Image[2] at 0xBC133C00, len = 112590
Unzipping from BC133C00 to 88EE2000 ... [ZIP 1] done
Uncompressed size = 1051075
drive start addr[0]=88ee2000, [1]=88fe29d0
[HTTPD] flash_init: failed!!
httpd: listen at 192.168.2.1:80
RUNTASK httpd...
RUNTASK id=17 dnsproxy...
RUNTASK id=18 rip...
RUNTASK id=19 ripout...
RUNTASK id=20 dhcpd_mgmt_task...
UPnP is enabled
UPNP Device initialize success! slot=21
gConfig.WSC_Mode:1
RUNTASK id=22 wscmain...
RUNTASK id=23 wsc_Send_eap_packet...
RUNTASK id=24 wsc_Send_UPNP_packet...
RUNTASK id=25 WSC_WaitUserAction_Task...
gConfig.WSC_Mode:1
RUNTASK id=26 led_task...

>>> belkin_wan_cfg task runs successfully, task_id = 27
UART RX Input
Starting Multitask...
run_project_task
RUNTASK id=28 apAppInit...
dot1x_build_if_mapping ifno2dot1x_if[2]=0
dot1x_build_if_mapping dot1x_wireless_if_mask=0x4
dot1x_build_if_mapping() completed.
init psock cnt=-805885241
mips_int_connect : intnum 6 hdl 880af3f0
mips_int_enable: 6
mips_int_enable 1: s = a400
mips_int_enable 2: s = e400
mips_int_enable 3: s = 0
rt2860_open : should call request_irq ????????????????????????
rt2860_open 1
rt2860_open 2
rt2860_init 1
rt2860_init 2
rt2860_init 3
rt2860_init 6
rt2860_init 8
RX DESC A8414640  size = 2048
<-- RTMPAllocDMAMemory, Status=0
rt2860_init 9
rt2860_init 10
sizeof(RT2860AP_DAT) : 1314
HT: Auto BA  = Enable
HT: MCS = AUTO
HT: STBC = 1
gSetting.GTxRateBitmap=0
gSetting.NTxRateMCS=33
gSetting.WirelessMode=0
1. Phy Mode = 9
2. Phy Mode = 9
sould check E2PROM MAC ?????????????????
EEPROM_NIC1 212
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
CarrierDetect.Enable=0
Main bssid = 00:1c:df:e5:fa:25
<==== RTMPInitialize, Status=0
rt2860_open 3
should Set up the Mac address ?????????
rt2860_open 4
rt2860_open 5
rt2860_open 6
0x1300 = 00064300
netif_carrier_on() called ???
[dhcp_clt] enable dhcp client in interface WAN[3]
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.02, Jul 17 2008 17:50:32
*********************************************
Initializing stack...
---------in wsc init----------
----------sizeof(uint32)=4
----------sizeof(uint-long)=4
----------sizeof(uint32)=2
@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@
wsc_Send_eap_packet:udpFdupnp_wcn:28;;udpFdupnp:2a
WSC_WaitUserAction:wait user action:0
[HWLAN] [30] rapi_tmr_task running
[22]pthread_cond_init: 0
[22]pthread_mutex_init: resource No. 34
[22]pthread_mutex_init: resource No. 35
[PORTABLITY]:WscCreateThread--------------------
 Entered udp_read
WscCmd:ActualCBThreadProc: Started
[htf_dbg]     - OnlineActiveWirless() 1608
[ipriv]:[ipriv]:[ipriv]:[ipriv]:CarrierDetect.Enable=0
[22]pthread_cond_init: 1
[22]pthread_mutex_init: resource No. 36
[22]pthread_mutex_init: resource No. 37
[PORTABLITY]:WscCreateThread--------------------
 WscCmd:ActualUIThreadProc: Started.
ActualUIThreadProc: wait q
MasterControl constructor
WscCmd::MC instantiated ok
[22]pthread_cond_init: 2
[22]pthread_mutex_init: resource No. 38
[22]pthread_mutex_init: resource No. 39
[PORTABLITY]:WscCreateThread--------------------
 [22]pthread_mutex_init: resource No. 40
[PORTABLITY]:pthread_mutex_init--------------------
 CTransport Construction
[22]pthread_cond_init: 3
[22]pthread_mutex_init: resource No. 41
[22]pthread_mutex_init: resource No. 42
[PORTABLITY]:WscCreateThread--------------------
 In CTransport::ActualCBThreadProc
ActualCBThreadProc: Calling Dequeue
MC::Init: Init complete ok
WscCmd::MC intialized ok
WscCmd::Init ok, starting stack...
Info::ReadConfigFile: Called
Info::ReadConfigFile:
Info::ReadConfigFile:File open ok
******************uuid_p:0x00000000000000011000001cdfe5fa25*****
mp_deviceInfo->uuid[i]:
0-0-0-0-0-0-0-1-10-0-0-1c-df-e5-fa-25-
mp_deviceInfo->macAddr:00:1C:DF:E5:FA:25
gSetting.dot1x.if_entry[0].enableWEP:0
temp_value=cff72ac7
authTypeFlags is 1 ,encrTypeFlags is 1 ,m_nwKey is , key len is 0
 ssid is Belkin_G+MIMO_Wireless_E5FA25
S, cb7
E, fd1
RegistrarSM constructor
[22]pthread_cond_init: 4
[22]pthread_mutex_init: resource No. 43
[22]pthread_mutex_init: resource No. 44
[PORTABLITY]:WscCreateThread--------------------
 [22]pthread_mutex_init: resource No. 45
[PORTABLITY]:pthread_mutex_init--------------------
 RegistrarSM constructor
[22]pthread_cond_init: 5
[22]pthread_mutex_init: resource No. 46
[22]pthread_mutex_init: resource No. 47
[PORTABLITY]:WscCreateThread--------------------
 c_devPwd:org:22013026
**************mcp_devPwd:22013026;;
Generated devPwd: X2i▒
in startMonitor....
CInbEap Construction
Sizeof(WSC_NOTIFY_DATA) = -2006371712
---test--sizeof(WSC_NOTIFY_DATA) = 36
[22]pthread_cond_init: 6
[PORTABLITY]:WscCreateEvent--------------------
 Entered udp_open
Socket open successful, sd: -2006371728
Entered udp_open
Socket open successful, sd: -2006371728
Entered udp_bind
Binding successful for socket [-2006371744]
[PORTABLITY]:WscCreateThread--------------------
 In CInbEap::StaticRecvThread
CInbEap::ActualRecvThread Started
Entered udp_read
in startMonitor....
CInbUPnPDev Construction
Entered udp_open
Socket open successful, sd: -2006371728
Entered udp_open
Socket open successful, sd: -2006371728
Entered udp_bind
Binding successful for socket [-2006371744]
CInbUPnPDev StartMonitor
[PORTABLITY]:WscCreateThread--------------------
 MC::SwitchModeOn: Exit
In CInbUPnPDev::StaticUPnPThread
end UPnPCreateMicroStack
Entered udp_read
MC::StartStack: Informing app of mode
-WscCmd::CallbackProc Enqueue done
MC::SwitchModeOn: Done callback
exit wscmain
@@[31]pthread_mutex_unlock: the res is free 34-- -2007564804
WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd

******* MODE: Access Point *******
-@@[28]pthread_mutex_unlock: the res is free 36-- -2007564924
*******p_header->eType:1

Options:
0. Quit
1. Get configured
2. Get configured via push-button
3. Get configured using IEs
Enter selection: ***gp_mc->mp_info->GetSwitchMode():1
mp_info->GetSwitchMode():1:e_currMode:1,,e_targetMode:3
mp_deviceInfo->authTypeFlags:1
mp_deviceInfo->encrTypeFlags:1
********cp_devPwd:22013026*****
mp_deviceInfo->authTypeFlags:1
mp_deviceInfo->encrTypeFlags:1
MC::SetBeaconIE: call to trans->SetBeaconIE() ok
MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
Waiting for Registrar to connect...
WscCmd::unconfig initiated
ActualUIThreadProc: wait q
[reset_802dot1x] wireless module ready
[init_wpa] dot1x_ready[0]=1

AES Key Wrap Test #0 cipher data:
0x a8ba61f 0x47b41281 0xd84bf3ae 0x827b5afb 0x23863e9d 0xe5cfd271
AES Key wrap Test #0 passed
AES Key UnWrap Test #0 returned with clear data:
0x33221100 0x77665544 0xbbaa9988 0xffeeddcc
AES Key UnWrap Test #0 passed

AES Key Wrap Test #1 cipher data:
0x258b7796 0x35a46cae 0x975b2bf9 0xd2ae50c0 0xa1b88a46 0x5d4ed87a
AES Key wrap Test #1 passed
AES Key UnWrap Test #1 returned with clear data:
0x33221100 0x77665544 0xbbaa9988 0xffeeddcc
AES Key UnWrap Test #1 passed

AES Key Wrap Test #2 cipher data:
0xf9c3e864 0xa25b0fce 0x7977e963 0x2a8a8105 0x1e19c893 0xe78a6e7d
AES Key wrap Test #2 passed
AES Key UnWrap Test #2 returned with clear data:
0x33221100 0x77665544 0xbbaa9988 0xffeeddcc
AES Key UnWrap Test #2 passed

AES Key Wrap Test #3 cipher data:
0x26331d03 0x32d3154e 0xc24ef268 0xdc3e7460 0xddc7c6e1 0x935a72ee 0x9114a86b 0xd
AES Key wrap Test #3 passed
AES Key UnWrap Test #3 returned with clear data:
0x33221100 0x77665544 0xbbaa9988 0xffeeddcc 0x 3020100 0x 7060504
AES Key UnWrap Test #3 passed
[reset_802dot1x] 802.1Xv2 ready
upnp_Init: flag=0
SSDP Initialization completed...
GenaInit : event_hook is NULL!!
 • bootloader start, menu, boot params • >>
 Ready Set Value = 0x0511FFA1

 Setup FLASH_CS1_CFG = 0511FFA1

Disable all eth ports!!
=======================================================================
Wireless Gateway WG7005D Loader V0.13 build Sep 17 2007 16:56:36
                    Arcadyan Technology Corporation
=======================================================================
EON EN29LV160AB bottom boot 16-bit mode found

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...123
Yes, Enter command mode ...

[WG7005D Boot]:

======================
 [U] Upload to Flash
 [E] Erase Flash
 [G] Run Runtime Code
 [A] Set MAC Address
 [#] Set Serial Number
 [V] Set Board Version
 [H] Set Options
 [P] Print Boot Params
 [1] Set SKU Number
 [2] Set PIN Number
======================

[WG7005D Boot]:p

MAC address     : 00-1C-DF-E5-FA-25
Serial number   : 12834923110139
Hardware version: 01
Options         : FF-FF-FF-FF-FF-FF
Country region  : 1
SKU Num         : 1
PIN Num         : 22013026