Belkin F9K1015 v1

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Belkin F9K1015 v1
Availability: now

Manuf (OEM/ODM): Edimax

FCC approval date: 18 February 2014
(Est.) release date: 07 May 2014
Country of manuf.: China

Amazon image

ASIN
B00K6HKJKI (Flag of the United States.svg, On Amazon, On CCC)

Type: range extender

FCC ID: K7SF9K1015V1

Power: 100-240 VAC ~ 50-60 Hz, 0.15 A
Connector type: NEMA 1-15P

CPU1: Realtek RTL8196EU (380 MHz)
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Macronix MX25L3206E)
RAM1: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (Brand? Model?)

Expansion IFs: none specified
Serial: yes, 4-pin header, internal

WI1 chip1: Realtek RTL8192ER
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none

ETH chip1: Realtek RTL8196EU
LAN speed: 0

bgn

Flags: wall-mount

802dot11 OUI: none specified

For a list of all currently documented Realtek chipsets with specifications, see Realtek.


N300 Wall-Mount Wi-Fi Range Extender

"1244-01000930-50Z" is silkscreened on the board in the FCC photos.

Serial

Collected Info

Boot Log
Booting...

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0c22016h 00000c2h 0000020h 0000016h 0000000h 0000016h 0400000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000040h 0001000h 0000400h 0000100h 0000010h 0000027h MX25L3205D
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

---RealTek(RTL8196E)at 2013.11.21-12:29+0800 v1.2 [16bit](380MHz)
no rootfs signature at 000E0000!
no rootfs signature at 000B0000!
no rootfs signature at 000F0000!
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
start address: 0x80003480
CPU revision is: 0000cd01
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,38400 root=/dev/mtdblock1
icache: 16kB/16B, dcache: 8kB/16B, scache: 0kB/0B
NR_IRQS:48
PID hash table entries: 128 (order: 7, 512 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26532k/32768k available (2302k kernel code, 6236k reserved, 511k data, 96k init, 0k highmem)
Calibrating delay loop... 379.28 BogoMIPS (lpj=1896448)
Mount-cache hash table entries: 512
net_namespace: 324 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 51
io scheduler noop registered
io scheduler cfq registered (default)
Realtek GPIO Driver for Flash Reload Default
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 8) is a 16550A
Realtek WLAN driver - version 1.6 (2013-02-21)
Adaptivity function - version 7.1
 wlan_index:0  0, 6,0xb9000000,0xb8b10000,11

=====>>INSIDE rtl8192cd_init_one <<=====
PCIE reset (0)
Do MDIO_RESET
Find Port=0 Device:Vendor ID=818b10ec
vendor_deivce_id=818b10ec
HalAssociateNic OK

#######################################################
SKB_BUF_SIZE=2408 MAX_SKB_NUM=400
#######################################################

=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
<rtl8192cd_init_one>LZQ: after read tmpReg[0x1c]

Probing RTL8186 10/100 NIC-kenel stack size order[3]...
chip name: 8196C, chip revid: 0
NOT YET
eth0 added. vid=9 Member port 0x10...
eth1 added. vid=8 Member port 0x0...
eth2 added. vid=9 Member port 0x2...
eth3 added. vid=9 Member port 0x4...
eth4 added. vid=9 Member port 0x8...
[peth0] added, mapping to [eth1]...

SPI INIT
 ------------------------- Force into Single IO Mode ------------------------
|No chipID  Sft chipSize blkSize secSize pageSize sdCk opCk      chipName    |
| 0 c22016h  0h  400000h  10000h   1000h     100h   50    0        MX25L3206E|
 ----------------------------------------------------------------------------
SPI flash (MX25L3206E) was found at CS0, size 0x400000
Creating 2 MTD partitions on "flash_bank_1":
0x000000000000-0x000000400000 : "boot+cfg+linux"
0x000000130000-0x000000400000 : "root fs"
TCP cubic registered
NET: Registered protocol family 17
dnshijack
VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
Freeing unused kernel memory: 96k freed

init started: BusyBox v1.11.1 (2015-02-11 11:42:19 CST)
starting pid 13, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console.
starting pid 15, tty '': '-/bin/sh'

BusyBox v1.11.1 (2015-02-11 11:42:19 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

ifconfig: ioctl 0x8913 failed: No such device
bridge br0 doesn't exist; can't delete it
ifconfig: ioctl 0x8913 failed: No such device
bridge br2 doesn't exist; can't delete it
InitPON OK
InitMAC OK
InitHCIDMAReg OK
phy_BB88XX_Config_ParaFile(6227), HAL PHY_ConfigBBWithParaFile
[PHY_ConfigBBWithParaFile][PHY_REG_HAL]
[PHY_ConfigBBWithParaFile][PHY_REG_PG_HAL]
[PHY_ConfigBBWithParaFile][AGC_TAB_HAL]
[phy_RF6052_Config_ParaFile][RadioA_HAL]
[phy_RF6052_Config_ParaFile][RadioB_HAL]
InitDownload FW OK
[PHY_ConfigTXPwrTrackingWithParaFile][REG_TXPWR_TRK_8192E]
8192E LCK done!!
wlan_scan command: wlan0 scanssid I Love Pilastra
Use VXD for repeater mode, Disable TXBF
StopHW Succeed
InitPON OK
InitMAC OK
InitHCIDMAReg OK
phy_BB88XX_Config_ParaFile(6227), HAL PHY_ConfigBBWithParaFile
[PHY_ConfigBBWithParaFile][PHY_REG_HAL]
[PHY_ConfigBBWithParaFile][PHY_REG_PG_HAL]
[PHY_ConfigBBWithParaFile][AGC_TAB_HAL]
[phy_RF6052_Config_ParaFile][RadioA_HAL]
[phy_RF6052_Config_ParaFile][RadioB_HAL]
InitDownload FW OK
[PHY_ConfigTXPwrTrackingWithParaFile][REG_TXPWR_TRK_8192E]
8192E LCK done!!
device eth0 entered promiscuous mode
device wlan0 entered promiscuous mode
device wlan0-vxd entered promiscuous mode
br0: port 3(wlan0-vxd) entering forwarding state
br0: port 2(wlan0) entering forwarding state
br0: port 1(eth0) entering forwarding state
dns_hijack_enabled = 1
udhcpc (v1.11.1) started
MemFree:           19692 kB
addcgiext .lua,.lp,.php
axhttpd/1.4.9: listening on ports 80 (http) and 443 (https)
boa: server version Boa/0.94.14rc21
boa: server built Feb 11 2015 at 11:41:55.
boa: starting server pid=289, port 80
# Notice: caching turned off