Dell Wireless 2350 (WRTA-108GD)
Availability: EoL
Manuf (OEM/ODM): Gemtek WRTA-108GD
FCC approval date: 15 August 2004
Country of manuf.: Taiwan
Power: 12 VDC, 0.5 A
Connector type: barrel
Conn. measurements: 5 mm (OD), 2.3 mm (ID), 9.5 mm (LEN)
CPU1: Atheros AR2313A
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Macronix MX29LV320ABTC-90G)
RAM1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (GLT GLT5640L16-6TC)
Expansion IFs: none specified
Serial: yes, internal, 9-pin header, Gemtek type1 pinout, unpopulated, 3.3V TTL, (9600 8N1), JP1
WI1 chip1: Atheros AR2313A
WI1 chip2: Atheros AR2112A
WI1 802dot11 protocols: bg
WI1 antenna connector: none
ETH chip1: Atheros AR2313A
Switch: Marvell 88E6060
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1
Stock FW OS: VxWorks OpenRG
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
Dell Wireless 2350 Broadband Router
"WRTA-108GD_V02" and "109-102-3401" is silkscreened on the board pictured below.
Links
Models
Probable included PSU(s)
The pTrans WD411200500 was included with at least some of these devices.
- FCC docs indicate that the Delta Electronics ADP-10SB Rev. B
- may have bee included with other units (maybe).
pTrans WD411200500 (110-100-0095) (more)
|
Input: 120 VAC ~ 50 Hz, 0.1 A
|
Input connector: NEMA 1-15P Style: large, vertical Manuf. in: China
|
Output: 12 VDC, 0.5 A
|
Output connector: barrel (center +) OD: 5 mm ID: 2.3 mm LEN: 9.5 mm
|
Serial
Pinout
JP1
( ) (TxD) ( ) ( ) (RxD)
(3.3) (3.3) (GND) (GND)
Credentials
They're the default Atheros AP credentials.
Username: Admin
Password: 5up
Boot log
Expand • boot log • >>
|
ar531x rev 0x00005850 firmware startup...
SDRAM TEST...PASSED
Atheros AR5001AP default version 3.4.0.29
auto-booting...
Attaching to TFFS... done.
Loading /fl/APIMG1...18920 + 1488320 + 105600
Starting at 0x804846e0...
/fl/ - Volume is OK
Reading Configuration File "/fl/apcfg".
Configuration file checksum: 44e94 is good
Please check the ethernet cable on port 1!
Attaching interface lo0...done
**********************************************************
* Initializing Jungo OpenRG *
**********************************************************
wireless access point starting...
0x80649510 (openrg): loading license key: Dell
0x80649510 (openrg): Device lmr0 initialized
sock_set_sockopt 0: failed setting non-blocking
0x80649510 (openrg): rtinit: wrong ifa (807c1674) was (807c114c)
0x80649510 (openrg): rtinit: wrong ifa (807c1ca4) was (807c1c20)
0x80649510 (openrg): STP: vp256 enters blocking mode
0x80649510 (openrg): rtinit: wrong ifa (807c1ca4) was (807c1c20)
Start Main() Lizzy mt_tony Ver is V2.8
Set_nvram(system/network/,initial_setup,1)
Get_nvram(dev/br0/static/,ip)=192.168.2.1
Listen packet start
Auto Channel Scan selected 2412 MHz, channel 1
wlan1 Ready
Ready
0x80633f70 (nashaTaska): STP: vp256 exits blocking mode
|
Shell
Expand • help
|
wlan1 - ?
List of Access Point CLI commands:
config wlan -- config wlanX
connect bss -- connect to bssX
del acl -- Delete Access Control List
del key -- Delete Encryption key
find bss -- Find BSS
find channel -- Find Available Channel
find all -- Find All BSS
ftp -- Software update via FTP
get 11gonly -- Display 11g Only Allowed
get 11goptimize -- Display 11g Optimization Level
get 11goverlapbss -- Display Overlapping BSS Protection
get acl -- Display Access Control List
get aging -- Display Aging Interval
get antenna -- Display Antenna Diversity
get association -- Display Association Table
get authentication -- Display Authentication Type
get autochannelselect -- Display Auto Channel Select
get beaconinterval -- Display Beacon Interval
get burstSeqThreshold -- Display Max Number of frames in a Burst
get burstTime -- Display Burst Time
get channel -- Display Radio Channel
get cipher -- Display Encryption cipher
get config -- Display Current AP Configuration
get countrycode -- Display Country Code
get ctsmode -- Display CTS mode
get ctsrate -- Display CTS rate
get ctstype -- Display CTS type
get domainsuffix -- Display Domain Name Server suffix
get dtim -- Display Data Beacon Rate (DTIM)
get encryption -- Display Encryption Mode
get extendedchanmode -- Display Extended Channel Mode
get fragmentthreshold -- Display Fragment Threshold
get frequency -- Display Radio Frequency (MHz)
get gateway -- Display Gateway IP Address
get groupkeyupdate -- Display Group Key Update Interval (in Seconds)
get hardware -- Display Hardware Revisions
get hostipaddr -- Display Host IP Address
get ipaddr -- Display IP Address
get ipmask -- Display IP Subnet Mask
get key -- Display Encryption Key
get keyentrymethod -- Display Encyrption Key Entry Method
get keysource -- Display Source Of Encryption Keys
get login -- Display Login User Name
get minimumrate -- Display Minimum Rate
get nameaddr -- Display IP address of name server
get operationMode -- Display Operation Mode
get pktLogEnable -- Display Packet Logging Mode
get power -- Display Transmit Power Setting
get radiusname -- Display RADIUS server name or IP address
get radiusport -- Display RADIUS port number
get rate -- Display Data Rate
get remoteAp -- Display Remote Ap's Mac Address
get rtsthreshold -- Display RTS/CTS Threshold
get shortpreamble -- Display Short Preamble Usage
get shortslottime -- Display Short Slot Time Usage
get sntpserver -- Display SNTP/NTP Server IP Address
get ssid -- Display Service Set ID
get ssidsuppress -- Display SSID Suppress Mode
get station -- Display Station Status
get SuperG -- Display SuperG Feature Status
get systemname -- Display Access Point System Name
get tzone -- Display Time Zone Setting
get uptime -- Display UpTime
get wirelessmode -- Display Wireless LAN Mode
get wlanstate -- Display wlan state
help -- Display CLI Command List
ping -- Ping
pktLog -- Packet Log
reboot -- Reboot Access Point
run -- Run command file
quit -- Logoff
set 11gonly -- Set 11g Only Allowed
set 11goptimize -- Set 11g Optimization Level
set 11goverlapbss -- Set Overlapping BSS Protection
set acl -- Set Access Control List
set aging -- Set Aging Interval
set antenna -- Set Antenna
set authentication -- Set Authentication Type
set autochannelselect -- Set Auto Channel Selection
set beaconinterval -- Modify Beacon Interval
set burstSeqThreshold -- Set Max Number of frames in a Burst
set burstTime -- Set Burst Time
set channel -- Set Radio Channel
set cipher -- Set Cipher
set countrycode -- Set Country Code
set ctsmode -- Set CTS Mode
set ctsrate -- Set CTS Rate
set ctstype -- Set CTS Type
set domainsuffix -- Set Domain Name Server Suffix
set dtim -- Set Data Beacon Rate (DTIM)
set encryption -- Set Encryption Mode
set extendedchanmode -- Set Extended Channel Mode
set factorydefault -- Restore to Default Factory Settings
set fragmentthreshold -- Set Fragment Threshold
set frequency -- Set Radio Frequency (MHz)
set gateway -- Set Gateway IP Address
set groupkeyupdate -- Set Group Key Update Interval (in Seconds)
set hostipaddr -- Set Host IP address
set ipaddr -- Set IP Address
set ipmask -- Set IP Subnet Mask
set key -- Set Encryption Key
set keyentrymethod -- Select Encryption Key Entry Method
set keysource -- Select Source Of Encryption Keys
set login -- Modify Login User Name
set minimumrate -- Set Minimum Rate
set nameaddress -- Set Name Server IP address
set operationMode -- Set operation Mode
set password -- Modify Password
set passphrase -- Modify Passphrase
set pktLogEnable -- Enable Packet Logging
set power -- Set Transmit Power
set radiusname -- Set RADIUS name or IP address
set radiusport -- Set RADIUS port number
set radiussecret -- Set RADIUS shared secret
set rate -- Set Data Rate
set remoteAP -- Set Remote AP's Mac Address
set rtsthreshold -- Set RTS/CTS Threshold
set shortpreamble -- Set Short Preamble
set shortslottime -- Set Short Slot Time
set sntpserver -- Set SNTP/NTP Server IP Address
set ssid -- Set Service Set ID
set ssidsuppress -- Set SSID Suppress Mode
set SuperG -- Super G Features
set systemname -- Set Access Point System Name
set tzone -- Set Time Zone Setting
set wlanstate -- Set wlan state
set wirelessmode -- Set Wireless LAN Mode
timeofday -- Display Current Time of Day
version -- Software version
rg_cli -- Start OpenRG CLI
|
Expand • get hardware
|
wlan1 - get hardware
wlan1 revisions: mac 5.8 phy 4.4 analog 4.6
PCI Vendor ID: 0x168c, Device ID: 0x13
Sub Vendor ID: 0x168c, Sub Device ID: 0x13
chip is AR2312
|
Expand • version
|
wlan1 - version
AP software 3.4.0.29
openrg@openrg:ar531x
Oct 9 2004, 02:58:06
|
Expand • rg_cli help
|
wlan1 - rg_cli
OpenRG help
CLI Commands
exit Exit from the current cli
die <ret>
Exit from OpenRG and return ret
ps Print OpenRG's tasks
rg_conf_print <root>
Print OpenRG configuration starting from root - use / for
the whole configuration
rg_conf_set <path> <value>
Set OpenRG configuration path to value
rg_conf_set_obscure <path> <value>
Set OpenRG configuration path to an obscured value
rg_conf_del <path>
Delete subtree beginning at path from OpenRG configuration
rg_conf_ram_set <path> <value>
Set OpenRG dynamic configuration path to value
rg_conf_ram_print <root>
Print OpenRG's dynamic configuration starting from root -
use / for the whole configuration
reconf <flash_delay 1(=NOW) to 4>
Reconfigure the system according to the current OpenRG
configuration
entity_close <entity_ptr>
Close an entity
host <name>
Resolve host by name
fw_restart Stop & Start Firewall & NAT
fw_start Activate Firewall & NAT
fw_stop Deactivate Firewall & NAT
fw_filter 0 - NAT only, 1 - NAT+filter
mac_cache_dump
fw_dump [-v] [-ah|-hi] [-c chain | -h address | -i index] [-pr|-ps|-ph|-pm|-pd|-pp]
Display firewall rule tree
fw_variable [-v] [-a] [-i index | -n name]
Display variables of the firewall rules
fw_trace Usage: fw_trace <code> - where code is 0 (off), 1 (full),
2 (partial).
flash_commit Save OpenRG configuration to flash
restore_default [-d] to avoid rebooting after
Restore default configuration
reboot Reboot the system
log_lev_on <severity>
Redirect rg_error output equal to or higher than severity
to the current console.
Severity level values
are:
0: Prints debugging messages.
1: Prints
informational messages.
2: Prints warning
messages.
3: Prints error messages.
4: Prints fatal
error messages.
5: Prints fatal error messages and
reboots OpenRG.
log_lev_off Stop rg_error redirection to the current console
rmt_upd Remotely upgrade the box
rmt_upd_wget_close Kill a remote upgrade process
rg_ifconfig <details_level>
print_main_wan Print the name of the current main wan device
cat_log [fw|varlog] | e[#buf_num]
Print contents of log to console
bridge_info Print bridge information
flash_layout Print the flash layout and content
flash_erase [-d] <section>
Erase a given section in the flash
flash_dump [-s section | -r address] [-l length] [-1|2|4]
Dump the flash content
bset Configure bootloader
ifconfig Configure network interface
ping <ip>
Test network connectivity
route Print route table
load [-u url] [-s section | -r address]
Load and burn image
ver Display version information
etask_list_dump Dump back trace of all etasks
sys_ioctl <char_device_type> <command>
issue openrg ioctl
help [category] to list commands in a category
Print a list of command categories
Returned 0
|
Expand • rg_cli, ver
|
OpenRG ver
Version: 3.14.14.1.23.18.2
Platform: Atheros AR531x
Compilation Time: Sat Oct 9 2004 02:54:41
Compilation Flags: DIST=AR2313_LIZZY
Returned 0
|
Expand • rg_cli, flash_layout
|
OpenRG flash_layout
Flash layout:
Section 00 Type IMAGE Range 0x00000000-0x002E8000 MaxSize 0x002E7F6C
Size 0x00186B9A Name 'Downloaded at: WED JAN 01 00:07:17 2003'
Checksum 0x0C5D8D8E Counter 0x00000013 Start Offset 0x00000000
Section 01 Type CONF Range 0x002E8000-0x002F0000 MaxSize 0x00007F6C
Size 0x000015E9 Name 'rg_conf'
Checksum 0x000AE8EF Counter 0x00000319 Start Offset 0x00000000
Section 02 Type CONF Range 0x002F0000-0x002F8000 MaxSize 0x00007F6C
Size 0x000015A9 Name 'rg_conf'
Checksum 0x000AD3A9 Counter 0x00000311 Start Offset 0x00000000
Section 03 Type FACTORY Range 0x002F8000-0x002F9000 MaxSize 0x00000F6C
Size 0x0000027B Name 'rg_factory'
Checksum 0x0000A406 Counter 0x00000023 Start Offset 0x00000000
Total 4 sections found.
Returned 0
|
Expand • rg_cli, ps
|
OpenRG ps
OpenRG PS:
Entities:
eid=0x80585500 type=ENT_WDS t=0x1b ent_status=0x0 next=0x80585530
eid=0x80585530 type=ENT_URL_KEYWORD_FILTER t=0x0 ent_status=0x0 next=0x80585580
eid=0x80585580 type=(null) t=0x0 ent_status=0x0 next=0x805855f0
eid=0x805855f0 type=ENT_HTTP_PROXY t=0x0 ent_status=0x805855d0 next=0x80585680
eid=0x80585680 type=ENT_RMT_UPD t=0x0 ent_status=0x80585650 next=0x80585790
eid=0x80585790 type=ENT_CLI_SERVER t=0x80585760 ent_status=0x0 next=0x80597000
eid=0x80597000 type=ENT_DHCPS t=0x80596fb0 ent_status=0x805dd730 next=0x805dda80
eid=0x805dda80 type=ENT_RMT_MNG_SERVER t=0x0 ent_status=0x805dda60 next=0x805ddbf0
eid=0x805ddbf0 type=ENT_RMT_MNG_SERVER t=0x0 ent_status=0x805ddbd0 next=0x805dde90
eid=0x805dde90 type=ENT_SSI t=0x805dde60 ent_status=0x805ddef0 next=0x805de020
eid=0x805de020 type=ENT_SSI_RMT_UPD_CGI t=0x805ddfc0 ent_status=0x805ddf10 next=0x805de360
eid=0x805de360 type=ENT_HTTPS t=0x805de2c0 ent_status=0x0 next=0x805de4f0
eid=0x805de4f0 type=ENT_TELNET_MASTER_SERVER t=0x0 ent_status=0x805de4d0 next=0x805de560
eid=0x805de560 type=ENT_ROUTE t=0x0 ent_status=0x805de540 next=0x805de650
eid=0x805de650 type=ENT_TODC t=0x0 ent_status=0x805de600 next=0x805de6a0
eid=0x805de6a0 type=ENT_RIP t=0x0 ent_status=0x0 next=0x805de8a0
eid=0x805de8a0 type=ENT_IGD t=0x805de860 ent_status=0x805de880 next=0x805df9d0
eid=0x805df9d0 type=ENT_KLOG t=0x805df9b0 ent_status=0x0 next=0x805e5210
eid=0x805e5210 type=ENT_SYSLOG t=0x805e5140 ent_status=0x805e51d0 next=0x805e5240
eid=0x805e5240 type=ENT_LOGIN t=0x0 ent_status=0x0 next=0x805e52c0
eid=0x805e52c0 type=ENT_DDNS t=0x0 ent_status=0x0 next=0x805e53c0
eid=0x805e53c0 type=ENT_ENTFY t=0x0 ent_status=0x805e53a0 next=0x80289848
eid=0x80289848 type=ENT_FW_RESOLV t=0x0 ent_status=0x0 next=0x802897dc
eid=0x802897dc type=ENT_FIREWALL t=0x0 ent_status=0x805e5980 next=0x805ae200
eid=0x805ae200 type=ENT_ERESOLV t=0x0 ent_status=0x0 next=0x805af520
eid=0x805af520 type=ENT_DNS t=0x805e5ad0 ent_status=0x0 next=0x805af900
eid=0x805af900 type=ENT_TIME t=0x0 ent_status=0x805e5d40 next=0x0
Devices:
name=br0 type=Bridge
eid=0x80597000 type=ENT_DHCPS t=0x80596fb0 ent_status=0x805dd730 next=0x805dda80
name=ae3 type=Ethernet
eid=0x80595c30 type=ENT_DHCPC t=0x805962f0 ent_status=0x80595c10 next=0x0
name=ae2 type=Ethernet
name=vp256 type=Wireless 802.11g Access Point
name=ppp0 type=PPPoE
Returned 0
|
Images