Edimax EW-7206APg v4
Availability: OEM, unknown
FCC approval date: 30 May 2007
Type: access point, repeater, bridge
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: Realtek RTL8186 (180 MHz)
FLA1: 2 MiB 2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Macronix MX29LV160CBTC-70G)
RAM1: 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Mira P2V64S40ETP-G6)
Expansion IFs: none specified
WI1 chip1: Realtek RTL8186
WI1 chip2: Realtek RTL8225
WI1 802dot11 protocols: bg
WI1 antenna connector: RP-SMA
ETH chip1: Realtek RTL8186
ETH chip2: Realtek RTL8201CP
LAN speed: 100M
LAN ports: 1
Additional chips
2.4GHz Power Amplifier IC;Microchip;SST12LP14A;SST, 12LP14A, 825112;1;InGaP/GaAs;QFN-16;3 mm x 3 mm;
Stock bootloader: rtkload v1.3c
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Product page
"1242-00000263-01Z" is silkscreened on the board.
The FCC test report lists the following as identical models..
- Edimax EW-7206APg / GAP-E06G
- LevelOne WAP-0006
- Longshine LCS-WA5-40
- Hawking HWREG1 / HWBA54G
- MINITAR MNWAPG
- TONZE AW-6200R
- PheeNet WAP-554G
- JAHT WP-4001BR
- Conceptronic C54APM
- Intellinet 501903
- Asbis CN-WFAP
- Sandberg 131-01
- 2 Direct WL0027
- Planet WAP-4033
- Micronet SP918GKV5
Images
External
Internal
Serial
Pinout
Info derived from
These serial logs are from the Intellinet branded unit shown above.
Expand • boot log
|
UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory
---RealTek(RTL8186)at 2005.06.06-11:22+0800 version 1.3c [16bit](180MHz)
Jump to image start=0x80300000...
display on
entering boot loader, turning on display
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 00800000 @ 00000000 (usable)
Initial ramdisk at: 0x80196000 (634880 bytes)
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 178.99 BogoMIPS
Memory: 5660k/8192k available (1419k kernel code, 2532k reserved, 760k data, 48k init, 0k highmem)
Dentry-cache hash table entries: 1024 (order: 1, 8192 bytes)
Inode-cache hash table entries: 512 (order: 0, 4096 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 2048 (order: 1, 8192 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
HDLC support module revision 1.02 for Linux 2.4
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
RTL8185 driver version 1.11 (2006-08-01)
8186NIC Ethernet driver v0.0.2 (Jan 30, 2004)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 618 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 620k freed
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
serial console detected. Disabling virtual terminals.
BusyBox v1.00-pre8 (2005.11.23-10:23+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
Sat Jan 1 00:00:00 UTC 2000
create flash.inc
Initialize WLAN interface
Interface doesn't accept private ioctl...
set_mib (89F1): Operation not permitted
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
eth0:phy is 8201
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
br0: port 2(wlan0) entering listening state
br0: port 1(eth0) entering listening state
br0: port 2(wlan0) entering learning state
br0: port 2(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
********** run Diagd **********
setting: port: 31727
running in daemon mode
********** run GaTest **********
IEEE 802.11f (IAPP) using interface br0 (v1.6)
Please enter your Name and Password
User Name :
-------------------------------------------------------------------------------
<TAB> Select <ESC> Exit <Enter> Enter
|