Inteno DG150B

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Inteno DG150B v1
Availability: Discontinued

Country of manuf.: China

Type: wireless router, dsl modem, analog phone gateway, CPE

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: Broadcom BCM6361V (400 MHz, 2 cores)
FLA1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Spansion S34ML01G100TFI00)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Micron Model?)

Expansion IFs: none specified
Serial: yes, 4-pin header, 3.3V TTL, (115200 8N1), J304

WI1 chip1: Broadcom BCM6361V
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none

ETH chip1: Broadcom BCM6361V
Switch: Broadcom BCM6361V
LAN speed: 100M
LAN ports: 4
WAN speed: 1GbE
WAN ports: 1

bgn

Additional chips
Single-Chip ProSLIC (FXS);Silicon Labs;Si32176;;1;

Stock bootloader: CFE 1.0.38-114.185 BCM6361

Stock FW OS: Linux 2.6.30

Flags: ADSL2+, VoIP

Default IP address: 10.0.0.1
the IP 10.0.0.1 is used by 21 additional devices
of which 0 are Inteno devices
Default login user: user
Default login password: user
user:user credentials used by 9 additional devices
of which 0 are Inteno devices

802dot11 OUI: 00:22:07
Ethernet OUI: 00:22:07

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.


Gigabit Residential Gateway

Product page (NO)
  • The CPU on the board is part Broadcom BCM6361VKFEBG

Serial

Boot log

 • bootlog • >>
HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
300H
PHYE
DINT
LASY
USYN
MSYN
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
FPS0
BT58
0001
BT59
0492
NAN3
RFS2
NAN5


CFE version 1.0.38-114.185 for BCM96362 (32bit,SP,BE)
Build Date: Fri Apr 22 11:09:42 CST 2016 (chris_chiu@cs1)
Copyright (C) 2000-2011 Broadcom Corporation.

NAND flash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB
Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-13)                   : 96362ADVNgr
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 00:22:07:32:a1:9c
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1]          : 0
Voice Board Configuration (0-13)  : SI32176

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1�1�0
Booting from latest image (0xbbd80000) ...
Decompression OK!
Entry at 0x8032af00
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x8032af00
Linux version 2.6.30 (chris_chiu@cs1) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Fri Apr 22 11:12:54 CST 2016

BCM Flash API. Flash device is not found.

96362ADVNgr prom init

CPU revision is: 0002a070 (Broadcom4350)

DSL SDRAM reserved: 0x100000

Determined physical RAM map:

 memory: 07f00000 @ 00000000 (usable)

Zone PFN ranges:

  DMA      0x00000000 -> 0x00001000

  Normal   0x00001000 -> 0x00007f00

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0: 0x00000000 -> 0x00007f00

On node 0 totalpages: 32512

free_area_init_node: node 0, pgdat 803fcef0, node_mem_map 81000000

  DMA zone: 32 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 4064 pages, LIFO batch:0

  Normal zone: 222 pages used for memmap

  Normal zone: 28194 pages, LIFO batch:7

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32258

Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200

wait instruction: enabled

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

NR_IRQS:128

PID hash table entries: 512 (order: 9, 2048 bytes)

console [ttyS0] enabled

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Allocating memory for DSP module core and initialization code

Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0

Memory: 124204k/130048k available (3212k kernel code, 5656k reserved, 825k data, 152k init, 0k highmem)

Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)

Mount-cache hash table entries: 512

--Kernel Config--

  SMP=1

  PREEMPT=1

  DEBUG_SPINLOCK=0

  DEBUG_MUTEXES=0

Broadcom Logger v0.1 Apr 22 2016 11:10:16

CPU revision is: 0002a070 (Broadcom4350)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)

Brought up 2 CPUs

net_namespace: 1140 bytes

NET: Registered protocol family 16

Total Flash size: 0K with -1 sectors

registering PCI controller with io_map_base unset

registering PCI controller with io_map_base unset

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]

pci 0000:00:00.0: supports D1 D2

pci 0000:00:00.0: PME# supported from D0 D3hot D3cold

pci 0000:00:00.0: PME# disabled

pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]

pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]

pci 0000:01:00.0: PME# supported from D0 D3hot

pci 0000:01:00.0: PME# disabled

pci 0000:01:00.0: PCI bridge, secondary bus 0000:02

pci 0000:01:00.0:   IO window: disabled

pci 0000:01:00.0:   MEM window: disabled

pci 0000:01:00.0:   PREFETCH window: disabled

PCI: Setting latency timer of device 0000:01:00.0 to 64

skbFreeTask created successfully

�[0;34mBLOG v3.0 Initialized�[0m

BLOG Rule v1.0 Initialized

Broadcom IQoS v0.1 Apr 22 2016 11:12:27 initialized

Broadcom GBPM v0.1 Apr 22 2016 11:12:27 initialized

NET: Registered protocol family 8

NET: Registered protocol family 20

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

fuse init (API version 7.11)

msgmni has been set to 242

io scheduler noop registered (default)

PCI: Setting latency timer of device 0000:01:00.0 to 64

Driver 'sd' needs updating - please use bus_type methods

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

bcm963xx_mtd driver v2.0

Failed to read image tag from flash

Broadcom DSL NAND controller (BrcmNand Controller)

-->brcmnand_scan: CS=0, numchips=1, csi=0

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

Disabling XOR on CS#0

brcmnand_scan: Calling brcmnand_probe for CS=0

B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=01f1001d

After: NandSelect=40000001, nandConfig=15142200

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff

timing1 not adjusted: 5363444f

timing2 not adjusted: 00000fc6

BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0


Found NAND on CS0: ACC=f3000000, cfg=15142200, flashId=01f1001d, tim1=5363444f, tim2=00000fc6

BrcmNAND version = 0x0202 128MB @00000000

B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=01f1001d

After: NandSelect=40000001, nandConfig=15142200

Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0

brcmnand_scan: Done brcmnand_probe

brcmnand_scan: B4 nand_select = 40000001

brcmnand_scan: After nand_select = 40000001

brcmnand_scan 10

200 CS=0, chip->ctrl->CS[0]=0

200 chip->ecclevel=15, acc=f3000000

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

brcmnand_scan 220

Brcm NAND controller version = 2.2 NAND flash size 128MB @18000000

brcmnand_scan 230

brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000

brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0

ECC layout=brcmnand_oob_bch4_4k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsize=512, writesize=2048

brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3

300 CS=0, chip->ctrl->CS[0]=0

500 chip=87a40190, CS=0, chip->ctrl->CS[0]=0

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0

Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0

brcmnandCET: Status -> Deferred

brcmnand_scan 99

Creating 4 MTD partitions on "brcmnand.0":

0x000003d80000-0x000007ae0000 : "rootfs"

0x000000020000-0x000003d80000 : "rootfs_update"

0x000007b00000-0x000007f00000 : "data"

0x000000000000-0x000000020000 : "nvram"

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)

PCI: Setting latency timer of device 0000:00:0a.0 to 64

ehci_hcd 0000:00:0a.0: EHCI Host Controller

ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1

ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM

ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500

ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

PCI: Enabling device 0000:00:09.0 (0000 -> 0002)

PCI: Setting latency timer of device 0000:00:09.0 to 64

ohci_hcd 0000:00:09.0: OHCI Host Controller

ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2

ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

usbcore: registered new interface driver usblp

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

brcmboard: brcm_board_init entry

kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected

kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected

kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected

kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected

SES: LED GPIO 0xc00c is enabled

PCIe: No device found - Powering down

Serial: BCM63XX driver $Revision: 3.00 $

�[0;33mMagic SysRq enabled (type ^ h for list of supported commands)�[0m

ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX

ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX

Total # RxBds=2740

bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized


bcmPktDma_init: Broadcom Packet DMA Library initialized

bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Apr 22 2016 11:12:09

IPSEC SPU: SUCCEEDED

GACT probability NOT on

Mirror/redirect action on

u32 classifier

    input device check on

    Actions configured

TCP cubic registered

Initializing XFRM netlink socket

NET: Registered protocol family 10

IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

NET: Registered protocol family 15

Initializing MCPD Module

Ebtables v2.0 registered

ebt_time registered

ebt_ftos registered

ebt_wmm_mark registered

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (jffs2 filesystem) readonly on device 31:0.

Freeing unused kernel memory: 152k freed


init started: BusyBox v1.17.2 (2016-04-22 11:15:29 CST)

starting pid 221, tty '': '/etc/init.d/rcS'

starting pid 225, tty '': '-/bin/sh'


BusyBox v1.17.2 (2016-04-22 11:15:29 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

chipinfo: module license 'proprietary' taints kernel.

Disabling lock debugging due to kernel taint

brcmchipinfo: brcm_chipinfo_init entry

Broadcom Ingress QoS Module  Char Driver v0.1 Apr 22 2016 11:11:50 Registered<243>�[0m


Broadcom Ingress QoS ver 0.1 initialized

BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128

Broadcom BPM Module Char Driver v0.1 Apr 22 2016 11:10:46 Registered<244>�[0m

�[0;34m[NTC bpm] bpm_set_status: BPM status : enabled

�[0m

NBUFF v1.0 Initialized

�[0;36;44mInitialized fcache state�[0m

�[0;36;44mBroadcom Packet Flow Cache  Char Driver v2.2 Apr 22 2016 11:11:50 Registered<242>�[0m

Created Proc FS /procfs/fcache

�[0;36;44mBroadcom Packet Flow Cache registered with netdev chain�[0m

�[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.�[0m

�[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 Apr 22 2016 11:11:50�[0m

chipId 0x636220B0

Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 22 2016 11:11:45 Registered <241>

Enabling SMISBUS PHYS_FAP_BASE[0] is 0x14001000

FAP Soft Reset Done

4ke Reset Done

FAP Debug values at 0xa5d9c590 0xa5d9c590

Allocated FAP0 GSO Buffers (0xA5DAD618) : 1048576 bytes @ 0xA5E00000

Allocated FAP0 TM SDRAM Queue Storage (a5dad61c) : 341376 bytes @ a5f00000

�[0;34m[NTC fapProto] fapReset  : Reset FAP Protocol layer�[0m

[FAP0] DSPRAM : stack <0x80004000><1536>, global <0x80004600><3864>, free <2792>, total<8192>

[FAP0] PSM : addr<0xE0010000>, used <24216>, free <8552>, total <32768>

[FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004600

[FAP0] GSO Buffer set to 0xA5E00000

[FAP0] FAP BPM Initialized.

fapDrv_construct: FAP0: pManagedMemory=b1010650. wastage 8 bytes

bcmPktDma_bind: FAP Driver binding successfull

[FAP0] FAP TM: ON

bcmxtmcfg: bcmxtmcfg_init entry

adsl: adsl_init entry

Broadcom BCM6362B0 Ethernet Network Device v0.1 Apr 22 2016 11:12:03

fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b1010650 bytes remaining 7000

ETH Init: Ch:0 - 200 tx BDs at 0xb1010650

fapDrv_psmAlloc: wastage 8 bytes

fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b1011910 bytes remaining 2184

ETH Init: Ch:0 - 600 rx BDs at 0xb1011910

ETH Init: Ch:1 - 1892 rx BDs at 0xa7a18000

dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered

eth0: MAC Address: 00:22:07:32:A1:9C

eth1: MAC Address: 00:22:07:32:A1:9C

eth2: MAC Address: 00:22:07:32:A1:9C

eth3: MAC Address: 00:22:07:32:A1:9C

eth4: MAC Address: 00:22:07:32:A1:9C

�[0;34m[NTC arl] arlEnable : Enabled ARL binding to FAP�[0m

Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Apr 22 2016 11:10:46 Registered <245>

--SMP support

wl: dsl_tx_pkt_flush_len=338

wl: high_wmark_tot=6149

PCI: Setting latency timer of device 0000:00:00.0 to 64

wl: passivemode=1

wl: napimode=0

wl0: allocskbmode=1 currallocskbsz=512

Neither SPROM nor OTP has valid image

wl:srom/otp not programmed, using main memory mapped srom info(wombo board)

wl:loading /etc/wlan/bcm6362_map.bin

srom rev:8

wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16

wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.0

dgasp: kerSysRegisterDyingGaspHandler: wl0 registered

Endpoint: endpoint_init entry

Endpoint: endpoint_init COMPLETED

p8021ag: p8021ag_init entry

Broadcom 802.1Q VLAN Interface, v0.1

===== Release Version DG150B_4.12NGT02.54 (build timestamp 160422_1113) =====

ssk:error:22.697:lck_checkBeforeEntry:225:lock reBOS: Enter bosInit

quired during cmBOS: Exit bosInit

sObj_getNextInSuendpoint_open COMPLETED

bTreeFlags
DDR Self Refresh pwrsaving is enabled

Adaptive Voltage Scaling is now enabled

BcmPwrMngtEnableAvs: AVS_START, 0x87acf258

Netfilter messages via NETLINK v0.30.

device eth0 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth0: link is not ready

ip_tables: (C) 2000-2006 Netfilter Core Team

ip6_tables: (C) 2000-2006 Netfilter Core Team

device eth1 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth1: link is not ready

device eth2 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth2: link is not ready

device eth3 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth3: link is not ready

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

WLmngr Daemon is running
optarg=0 shmId=0
wlevt is ready for new msg...
BcmAdsl_Initialize=0xC0263BB0, g_pFnNotifyCallback=0xC0298484

pSdramPHY=0xA7FFFFF8, 0xF7EFF6DF 0xDDDADF7D

*** XfaceOffset: 0x21F90 => 0x21F90 ***

*** PhySdramSize got adjusted: 0x8B980 => 0xA15BC ***

AdslCoreSharedMemInit: shareMemSize=387613(387616)

AdslCoreHwReset:  pLocSbSta=84540000 bkupThreshold=1600

AdslCoreHwReset:  AdslOemDataAddr = 0xA7F80170

***BcmDiagsMgrRegisterClient: 0 ***

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered

fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584

XTM Init: 200 rx BDs at 0xb1012be0

fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456

XTM Init: 16 rx BDs at 0xb1013220

ADDRCONF(NETDEV_UP): eth4: link is not ready

Success
rcl_wanEthIntfObject: ethswctl -c hw-switching -o disable
monitor task is initialized pid= 334 

ssk:error:29.419:initVodslBoundIpIfWanSideUpLocked:766:Failed to get WAN Connection object
ssk:error:29.434:ssk_main:597:cannot handle msg type 0x10000802
There is no Predefined DevicePin in CFE
WPS Device PIN = 49385052
br0: port 5(wl0) entering disabled state

device wl0 left promiscuous mode

br0: port 5(wl0) entering disabled state

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

killall: hspotap: no process killed
br0: port 5(wl0) entering disabled state

Setting SSID: "NextGenTel_9F"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
wlctl: Unsupported
device wl0 left promiscuous mode

br0: port 5(wl0) entering disabled state

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

Note: Loading 6300 MDK (default) driver for 6362 chip 
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0x2f; config_pbmp = 0x2f 
Switch MDK link poll thread: unit=0; phypbmp=0x2f
tr69c:error:34.591:updateTr69cCfgInfo:750:could not build full path to (null)
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1001
600 sec

See also

ModelsDevices
Inteno DG150B • Wi-Fi 4 (Annex B)
Inteno DG301B • Wi-Fi 4

Images