KAONMEDIA DG2200TN
From WikiDevi.Wi-Cat.RU
Jump to navigation
Jump to search
KAONMEDIA DG2200 TN (Telenor)
(Est.) release date: December 2020
Country of manuf.: Indonesia
Series: AC2000
Type: wireless router, dsl modem
Power: 12 VDC, 2.5 A
Connector type: barrel
CPU1: Broadcom BCM63138U (1.0 GHz, 2 cores)
FLA1: 256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (JSC JS27HU2G08SDDA-25)
RAM1: 512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (Samsung K4B4G1646E-BCBN)
Expansion IFs: USB 3.0
USB ports: 1
Serial: yes, 5-pin header, 3.3V TTL, (115200 8N1), J109
WI1 chip1: Broadcom BCM43217T
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: Broadcom BCM4365E
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 4x4:4
WI2 antenna connector: none
ETH chip1: Broadcom BCM63138U
Switch: Broadcom BCM63138U
LAN speed: 1GbE
LAN ports: 4
WAN speed: 1GbE
WAN ports: 1
abgn+ac
Additional chips
xDSL CPE Line Driver w/ On-chi;Broadcom;BCM6303;BCM6303KMLG;1;
Stock bootloader: CFE 1.0.38-118.8 BCM963138
Stock FW OS: Linux 3.4.11-rt19
Flags: ADSL2+, VDSL2
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
Telenor WiFi Ruter
- KAON Media DG2200TN
Models
- KAONMEDIA AR2040 • Range Extender
- KAONMEDIA AR4520 (2018) • Layer3 TV AR4520
- KAONMEDIA CG2001 (2016) • Cable Modem
- KAONMEDIA CG2200 (2018) • Cable Modem
- KAONMEDIA DG2200TN (2020) • Cable Modem
- KAONMEDIA CG3000 (2017) • Cable Modem
- KAONMEDIA VM3000G (2017) • Cable Modem
Serial
Boot log
| Expand • bootlog • >> |
|---|
HELO
CPU0
PMCM
PMCS
PMCD
CODE
L1CD
MMUI
ZBBS
MAIN
4.1605-1.0.38-118.8
DRAM
NVRAM memcfg 0x427
MCB chksum 0xf67f5b05
DDR3-1600 CL11 512MB
Changed Byte Lane LDE
Changed Byte Lane LDE
PASS
FPS0
BT99
0001
BT00
0552
NAN3
RFS2
NAN5
Base: 4.16_05
CFE version 1.0.38-118.8 for BCM963138 (32bit,SP,LE)
Build Date: Wed Nov 21 13:37:51 KST 2018 (nwj99@ubuntu)
Copyright (C) 2000-2015 Broadcom Corporation.
Boot Strap Register: 0x7dfffe2f
Chip ID: BCM63138B0, ARM Cortex A9 Dual Core: 1000MHz
Total Memory: 536870912 bytes (512MB)
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: , id 0xadda block 128KB size 262144KB
*** nvram check start for DG2200TN ***
pmc_init:PMC using DQM mode
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-25) : DG2200TN
Number of MAC Addresses (1-32) : 11
Base MAC Address : 98:77:e7:ee:05:07
PSI Size (1-128) KBytes : 48
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
MC memory allocation (MB) : 4
TM memory allocation (MB) : 44
DHD 0 memory allocation (MB) : 14
DHD 1 memory allocation (MB) : 0
DHD 2 memory allocation (MB) : 0
WLan Feature : 0x00
Partition 1 Size (MB) : 112M
Partition 2 Size (MB) : 1M
Partition 3 Size (MB) : 0M
Partition 4 Size (MB) (Data) : 4M
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (address 0x04500000, flash offset 0x04500000) ...
Decompression LZMA Image OK!
Entry at 0x00008000
Starting program at 0x00008000
Booting Linux on physical CPU 0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.4.11-rt19 (jenkins@kubernetes-slave-brewery-6q7x2) (gcc version 4.6.2 (crosstool-NG git+ab5c880 - SoftAtHome 1.0.2) ) #1 SMP PREEMPT Mon Oct 5 14:01:46 UTC 2020
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: BCM963138
Ignoring unrecognised tag 0x41000603
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writealloc
creating a MT_MEMORY_NONCACHED device at physical address of 0x0fe00000 to virtual address at 0xcfe00000 with size of 0x200000 byte for DSL
creating a MT_MEMORY_NONCACHED device at physical address of 0x0d200000 to virtual address at 0xcd200000 with size of 0x2c00000 byte for RDPA tm
creating a MT_MEMORY_NONCACHED device at physical address of 0x0ce00000 to virtual address at 0xcce00000 with size of 0x400000 byte for RDPA mc
creating a MT_MEMORY_NONCACHED device at physical address of 0x0c000000 to virtual address at 0xcc000000 with size of 0xe00000 byte for DHD dhd0
On node 0 totalpages: 114432
free_area_init_node: node 0, pgdat c059c120, node_mem_map c1000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 992 pages used for memmap
Normal zone: 109344 pages, LIFO batch:31
pmc_init:PMC using DQM mode
pmc_init:fdb1 35f035f 4b004b
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x6a450000, Cache size: 524288 B
PERCPU: Embedded 7 pages/cpu @c1405000 s5824 r8192 d14656 u32768
pcpu-alloc: s5824 r8192 d14656 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113408
Kernel command line: console=ttyS0,115200 earlyprintk debug
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
allocated 1048576 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 192MB 255MB = 447MB total
Memory: 446100k/446100k available, 78188k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0528fb0 (5252 kB)
.init : 0xc0529000 - 0xc054e6c0 ( 150 kB)
.data : 0xc0550000 - 0xc059cfc0 ( 308 kB)
.bss : 0xc059cfe4 - 0xc05defe8 ( 265 kB)
Preemptible hierarchical RCU implementation.
Dump stacks of tasks blocking RCU-preempt GP.
NR_IRQS:256
Cortex A9 MPCORE GIC init
DIST at fc01f000, CPU_IF at fc01e100
map_hw_timer_interrupt,132: interrupt_id 96
map_hw_timer_interrupt,132: interrupt_id 97
map_hw_timer_interrupt,132: interrupt_id 98
map_hw_timer_interrupt,132: interrupt_id 99
sched_clock: 32 bits at 1kHz, resolution 1000000ns, wraps every 4294967295ms
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Calibrating delay loop... 1990.65 BogoMIPS (lpj=995328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
CPU: Testing write buffer coherency: ok
Broadcom Logger v0.1 Oct 5 2020 13:58:06
Setting up static identity map for 0x3e88a0 - 0x3e88d4
CPU1: Booted secondary processor
CPU1: Unknown IPI message 0x1
Brought up 2 CPUs
SMP: Total of 2 processors activated (3981.31 BogoMIPS).
NET: Registered protocol family 16
++++ Powering up USB blocks
bcm63xx_pcie: setting resistor calibration value to 0xa
bcm63xx_pcie: applying serdes parameters
PCIE port 0 link-up
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff]
pci 0000:00:00.0: [14e4:6313] type 01 class 0x060400
pci 0000:00:00.0: PME# supported from D0 D3hot
PCI: bus0: Fast back to back transfers disabled
pci 0000:01:00.0: [14e4:a8db] type 00 class 0x028000
pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:00.0: Checking PCIe ASPM for vendor 14e4 device a8db
PCI: bus1: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x900fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x90000000-0x90007fff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [mem 0x90000000-0x900fffff]
PCI: enabling device 0000:00:00.0 (0140 -> 0143)
bcm63xx_pcie: setting resistor calibration value to 0xa
bcm63xx_pcie: applying serdes parameters
PCIE port 1 link-up
PCI host bridge to bus 0001:00
pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff]
pci 0001:00:00.0: [14e4:6313] type 01 class 0x060400
pci 0001:00:00.0: PME# supported from D0 D3hot
PCI: bus0: Fast back to back transfers disabled
pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000
pci 0001:01:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
pci 0001:01:00.0: reg 18: [mem 0x00000000-0x007fffff 64bit]
pci 0001:01:00.0: reg 20: [mem 0x00000000-0x000fffff 64bit pref]
pci 0001:01:00.0: supports D1 D2
pci 0001:00:00.0: Checking PCIe ASPM for vendor 14e4 device 4365
pci 0001:00:00.0: Disabling PCIe ASPM for vendor 14e4 device 4365
PCI: bus1: Fast back to back transfers disabled
pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit]
pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref]
pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit]
pci 0001:00:00.0: PCI bridge to [bus 01-01]
pci 0001:00:00.0: bridge window [mem 0xa0000000-0xa0bfffff]
pci 0001:00:00.0: bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref]
PCI: enabling device 0001:00:00.0 (0140 -> 0143)
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skb_free_task created successfully
gbpm_do_work scheduled
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Oct 5 2020 14:01:43 initialized
Broadcom GBPM v0.1 Oct 5 2020 14:01:43 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource timer_cs
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
MPTCP: Stable release v0.86.7
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 871
io scheduler noop registered (default)
ramoops: attached 0x100000@0x1ff00000 (16x0x10000)
brd: module loaded
loop: module loaded
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=26152300, chipSelect=0
brcmnand_read_id: CS0: dev_id=adda9095
After: NandSelect=00000001, nandConfig=26152300
Block size=00020000, erase shift=17
NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ad da Hynix HY27UF082G2A 256MB on CS0
Found NAND on CS0: ACC=c3840010, cfg=26152300, flashId=adda9095, tim1=65424458, tim2=80000e55
BrcmNAND version = 0x80000700 256MB @00000000
brcmnand_scan: B4 nand_select = 00000001
brcmnand_scan: After nand_select = 00000001
handle_acc_control: default CORR ERR threshold 3 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS0
brcmnand_reset_corr_threshold: default CORR ERR threshold 3 bits for CS0
***** Found UBIFS Marker at 0x0481ff00
***** Found UBIFS Marker at 0x002fff00
Creating 10 MTD partitions on "brcmnand.0":
0x000004820000-0x0000089e0000 : "rootfs"
0x000000300000-0x000004500000 : "rootfs_update"
0x00000fb00000-0x00000ff00000 : "user"
0x000000000000-0x000000020000 : "nvram"
0x000004500000-0x0000089e0000 : "image"
0x000000020000-0x000004500000 : "image_update"
0x000004500000-0x000004820000 : "bootfs"
0x000000020000-0x000000300000 : "bootfs_update"
0x00000fa00000-0x00000fb00000 : "misc2"
0x000008a00000-0x00000fa00000 : "misc1"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. sequence number: 2
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 65 MiB
UBI: number of good PEBs: 526
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 526
UBI: number of PEBs reserved for bad PEB handling: 5
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 287
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform ehci-platform.0: Generic Platform EHCI Controller
ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform.0: irq 105, io mem 0x8000c300
ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform ohci-platform.0: Generic Platform OHCI Controller
ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform.0: irq 104, io mem 0x8000c400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd.0: irq 106, io mem 0x8000d000
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 0 ports detected
xhci-hcd xhci-hcd.0: xHCI Host Controller
xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 4
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
brcmboard: brcm_board_init entry
DYING GASP IRQ Initialized and Enabled
gpiochip_add: registered GPIOs 0 to 159 on device: bcm_gpio
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe8600 (irq = 64) is a BCM63XX
ttyS1 at MMIO 0xfffe8620 (irq = 65) is a BCM63XX
BPM: tot_mem_size=536870912B (512MB), buf_mem_size <7%> =37580963B (35MB), num of buffers=14498, buf size=2592
Broadcom BPM Module Char Driver v0.1 Oct 5 2020 13:58:17 Registered<244>
u32 classifier
input device check on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (6970 buckets, 27880 max)
ctnetlink v0.93: registering with nfnetlink.
/proc/net/netfilter/nf_dyndscp_w2ldscp_transtbl created
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
L2TP core: blog_l2tp_rcv_check
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Could not find GPIO info for WiFi On/Off button in boardparms!
SoftAtHome Button driver has been initialized
UBIFS: mounted UBI device 0, volume 0, name "rootfs_ubifs"
UBIFS: mounted read-only
UBIFS: file system size: 64249856 bytes (62744 KiB, 61 MiB, 506 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) readonly on device 0:11.
Freeing init memory: 148K
hub 1-0:1.0: over-current condition on port 2
init started: BusyBox v1.13.3 (2020-10-05 13:58:25 UTC)
starting pid 359, tty '': '/etc/init.d/sysinit'
SYSINIT
SoftAtHome HGW version: SHFRSW1.4.12#0
Compiled on kubernetes-slave-brewery-6q7x2, Mon, 05 Oct 2020 14:09:56 +0000
With toolchain gcc version: arm-unknown-linux-gnueabi-gcc (crosstool-NG git+ab5c880 - SoftAtHome 1.0.2) 4.6.2
Mounting tmpfs filesystem (/tmp) ...
Mounting proc filesystem ...
Mounting sys filesystem ...
Mounting tmpfs filesystem (/dev) ...
Mounting tmpfs filesystem (/var) ...
Mounting tmpfs filesystem (/var/log) ...
Mounting usbfs filesystem (/proc/bus/usb) ...
Mounting pstore filesystem (/mnt/pstore) ...
Mounting cgroup filesystem (/sys/fs/cgroup/)
> NORMAL BOOT <
hub 2-0:1.0: over-current condition
UBI: attaching mtd9 to ubi1
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
hub 4-0:1.0: over-current condition on port 2
UBI: max. sequence number: 180
UBI: attached mtd9 to ubi1
UBI: MTD device name: "misc1"
UBI: MTD device size: 112 MiB
UBI: number of good PEBs: 896
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 3
UBI: available PEBs: 683
UBI: total number of reserved PEBs: 213
UBI: number of PEBs reserved for bad PEB handling: 8
UBI: max/mean erase counter: 3/0
UBI: image sequence number: 29569270
UBI: background thread "ubi_bgt1d" started, PID 646
UBI device number 1, total 896 LEBs (113770496 bytes, 108.5 MiB), available 683 LEBs (86724608 bytes, 82.7 MiB), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 1, volume 0, name "user"
UBIFS: file system size: 3174400 bytes (3100 KiB, 3 MiB, 25 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 149934 bytes (146 KiB)
> BOOT SYSTEM <
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 1, volume 1, name "ext"
UBIFS: file system size: 15745024 bytes (15376 KiB, 15 MiB, 124 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 743676 bytes (726 KiB)
## CV=CONFIG_VERSION_NAME_MAJOR="1.4.12" DB=CONFIG_VERSION_NAME_MAJOR="1.4.12"
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 1, volume 2, name "perm"
UBIFS: file system size: 3174400 bytes (3100 KiB, 3 MiB, 25 LEBs)
UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 149934 bytes (146 KiB)
sysinit: start rc.sysinit
Mon Oct 5 13:54:32 CEST 2020
Mounting other filesystems ...
Switching to RUNLEVEL 1 ...
removing abort trigger
*********************** Starting script /etc/rc1.d/S00faultmonitor at: 5.40 4.49
*********************** Starting script /etc/rc1.d/S00syslog-ng at: 5.44 4.52
*********************** Starting script /etc/rc1.d/S00syslog-ng-rotate at: 6.07 5.13
*********************** Starting script /etc/rc1.d/S01EnableRebootOnCrash at: 6.10 5.14
panic_on_page_allocation_failure flag is not present in this kernel release...
*********************** Starting script /etc/rc1.d/S01EnableRebootOnOOM at: 6.14 5.17
*********************** Starting script /etc/rc1.d/S01sysbus at: 6.17 5.20
*********************** Starting script /etc/rc1.d/S01sysctl at: 6.35 5.36
*********************** Starting script /etc/rc1.d/S02hardware at: 6.38 5.39
Wifi Forwarding Driver is initialized!
Initializing WLCSM Module
WLCSM Module loaded successfully
DHD_FKB_POOL size is:1280 and entry size:2592
fkbpool address range: da800000 <-> dab2a000
DHD_PKTTAG POOL size is:1280 and entry size:64
dhd_module_init in
dhd_queue_budget = 256
dhd_sta_threshold = 2048
dhd_if_threshold = 65536
no wifi platform data, skip
dhdpcie_chipmatch: Unsupported vendor 14e4 device a8db
dhdpcie_pci_probe: chipmatch failed!!
PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location)
dhdpcie_init: can't find adapter info for this chip
PCI: enabling device 0001:01:00.0 (0140 -> 0142)
DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000
dhd:0: fw path:/etc/wlan/dhd nv path:(null)
Creating CPU ring for queue number 7 with 128 packets descriptor=0xbf11906c
Done initializing Ring 7 Base=0xffdf3000 End=0xffdf3800 calculated entries= 128 RDD Base=0x00c17000 descriptor=0xbf11906c
RDPA returned tx wakeup reg = <0x80299004>, val = <0x10000000>
RDPA returned rx wakeup reg = <0x8029a004>, val = <0x26000000>
Scratch pad is not initialized.
dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
dhd_attach: wl0: pre-allocated buffer mode is disabled (allocskbsz=0)
dhd_attach(): thread:dhd_watchdog_thread:492 started
dhd_attach(): thread:dhd0_dpc:494 started
dhd_deferred_work_init: work queue initialized
Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf28d82c
Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf28d848
wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3
Instantiating WFD 0 thread
dhd:0: fw path:/etc/wlan/dhd nv path:(null)
dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path=
dhdpcie_ramsize_adj: Enter
dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000
dhdpcie_download_code_file: download firmware /etc/wlan/dhd/4366c0/rtecdc.bin
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/1/1/0/
wl: loading /etc/wlan/bcm43664_DG2200TN_map.bin
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=20
wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=20
Replace or append with internal Mac Address
dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
PCIe shared addr (0x002a5c2c) read took 52023 usec before dongle is ready
DMA RX offset from shared Area 0
dhdpcie_readshared: Dongle advertizes 2 size indices
dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it
H2D DMA WR INDX : array size 544 = 2 * 266
D2H DMA RD INDX : array size 32 = 2 * 3
D2H DMA WR INDX : array size 32 = 2 * 3
H2D DMA RD INDX : array size 544 = 2 * 266
ring_info_raw: 56
24 6b 43 00 f4 7b 43 00 08 7e 43 00 1c 80 43 00
22 80 43 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 0a 01 00 00
dhdpcie_readshared: max H2D queues 266
dhd_bus_start: Initializing 266 h2drings
dhd_runner_flowmgr_init: bootmem name<dhd0> addr<cc000000> size<14680064>
Scratch pad is not initialized.
Scratch pad is not initialized.
Scratch pad is not initialized.
Scratch pad is not initialized.
dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512
Scratch pad is not initialized.
dhd_runner_policy_init: N+M Policy = 0 1 (HW)
dhd_bus_cmn_writeshared:
0000: 00 c0 b3 1c 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 c2 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 40 f0 1a 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 c0 c1 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 c2 00 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 00 40 1a 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 10 14 00
dhd_bus_cmn_writeshared:
0000: 00 88 ed 1a 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 8c ed 1a 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 80 ed 1a 00 00 00 00
dhd_bus_cmn_writeshared:
0000: 00 84 ed 1a 00 00 00 00
Attach flowrings pool for 264 rings
Runner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0>
Initial configuration
=================================
rx_post_flow_ring_base_addr : c0c20000
tx_post_flow_ring_base_addr : cbfc4000
rx_complete_flow_ring_base_addr : c0c28000
tx_complete_flow_ring_base_addr : c0c1c000
r2d_wr_arr_base_addr : ffdd4000
d2r_rd_arr_base_addr : ffdd4402
r2d_rd_arr_base_addr : ffdd4c00
d2r_wr_arr_base_addr : ffdd4802
tx_post_mgmt_arr_base_addr : ffdd5000
tx_post_mgmt_arr_base_phys_addr : 1aed9000
r2d_wr_arr_base_phys_addr : 1aed8000
d2r_rd_arr_base_phys_addr : 1aed8402
r2d_rd_arr_base_phys_addr : 1aed8c00
d2r_wr_arr_base_phys_addr : 1aed8802
Doorbell ISR : bf2b334c
Doorbell CTX : dcd00e00
Runner DHD Offload initialization complete
dhd_rx_frame: net device is NOT registered. drop event packet
dhd_rx_frame: net device is NOT registered. drop event packet
CUR_ETHERADDR : 6
98 77 e7 ee 05 08
dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90
Dongle Host Driver, version 7.14.164.23.cpe4.16L05.0-kdb
wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0
Broadcom PCI Device 0x6313 has allocated with driver pcieport
Broadcom PCI Device 0x6313 has allocated with driver pcieport
dhd_module_init out
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: norm_wmark_tot=9423, pktc_wmark_tot=9423
PCI: enabling device 0000:01:00.0 (0140 -> 0142)
wl: passivemode=1
wl1: creating kthread wl1-kthrd
wl: napimode=0
initvars_cis_pci: Not CIS format
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=pci/0/1/0/
wl: loading /etc/wlan/bcm43217_DG2200TN_map.bin
srom rev:8
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=20
wl1: allocskbmode=1 currallocskbsz=2300
Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf28d864
Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf28d880
wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type skb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc
Instantiating WFD 1 thread
wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1
wl1: Broadcom BCM43227 802.11 Wireless Controller 7.14.164.23.cpe4.16L05.0-kdb
dgasp: kerSysRegisterDyingGaspHandler: wl1 registered
Success
ret code = 0.
ret code = 0.
ret code = 0.
ret code = 0.
ret code = 0.
Note: Loading 6300 MDK (default) driver for 0 chip
Switch MDK: num_switches = 1
Switch MDK: unit = 1; phy_pbmp = 0xf; config_pbmp = 0xf nophy_pbmp = 0x0
Switch MDK link poll thread: unit=1; phypbmp=0xf config_pbmp=0xf
*********************** Starting script /etc/rc1.d/S03mountpackages at: 9.59 8.12
Mount using the default checks
*********************** Starting script /etc/rc1.d/S05hgwcfg_init at: 9.65 8.13
*********************** Starting script /etc/rc1.d/S06switch at: 9.69 8.17
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
Success
*********************** Starting script /etc/rc1.d/S07ebttcpmss at: 9.79 8.26
*********************** Starting script /etc/rc1.d/S07iptables-smod at: 9.84 8.31
*********************** Starting script /etc/rc1.d/S08ebtables at: 9.93 8.39
*********************** Starting script /etc/rc1.d/S10netmodeconfig1 at: 10.04 8.50
*********************** Starting script /etc/rc1.d/S10usermngt at: 10.29 8.80
*********************** Starting script /etc/rc1.d/S17faultmonitorplugin at: 10.43 8.92
*********************** Starting script /etc/rc1.d/S17led_plugin at: 10.48 8.96
*********************** Starting script /etc/rc1.d/S19dhcpv6client at: 10.54 9.01
*********************** Starting script /etc/rc1.d/S20nemo-core at: 10.61 9.07
*********************** Starting script /etc/rc1.d/S20nemo_wlan at: 11.04 9.44
*********************** Starting script /etc/rc1.d/S20network at: 11.10 9.49
*********************** Starting script /etc/rc1.d/S21dsl at: 11.14 9.52
*********************** Starting script /etc/rc1.d/S21generate_key at: 11.29 9.63
Verifying device certificate
WARNING: can't open config file: /openssl/openssl.cnf
/perm/certs/cpe_device.crt.pem: OK
Private device key for CPE WAN_ADDR 98:77:E7:EE:05:07 already exist. No private key generation
A device certificate already exists for CPE WAN_ADDR 98:77:E7:EE:05:07
*********************** Starting script /etc/rc1.d/S21netdev at: 11.55 9.71
*********************** Starting script /etc/rc1.d/S21netmaster at: 11.93 9.96
Line 0: xDSL link down
*********************** Starting script /etc/rc1.d/S21www-backend at: 12.48 10.33
*********************** Starting script /etc/rc1.d/S22firewall at: 12.56 10.40
*********************** Starting script /etc/rc1.d/S22netmodeconfig3 at: 13.01 10.79
*********************** Starting script /etc/rc1.d/S22nmc_led at: 13.30 10.93
*********************** Starting script /etc/rc1.d/S23bcmeth at: 13.49 10.99
*********************** Starting script /etc/rc1.d/S23nemo-clients at: 13.53 11.01
*********************** Starting script /etc/rc1.d/S23raplugin at: 13.59 11.04
*********************** Starting script /etc/rc1.d/S24netmodeconfigqos at: 13.85 11.09
*********************** Starting script /etc/rc1.d/S25dnsplugin at: 14.06 11.11
*********************** Starting script /etc/rc1.d/S25kmcd at: 14.18 11.12
*********************** Starting script /etc/rc1.d/S25pppd at: 14.82 11.51
*********************** Starting script /etc/rc1.d/S28dhcpv6server at: 14.95 11.58
*********************** Starting script /etc/rc1.d/S40conntrack_plugin at: 15.03 11.63
*********************** Starting script /etc/rc1.d/S42fuse at: 15.15 11.70
*********************** Starting script /etc/rc1.d/S43dropbearkey at: 15.21 11.73
*********************** Starting script /etc/rc1.d/S45dhcp at: 15.24 11.76
*********************** Starting script /etc/rc1.d/S45netmodeconfig4 at: 15.52 11.96
*********************** Starting script /etc/rc1.d/S48lxc at: 15.56 12.00
*********************** Starting script /etc/rc1.d/S50deviceinfo at: 15.59 12.03
hco_upgrade_get_partition_info part_type(PART_TYPE_NORM) bufflen(64)
hco_upgrade_get_partition_info: Version Len(8) Version String(1.4.12.0)
hco_upgrade_get_partition_info success version(1.4.12.0)
hco_upgrade_get_partition_info part_type(PART_TYPE_RESC) bufflen(64)
Error fetching the softco version
hco_upgrade_get_partition_info failed 1
*********************** Starting script /etc/rc1.d/S50devicemngt at: 16.58 12.98
*********************** Starting script /etc/rc1.d/S50mqttmessages at: 16.65 13.03
*********************** Starting script /etc/rc1.d/S50nmc_wlan at: 16.77 13.03
*********************** Starting script /etc/rc1.d/S50wld_bcm at: 16.87 13.08
*********************** Starting script /etc/rc1.d/S70avahi at: 17.23 13.39
*********************** Starting script /etc/rc1.d/S71gmap at: 17.38 13.47
Loading gmap modules ...
gMap started.
*********************** Starting script /etc/rc1.d/S71manifest at: 17.72 13.50
*********************** Starting script /etc/rc1.d/S72netmodeconfig2 at: 18.34 13.51
*********************** Starting script /etc/rc1.d/S73eventmanager at: 18.60 13.51
*********************** Starting script /etc/rc1.d/S73httpd at: 18.71 13.51
*********************** Starting script /etc/rc1.d/S74devdiscd at: 18.86 13.51
*********************** Starting script /etc/rc1.d/S75mqttbroker at: 19.04 13.51
*********************** Starting script /etc/rc1.d/S76pwrledstop at: 19.15 13.51
*********************** Starting script /etc/rc1.d/S78dyndns at: 19.22 13.51
*********************** Starting script /etc/rc1.d/S78time-plugin at: 19.32 13.52
*********************** Starting script /etc/rc1.d/S85scheduler at: 19.58 13.56
*********************** Starting script /etc/rc1.d/S87usbhosts at: 19.82 13.56
*********************** Starting script /etc/rc1.d/S90tod at: 19.95 13.56
*********************** Starting script /etc/rc1.d/S90wakeonlan at: 22.07 14.21
*********************** Starting script /etc/rc1.d/S90wlanscheduler at: 22.16 14.21
*********************** Starting script /etc/rc1.d/S91cups-plugin at: 22.28 14.21
*********************** Starting script /etc/rc1.d/S97dbus at: 22.48 14.21
Starting system message bus
*********************** Starting script /etc/rc1.d/S98cwmp at: 22.61 14.21
*********************** Starting script /etc/rc1.d/S98dnssd at: 22.81 14.21
*********************** Starting script /etc/rc1.d/S98location at: 22.98 14.21
*********************** Starting script /etc/rc1.d/S98pass at: 23.06 14.21
cp: omitting directory '/usr/share/ca-certificates//pass'
*********************** Starting script /etc/rc1.d/S98remoteaccess at: 23.50 14.25
*********************** Starting script /etc/rc1.d/S98speedtest at: 23.63 14.25
*********************** Starting script /etc/rc1.d/S98ssw at: 23.81 14.25
*********************** Starting script /etc/rc1.d/S98storage at: 24.13 14.26
*********************** Starting script /etc/rc1.d/S98upgraded at: 24.58 14.26
*********************** Starting script /etc/rc1.d/S98webuiupgrade_plugin at: 24.83 14.26
*********************** Starting script /etc/rc1.d/S99conmon at: 25.21 14.26
*********************** Starting script /etc/rc1.d/S99dhd_monitor at: 25.38 14.27
dhd_monitor launch
*********************** Starting script /etc/rc1.d/S99ieee1905-registrar at: 25.45 14.27
*********************** Starting script /etc/rc1.d/S99invoc at: 25.71 14.27
*********************** Starting script /etc/rc1.d/S99ippingdiagnostics at: 25.91 14.27
*********************** Starting script /etc/rc1.d/S99nmc_automqtt at: 26.08 14.27
*********************** Starting script /etc/rc1.d/S99oopstracker at: 26.29 14.27
*********************** Starting script /etc/rc1.d/S99pbsync at: 26.41 14.27
*********************** Starting script /etc/rc1.d/S99pkgmgr at: 26.52 14.27
*********************** Starting script /etc/rc1.d/S99probe at: 26.66 14.27
chown: unknown user/group figaro:pcb_users
*********************** Starting script /etc/rc1.d/S99processmonitor at: 26.88 14.27
*********************** Starting script /etc/rc1.d/S99pure-ftpd at: 27.02 14.27
*********************** Starting script /etc/rc1.d/S99sahpairing at: 27.18 14.27
*********************** Starting script /etc/rc1.d/S99saveflush at: 27.50 14.27
*********************** Starting script /etc/rc1.d/S99transfer_client at: 27.66 14.27
*********************** Starting script /etc/rc1.d/S99upnp-igd at: 27.95 14.27
*********************** Starting script /etc/rc1.d/S99upnpdiscd at: 28.06 14.28
*********************** Starting script /etc/rc1.d/S99usbupgrade at: 28.14 14.28
*********************** Starting script /etc/rc1.d/S99watchdog at: 28.32 14.28
Sysinit done.
Please press Enter to activate this console.
|
Images
External
Internal
Board front
Board back
CPU
WLAN
BCM4365E
