LB-LINK BL-W1200

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

LB-LINK BL-W1200 (G1)

FCC approval date: 22 July 2016
Country of manuf.: China
Series: AC1200

Amazon image

ASINs
B07CP1GBZ7 (Flag of India.svg, On Amazon)
B07F9QSJPR (Flag of India.svg, On Amazon)

Type: wireless router

FCC ID: S8J-W1200
PCB ID: BL-R7620AG1

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: MediaTek MT7620A
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Winbond W25Q64JVSIQ)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (EtronTech EM68B16CWQH-25H)

Expansion IFs: USB 2.0
USB ports: 1

WI1 chip1: MediaTek MT7620A
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: none

ETH chip1: MediaTek MT7620A
Switch: MediaTek MT7530WU
LAN speed: 1GbE
LAN ports: 4
WAN speed: 1GbE
WAN ports: 1

abgn+ac

Stock bootloader: U-Boot 4.3.0.0 Ralink

Stock FW OS: Linux 2.6.36

TPFirmware supported: OpenWrt • (List | Dev | DLs)

Default SSID: MYWIFI
Default IP address: 192.168.16.1
the IP 192.168.16.1 is used by 8 additional devices
of which 3 are LB-LINK devices

802dot11 OUI: none specified

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.


1200Mbps Wireless Dual Band 11AC Gigabit Router

Product page

"BL-R7620AG1 V1.0" is silkscreened on the board in the FCC photos.

See also: LB-LINK and B-LINK
Ports
  • WAN: 1x GbE (10/100/1000) port
  • LAN: 4x GbE (10/100/1000) ports
  • USB: 1x USB 2.0 port
Antennas
  • 2x external 5dBi antennas (2.4/5GHz)

Serial

  • R2 - two pads of resistor are rx and tx (57600, 8N1)

Boot log

 • Boot log • >>
U-Boot 1.1.3 (Aug 24 2016 - 10:14:04)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Aug 24 2016  Time:10:14:04
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

 GPIO pin 10 reset to switch
#Reset_MT7530
set LAN/WAN WLLLL

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
default: 3
>>>Chip type is MT7620A, GPIO is 13<<<

You choosed 3
                                                                                                                                                                                    0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6634887 Bytes =  6.3 MB
   Load Address: 80000000
   Entry Point:  8000c310
raspi_read: from:50040 len:653d87
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (wangguilin@localhost.localdomain) (gcc version 3.4.2) #44 Mon Mar 20 13:55:18 CST 2017

 The CPU feqenuce set to 580 MHz

 MIPS CPU sleep mode enabled.
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0001ffca
Readback ErrCtl register=0001ffca
Memory: 53500k/65536k available (5534k kernel code, 12036k reserved, 1085k data, 4528k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a101f
RALINK_GPIOMODE = 18101f
PPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = 75afffc0

*************** MT7620 PCIe RC mode *************
PCIE0 enabled
Port 0 N_FTS = 1b105000
init_rt2880pci done
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 14: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 15: assigned [mem 0x20100000-0x201fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
RT3xxx EHCI/OHCI init.
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.15)
msgmni has been set to 104
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
pci-stub: invalid id string ""
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
SMACCR1 -- : 0x000010a4
SMACCR0 -- : 0xbefd8b68
Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x000010a4
SMACCR0 -- : 0xbefd8b68
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.


=== pAd = c0147000, size = 917856 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.2.0_change_by_limin_20160817-SyncECOS
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Ralink EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.36 ehci_hcd
usb usb1: SerialNumber: rt3xxx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: RT3xxx OHCI Controller
usb usb2: Manufacturer: Linux 2.6.36 ohci_hcd
usb usb2: SerialNumber: rt3xxx-ohci
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MTK MSDC device init.
mtk-sd: MediaTek MT6575 MSDC Driver
u32 classifier
    Performance counters on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (835 buckets, 3340 max)
matchsize=264
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
msdc0 -> ops_get_cd return<1> <- msdc_ops_get_cd() : L<2317> PID<kworker/u:1><0x1c>
Warning: unable to open an initial console.
Freeing unused kernel memory: 4528k freed
msdc0 -> ================ <- msdc_set_mclk() : L<686> PID<kworker/u:1><0x1c>
msdc0 -> !!! Set<400KHz> Source<48000KHz> -> sclk<400KHz> <- msdc_set_mclk() : L<687> PID<kworker/u:1><0x1c>
msdc0 -> ================ <- msdc_set_mclk() : L<688> PID<kworker/u:1><0x1c>
Algorithmics/MIPS FPU Emulator v1.5
msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<52> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<8> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<5> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<55> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> XXX CMD<1> MSDC_INT_CMDTMO <- msdc_irq() : L<2461>
msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker/u:1><0x1c>
Welcome to
     ______         __    __          _   ___
    |  ___ \       |  |  |__| ______ | | /  /
    | |___| | ____ |  |   __ |  __  || |/  /
    |  ___  ||____||  |_ |  || |  | ||    |
    | |___| |      |    ||  || |  | || |\  \
    |______/       |____||__||_|  |_||_| \__\


             =System Architecture Department=

init: can't log to /dev/tty5
starting pid 123, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2017-03-20 13:45:51 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# register rt2860


=== pAd = c0782000, size = 2207280 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000!
device_id =0x7662
====> mt76x2_ePA_per_rate_compensate_init: 5871 is_ePA: 1
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
WiFi Mcast disabled=0
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
NVM is FLASH mode (pAd->flash_offset = 0x48000)
===> rt2880_probe


=== pAd = c099f000, size = 2207280 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Not Equal!
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
WiFi Mcast disabled=0
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
NVM is FLASH mode (pAd->flash_offset = 0x40000)
ra1: at CSR addr 0xb0180000, IRQ 4.
<=== rt2880_probe
RX DESC a263a000  size = 4096
RTMPSetDefaultChannel() : default channel to 1
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= -1
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -3, D2 = 4, CalCode = 16 !!!
RT6352_Temperature_Init : BBPR49 = 0xfffffffd
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff3
Current Temperature from BBP_R49=0xfffffff9
 TX BW Filter Calibration !!!
 RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= f, phase= 2)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= e, phase= 2)
TX IQ Calibration Done!
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
Main bssid = 10:a4:be:fd:8b:68
<==== rt28xx_init, Status=0
0x1300 = 00064380
build time =
20141115060606a
rom patch for E3 IC

platform =
ALPS
hw/sw version =
▒▒
patch version =

FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
RX[0] DESC a2014000 size = 4096
RX[1] DESC a2015000 size = 4096
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
WiFi Mcast disabled=0
1. Phy Mode = 49
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
Country Region from e2p = ffff
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
[PMF]APStartUp:: apidx=0, MFPC=0, MFPR=0, SHA256=0
mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=52, HT-CentCh=54, VHT-CentCh=58
APStartUp(): AP Set CentralFreq at 58(Prim=52, HT-CentCh=54, VHT-CentCh=58, BBP_BW=2)
Main bssid = 10:a4:be:fd:8b:6a
<==== rt28xx_init, Status=0
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
Raeth v3.1 (Tasklet,SkbRecycle)

phy_tx_ring = 0x014e2000, tx_ring = 0xa14e2000

phy_rx_ring0 = 0x014e3000, rx_ring0 = 0xa14e3000
SMACCR1 -- : 0x000010a4
SMACCR0 -- : 0xbefd8b68
ESW: Link Status Changed - Port5 Link UP
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
-------->kill_sig_workq, 1145!!!
nl socket is null !
device eth2 entered promiscuous mode
device ra0 entered promiscuous mode
nl socket is null !
device eth2.1 entered promiscuous mode
device rai0 entered promiscuous mode
nl socket is null !
br0: port 3(rai0) entering learning state
br0: port 3(rai0) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
br0: port 3(rai0) entering forwarding state
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
Jan  1 00:00:39 miniupnpd[1843]: WPS listening on port 8888
ADDRCONF(NETDEV_UP): imq0: link is not ready
ADDRCONF(NETDEV_UP): imq1: link is not ready
ADDRCONF(NETDEV_UP): ra1: link is not ready
ADDRCONF(NETDEV_UP): wds0: link is not ready
ADDRCONF(NETDEV_UP): wds1: link is not ready
ADDRCONF(NETDEV_UP): wds2: link is not ready
ADDRCONF(NETDEV_UP): wds3: link is not ready
ADDRCONF(NETDEV_UP): apcli0: link is not ready
ADDRCONF(NETDEV_UP): wdsi0: link is not ready
ADDRCONF(NETDEV_UP): wdsi1: link is not ready
ADDRCONF(NETDEV_UP): wdsi2: link is not ready
ADDRCONF(NETDEV_UP): wdsi3: link is not ready
ADDRCONF(NETDEV_UP): apclii0: link is not ready

/proc/mtd

 • /proc/mtd • >>
dev:    size   erasesize  name
mtd0: 00800000 00010000 "ALL"
mtd1: 00030000 00010000 "Bootloader"
mtd2: 00010000 00010000 "Config"
mtd3: 00010000 00010000 "Factory"
mtd4: 007b0000 00010000 "Kernel"

mount

 • mount • >>
rootfs on / type rootfs (rw)
proc on /proc type proc (rw,relatime)
none on /var type ramfs (rw,relatime)
none on /dev type ramfs (rw,relatime)
none on /etc type ramfs (rw,relatime)
none on /tmp type ramfs (rw,relatime)
none on /media type ramfs (rw,relatime)
none on /sys type sysfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
mdev on /dev type ramfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)

ps

 • ps • >>
  PID USER       VSZ STAT COMMAND
    1 admin     1996 S    init
    2 admin        0 SW   [kthreadd]
    3 admin        0 SW   [ksoftirqd/0]
    4 admin        0 SW   [kworker/0:0]
    5 admin        0 SW   [kworker/u:0]
    6 admin        0 SW<  [khelper]
    7 admin        0 SW   [sync_supers]
    8 admin        0 SW   [bdi-default]
    9 admin        0 SW<  [kblockd]
   10 admin        0 SW   [khubd]
   11 admin        0 SW<  [kmmcd]
   12 admin        0 SW<  [rpciod]
   13 admin        0 SW   [kworker/0:1]
   14 admin        0 SW   [kswapd0]
   15 admin        0 SW<  [nfsiod]
   16 admin        0 SW<  [crypto]
   23 admin        0 SW   [mtdblock0]
   24 admin        0 SW   [mtdblock1]
   25 admin        0 SW   [mtdblock2]
   26 admin        0 SW   [mtdblock3]
   27 admin        0 SW   [mtdblock4]
   28 admin        0 SW   [kworker/u:1]
  117 admin     1252 S    nvram_daemon
  119 admin     1976 S    goahead
  121 admin     1992 S    telnetd
  123 admin     2000 S    /bin/sh
  504 admin        0 SW   [RtmpCmdQTask]
  505 admin        0 SW   [RtmpWscTask]
  510 admin        0 SW   [RtmpCmdQTask]
  511 admin        0 SW   [RtmpWscTask]
  512 admin        0 SW   [RtmpMlmeTask]
  854 admin     1992 S    udhcpc -i eth2.2 -s /sbin/udhcpc.sh -p /var/run/udhcp
 1175 admin     1996 S    udhcpd /etc/udhcpd.conf
 1847 admin     1008 S    dnsmasq
 1960 admin     2016 S    daemon
 1962 admin     1964 S    cmd_convert
 1964 admin     1964 S    cmd_convert
 1965 admin     1964 S    cmd_convert
 5613 admin     1012 S    miniupnpd -G
 5622 admin     1992 S    klogd
 5631 admin     2000 S    syslogd -C8
 6257 admin     1996 R    ps