Manuf (OEM/ODM): Gemtek WRTA-119AG
FCC approval date: 30 December 2004
Country of manuf.: Taiwan
Power: 5 VDC, 2.5 A
Connector type: barrel
Conn. measurements: 5.5 mm (OD), 2.0 mm (ID)
CPU1: Atheros AR5312A
FLA1: 2 MiB 2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Macronix MX29LV160BBTC-90G)
RAM1: 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (ISSI IS42S32200B-6T)
Expansion IFs: none specified
Serial: yes, internal, 9-pin header, Gemtek type1 pinout, (9600,8,N,1), JP1
WI1 chip1: Atheros AR5312A
WI1 chip2: Atheros AR5112A
WI1 802dot11 protocols: a
WI1 antenna connector: U.FL
WI2 chip1: Atheros AR5312A
WI2 chip2: Atheros AR2112A
WI2 802dot11 protocols: bg
WI2 antenna connector: U.FL
ETH chip1: Atheros AR5312A
ETH chip2: IC+ IP101
LAN speed: 100M
LAN ports: 1
Additional chips
2.4GHz Power Amplifier IC;Microsemi;LX5510;MSC, 5510, 531BU;1;InGaP/GaAs HBT;16-pin MLPQ;3 mm x 3 mm;
4.5 to 6GHz Power Amplifier IC;Microsemi;LX5506;MSC, 5506, 530CL;1;InGaP/GaAs HBT;16-pin MLPQ;
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
Dual-Band Wireless Access Point
• Support page • (Template link outdated)
- OEM: Gemtek WRTA-119AG (WRTA-119AG_V01)
- Default credentials are per the FCC manual.
The default SSIDs for this device are linksys-a and linksys-g.
This device appears to support U-NII-2 channels, however, it may not implement Dynamic Frequency Selection (DFS) due to its age.
Serial
Pinout
Credentials
The (default) credentials are the same as the router's default credentials.
Username: <blank>
Password: admin
Info derived from
| Expand • boot log
|
ar531x rev 0x00005742 firmware startup...
SDRAM TEST SKIPPED
Please check the ethernet cable on port 0
Atheros AR5001AP default version 4.0.0.48
Bootloader version 1.01
0
auto-booting...
Attaching to TFFS... done.
Loading /fl/APIMG1...1073872
Starting at 0x804846e0...
/fl/ - Volume is OK
Reading Configuration File "/fl/apcfg".
Configuration file checksum: 4da56 is good
Please check the ethernet cable on port 0!
Attaching interface lo0...done
vp0 macaddr = 00:12:17:77:41:30
vp65536 macaddr = 00:12:17:77:41:31
ae0 macaddr = 00:12:17:77:41:32
start easy conf
wireless access point starting...
wlan1 Ready
wireless access point starting...
Auto Channel Scan selected 5280 MHz, channel 56
wlan0 Ready
Ready
|
| Expand • AP shell help
|
WAP55AG wlan0 -> ?
List of Access Point CLI commands:
add remoteWbr -- Add a remote Wireless Bridge
config wlan -- config wlanX
connect bss -- connect to bssX
del acl -- Delete Access Control List
del key -- Delete Encryption key
del remoteWbr -- Delete a remote Wireless Bridge
find bss -- Find BSS
find channel -- Find Available Channel
find all -- Find All BSS
ftp -- Software update via FTP
get acl -- Display Access Control List
get aging -- Display Aging Interval
get antenna -- Display Antenna Diversity
get association -- Display Association Table
get authentication -- Display Authentication Type
get autochannelselect -- Display Auto Channel Select
get beaconinterval -- Display Beacon Interval
get burstSeqThreshold -- Display Max Number of frames in a Burst
get burstTime -- Display Burst Time
get channel -- Display Radio Channel
get cipher -- Display Encryption cipher
get config -- Display Current AP Configuration
get countrycode -- Display Country Code
get domainsuffix -- Display Domain Name Server suffix
get dtim -- Display Data Beacon Rate (DTIM)
get encryption -- Display Encryption Mode
get fragmentthreshold -- Display Fragment Threshold
get frequency -- Display Radio Frequency (MHz)
get gateway -- Display Gateway IP Address
get groupkeyupdate -- Display Group Key Update Interval (in Seconds)
get hardware -- Display Hardware Revisions
get hostipaddr -- Display Host IP Address
get ipaddr -- Display IP Address
get ipmask -- Display IP Subnet Mask
get jsw -- Display Jumpstart Mode
get key -- Display Encryption Key
get keyentrymethod -- Display Encyrption Key Entry Method
get keysource -- Display Source Of Encryption Keys
get login -- Display Login User Name
get minimumrate -- Display Minimum Rate
get nameaddr -- Display IP address of name server
get operationMode -- Display Operation Mode
get pktLogEnable -- Display Packet Logging Mode
get power -- Display Transmit Power Setting
get radiusname -- Display RADIUS server name or IP address
get radiusport -- Display RADIUS port number
get rate -- Display Data Rate
get reg -- Display the register contents at the given offset
get remoteAp -- Display Remote Ap's Mac Address
get remoteWbr -- Display configured Remote Wireless bridges
get rtsthreshold -- Display RTS/CTS Threshold
get sntpserver -- Display SNTP/NTP Server IP Address
get ssid -- Display Service Set ID
get ssidsuppress -- Display SSID Suppress Mode
get station -- Display Station Status
get SuperG -- Display SuperG Feature Status
get systemname -- Display Access Point System Name
get tzone -- Display Time Zone Setting
get upsd -- Display UPSD Mode
get uptime -- Display UpTime
get vlan -- Display VLAN Mode
get wirelessmode -- Display Wireless LAN Mode
get wmm -- Display WMM Mode
get wmmParamBss -- Display WMM parameters used by STA in this BSS
get wmmParam -- Display WMM parameters used by this AP
get wlanstate -- Display wlan state
help -- Display CLI Command List
ping -- Ping
pktLog -- Packet Log
reboot -- Reboot Access Point
run -- Run command file
quit -- Logoff
set acl -- Set Access Control List
set aging -- Set Aging Interval
set antenna -- Set Antenna
set authentication -- Set Authentication Type
set autochannelselect -- Set Auto Channel Selection
set beaconinterval -- Modify Beacon Interval
set burstSeqThreshold -- Set Max Number of frames in a Burst
set burstTime -- Set Burst Time
set channel -- Set Radio Channel
set cipher -- Set Cipher
set countrycode -- Set Country Code
set domainsuffix -- Set Domain Name Server Suffix
set dtim -- Set Data Beacon Rate (DTIM)
set encryption -- Set Encryption Mode
set factorydefault -- Restore to Default Factory Settings
set fragmentthreshold -- Set Fragment Threshold
set frequency -- Set Radio Frequency (MHz)
set gateway -- Set Gateway IP Address
set groupkeyupdate -- Set Group Key Update Interval (in Seconds)
set hostipaddr -- Set Host IP address
set ipaddr -- Set IP Address
set ipmask -- Set IP Subnet Mask
set jsw -- Set Jumpstart Mode
set key -- Set Encryption Key
set keyentrymethod -- Select Encryption Key Entry Method
set keysource -- Select Source Of Encryption Keys
set login -- Modify Login User Name
set minimumrate -- Set Minimum Rate
set nameaddress -- Set Name Server IP address
set operationMode -- Set operation Mode
set password -- Modify Password
set passphrase -- Modify Passphrase
set pktLogEnable -- Enable Packet Logging
set power -- Set Transmit Power
set radiusname -- Set RADIUS name or IP address
set radiusport -- Set RADIUS port number
set radiussecret -- Set RADIUS shared secret
set rate -- Set Data Rate
set reg -- Set Register Value
set remoteAP -- Set Remote AP's Mac Address
set rtsthreshold -- Set RTS/CTS Threshold
set sntpserver -- Set SNTP/NTP Server IP Address
set ssid -- Set Service Set ID
set ssidsuppress -- Set SSID Suppress Mode
set SuperG -- Super G Features
set systemname -- Set Access Point System Name
set tzone -- Set Time Zone Setting
set upsd -- Set UPSD Mode
set vlan -- Set VLAN Mode
set wlanstate -- Set wlan state
set wirelessmode -- Set Wireless LAN Mode
set wmm -- Set WMM Mode
set wmmParamBss -- Set WMM parameters used by STAs in this BSS
set wmmParam -- Set WMM parameters used by this AP
timeofday -- Display Current Time of Day
version -- Software version
nvram -- nvram utility
|
| Expand • AP shell version + get hardware
|
WAP55AG wlan0 -> version
AP software 4.0.0.80
mars@MARSNB:E:/AP_4.0.0.80_THGSrc_Src/ap/os/vxworks/target/proj/ap-ar5312-production
Jan 26 2005, 16:54:11
WAP55AG wlan0 -> get hardware
wlan0 revisions: mac 5.7 phy 4.2 analog 3.6
PCI Vendor ID: 0x168c, Device ID: 0x13
Sub Vendor ID: 0x168c, Sub Device ID: 0x13
chip is AR5312
|
| Expand • nvram show
|
WAP55AG wlan0 -> nvram show
regulatory_domain=FCC
country_domain=US
wan_proto=static
sys_name=WAP55AG
wan_domain=
lan_ipaddr=192.168.1.246
lan_netmask=255.255.255.0
dhcps_mode=enabled
wan_dns=
login_name=
login_password=admin
lan_gateway=192.168.1.1
wl0_ssid=linksys-a
wl0_channel=0
wl0_stat_mode=enabled
wl0_wirelessmode=11a
wl0_ssid_bcast=enabled
wl0_security_mode=disabled
wl0_encrypt_idx=40
wl0_key_idx=1
wl0_key1=
wl0_key2=
wl0_key3=
wl0_key4=
wl0_cipher_type=tkip
wl0_wpa_passphrase=
wl0_wpa_group_key_interval=1500
wl0_auth_type=open
wl0_transmission_rate=auto
wl0_transmission_power=full
wl0_frame_burst=enabled
wl0_beacon_interval=100
wl0_dtim_interval=1
wl0_frag_threshold=2346
wl0_rts_threshold=2346
wl1_ssid=linksys-g
wl1_channel=6
wl1_stat_mode=enabled
wl1_wirelessmode=11g
wl1_wirelessmode_tmp=11g
wl1_ssid_bcast=enabled
wl1_security_mode=disabled
wl1_encrypt_idx=40
wl1_key_idx=1
wl1_key1=
wl1_key2=
wl1_key3=
wl1_key4=
wl1_cipher_type=tkip
wl1_wpa_passphrase=
wl1_wpa_group_key_interval=1500
wl1_auth_type=open
wl1_basic_rate=default
wl1_transmission_rate=auto
wl1_transmission_power=full
wl1_cts_protection_mode=auto
wl1_frame_burst=enabled
wl1_beacon_interval=100
wl1_dtim_interval=1
wl1_frag_threshold=2346
wl1_rts_threshold=2347
radius_server_ipaddr=0.0.0.0
radius_server_ipaddr_1=0
radius_server_ipaddr_2=0
radius_server_ipaddr_3=0
radius_server_ipaddr_4=0
radius_server_port=1812
radius_shared_key=
radius_shared_key_interval=3600
filter_mode=disabled
filter_type=allow
filter_mac_1=00:00:00:00:00:00
filter_mac_2=00:00:00:00:00:00
filter_mac_3=00:00:00:00:00:00
filter_mac_4=00:00:00:00:00:00
filter_mac_5=00:00:00:00:00:00
filter_mac_6=00:00:00:00:00:00
filter_mac_7=00:00:00:00:00:00
filter_mac_8=00:00:00:00:00:00
filter_mac_9=00:00:00:00:00:00
filter_mac_10=00:00:00:00:00:00
filter_mac_11=00:00:00:00:00:00
filter_mac_12=00:00:00:00:00:00
filter_mac_13=00:00:00:00:00:00
filter_mac_14=00:00:00:00:00:00
filter_mac_15=00:00:00:00:00:00
filter_mac_16=00:00:00:00:00:00
filter_mac_17=00:00:00:00:00:00
filter_mac_18=00:00:00:00:00:00
filter_mac_19=00:00:00:00:00:00
filter_mac_20=00:00:00:00:00:00
filter_mac_21=00:00:00:00:00:00
filter_mac_22=00:00:00:00:00:00
filter_mac_23=00:00:00:00:00:00
filter_mac_24=00:00:00:00:00:00
filter_mac_25=00:00:00:00:00:00
filter_mac_26=00:00:00:00:00:00
filter_mac_27=00:00:00:00:00:00
filter_mac_28=00:00:00:00:00:00
filter_mac_29=00:00:00:00:00:00
filter_mac_30=00:00:00:00:00:00
filter_mac_31=00:00:00:00:00:00
filter_mac_32=00:00:00:00:00:00
filter_mac_33=00:00:00:00:00:00
filter_mac_34=00:00:00:00:00:00
filter_mac_35=00:00:00:00:00:00
filter_mac_36=00:00:00:00:00:00
filter_mac_37=00:00:00:00:00:00
filter_mac_38=00:00:00:00:00:00
filter_mac_39=00:00:00:00:00:00
filter_mac_40=00:00:00:00:00:00
log_mode=disabled
log_ipaddr=0.0.0.0
chk_fw_hdr=enabled
fw_extension=fim
modle_id=LinksysWAP55AGv2
basic_realm=Linksys WAP55AG
restore_defaults=0
firmware_version=1.1
my_firmware_version=1.0.22, Jan 26, 2005
customer_firmware_version=1.1, Jan 26, 2005
wl0_macaddr=00:12:17:77:41:30
wl1_macaddr=00:12:17:77:41:31
lan_macaddr=00:12:17:77:41:32
|
| Expand • ls
|
WAP55AG wlan0 -> ls
nvram 2881
apcfg 3981
config.bin 3863
apcfg.bak 3981
defaults 85
apimg1.hdr 52
defaults.bak 85
apimg1 968660
452608 bytes free
|
