Sitecom WLR-6100

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Sitecom WLR-6100 v1

Type: wireless router

Power: 12 VDC, 2 A
Connector type: barrel

CPU1: Ralink RT6856 (700 MHz)
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Macronix MX25L6405D)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (Nanya Model?)

Expansion IFs: USB 2.0
USB ports: 2

WI1 chip1: Ralink RT3593
WI1 802dot11 protocols: an
WI1 MIMO config: 3x3:3
WI1 antenna connector: none
WI2 chip1: Ralink RT3593
WI2 802dot11 protocols: bgn
WI2 MIMO config: 3x3:3
WI2 antenna connector: none

ETH chip1: Ralink RT6856
Switch: Atheros AR8327N
LAN speed: 1G
LAN ports: 4
WAN speed: 1G
WAN ports: 1

abgn

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 785 additional devices
of which 14 are Sitecom devices
Default login user: admin
Default login password: blank
admin:blank credentials used by 345 additional devices
of which 2 are Sitecom devices

802dot11 OUI: none specified

For a list of all currently documented Ralink chipsets with specifications, see Ralink.

Wireless N900 Gigabit Dual-Band Router X6

"Sitecom WLR-6100 v1 - 001" is written on label.

Product page

On SpeedGuide

Default IP address: 192.168.0.1
Default login username: admin
Default login password: (sticker on the bottom of the device)

Serial

 • Original firmware Boot log (serial) 
U-boot Ver:1.0.0.2 2012/11/14 11:07:27

Board: Ralink APSoC DRAM:  64 MB
flash manufacture id: c2, device id 20 17
find flash: MX25L6405D
Flash size 8MB, sector count = 128
============================================ 
ASIC 6855A_MP (Port5<->GigaSW)
Product Name: WLR-6100
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 
rt6855A_gsw_init: HWCFIST=23009e00

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   3: Boot system code via Flash (default).

   
3: System Boot system code via Flash.
## Booting image at b0050000 ...
   Image Name:   Linux Kernel Image
   Created:      2014-03-06   4:13:37 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1847464 Bytes =  1.8 MB
   Load Address: 80020000
   Entry Point:  80023d30
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

init started: BusyBox v1.13.3 (2014-03-06 12:09:20 CST)
starting pid 740, tty '/dev/console': '/sbin/config_init'
mknod: /dev/ttyS0: File exists
mknod: /dev/ttyS1: File exists
Config Init version: 2.10.20.4 date: 2014/03/06
Wed Jan  1 00:00:00 UTC 2014
ln: /lib/./modules: File exists
starting pid 788, tty '/dev/ttyS0': '/sbin/config_term'
************************************************************************
*                                 WLR-6100                             *
************************************************************************

KernelApp/Ramdisk Ver:2.10.20.4                  Date:2014/03/06
password: 
!!! wrong password !!! 
password: 
!!! wrong password !!!
 • Boot log (serial) - Ralink SDK firmware (not original firmware) 
Linux version 2.6.36 (ris8@ris8-Aspire-5720) (gcc version 3.4.2) #6 Sun Oct 5 01:51:00 CEST 2014
ISPRAM0: PA=002c8000,Size=00008000,enabled
Ralink RT63165 SOC prom init
CPU revision is: 00019555 (MIPS 34Kc)
Determined physical RAM map:
 memory: 03fe0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000020 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000020 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16224
Kernel command line:  es=1 root=/dev/ram0  console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00058174
Readback ErrCtl register=00058174
Memory: 58040k/65408k available (2752k kernel code, 7368k reserved, 820k data, 3096k init, 0k highmem)
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
CPU frequency 699.00 MHz
console [ttyS0] enabled
Calibrating delay loop... 465.30 BogoMIPS (lpj=2326528)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
start PCIe register access

*************** RT6855A PCIe RC mode *************
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x2000ffff] (PCI address [0x20000000-0x2000ffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x2010ffff]
pci 0000:02:00.0: BAR 0: set to [mem 0x20100000-0x2010ffff] (PCI address [0x20100000-0x2010ffff]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x20100000-0x201fffff]
pci 0000:00:01.0:   bridge window [mem pref disabled]
** bus= 0, slot=0x0
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 0, slot=0x1
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 1, slot=0x0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 2000ffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 2, slot=0x1
bus=0x2, slot = 0x1
res[0]->start = 20100000
res[0]->end = 2010ffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
fuse init (API version 7.15)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Ralink gpio driver initialized
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
brd: module loaded
flash manufacture id: c2, device id 20 17
MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880fc
SMACCR0 -- : 0x432880fc
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880ce
SMACCR0 -- : 0x432880ce
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x1fbb0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x1fba1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (906 buckets, 3624 max)
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 3096k freed
init started: BusyBox vAlgorithmics/MIPS FPU Emulator v1.5
1.12.1 (2014-10-05 01:23:5devpts: called with bogus options
5 CEST)
starting pid 216, tty '': '/etc_ro/rcS'
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

starting pid 225, tty '/dev/ttyS0': '/bin/sh'


BusyBox v1.12.1 (2014-10-05 01:23:55 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# internet.sh
Password for 'admin' changed
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found

##### disable 1st wireless interface #####
rmmod: ip_nat_pptp: No such file or directory
rmmod: ip_conntrack_pptp: No such file or directory
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
/sbin/internet.sh: line 559: iptables: not found
/sbin/internet.sh: line 560: iptables: not found
/sbin/internet.sh: line 561: iptables: not found
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.

phy_tx_ring = 0x02918000, tx_ring = 0xa2918000

phy_rx_ring0 = 0x02919000, rx_ring0 = 0xa2919000
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880ce
SMACCR0 -- : 0x432880ce
ESW: Link Status Changed - Port5 Link UP
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = C0710000
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
brctl: iface ra0: No such device
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 1(eth2.1) entering learning state
br0: port 1(eth2.1) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
br0: port 1(eth2.1) entering forwarding state
killall: udhcpd: no process killed
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
rm: cannot remove '/etc/radvd.conf': No such file or directory
/sbin/nat.sh: line 47: iptables: not found
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter  1>/dev/null 2>&1
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
sh: iptables: not found
iptables -P OUTPUT ACCEPT
sh: iptables: not found
iptables -P FORWARD ACCEPT
sh: iptables: not found
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
iptables -A malicious_input_filter -i eth2.2 -p tcp --dport 80 -j DROP
sh: iptables: not found
/bin/super_dmz -f
sh: /bin/super_dmz: not found
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
cat /proc/sys/net/netfilter/nf_conntrack_udp_timeout > /var/.udpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_udp_timeout
cat /var/.udpbackup > /proc/sys/net/netfilter/nf_conntrack_udp_timeout; rm -f /var/.udpbackup
cat /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established > /var/.tcpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established
cat /var/.tcpbackup > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established; rm -f /var/.tcpbackup
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
ntp.sh
ddns.sh
sh: ddns.sh: not found
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -9 watchdog 1>/dev/null 2>&1
rmmod ralink_wdt.o
rmmod: ralink_wdt.o: No such file or directory
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
echo 0 > /proc/sys/net/ipv6/conf/all/forwarding
webs: Listening for HTTP requests at address 10.10.10.254

See also

Retrieved from "https://wikidevi.wi-cat.ru/index.php?title=Sitecom_WLR-6100&oldid=339244"