T-Com Speedport W700V
T-Com Speedport W700V
Availability: EoL
Manuf (OEM/ODM): Arcadyan ARV4528KW -A-LF-LT
(Est.) release date: June 2008
Series: G54
Type: wireless router, dsl modem, analog phone gateway
FCC ID: none available
PCB ID: 14145282002J
Power: 12 VDC, 1.2 A
Connector type: barrel
Conn. measurements: 5.5 mm (OD), 2.1 mm (ID), 9 mm (LEN)
CPU1: Infineon PSB 50505 (235 MHz)
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Eon EN29LV320B-70TCP)
RAM1: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (PSC A2V28S40CTP-G6 × 2)
Expansion IFs: none specified
Serial: yes
WI1 chip1: Atheros AR2413A
WI1 802dot11 protocols: bg
WI1 antenna connector: none
ETH chip1: Infineon PSB 50505
Switch: Infineon ADM6996I
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1
bg
Stock FW OS: SuperTask!
Flags: ADSL2+
Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 295 additional devices
of which 6 are T-Com devices
Default login user: blank
Default login password: 0000
blank:0000 credentials used by 2 additional devices
of which 1 are T-Com devices
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Infineon (Lantiq) chipsets with specifications, see Infineon.
ADSL Home Gateway
- T-Home Speedport W 700V • Manual
Supported DSL standards:
- ADSL=G.992.1, ADSL2 = G.992.3, ADSL2+ = G.992.5
This device would appear to be using the SuperTask! RTOS.
Specifications
- • CPU: Infineon Amazon ADSL2+ (MIPS 4KEc Hard IP Core)
- (OpenSSL 0.9.6a Crypto library, SSL/TLS Library and
- CCL/ITRI VoIP Middleware SIP, SIPTX, UAcore)
- • WLAN: Atheros AR2413A Single-Chip MAC/Baseband/Radio
- • VoIP: Infineon VINETIC-2CPE Voice Processor/Analog Termination
- • Switch: Infineon ADM6996 Samurai (5+1 port 10/100)
Models
- T-Com • Speedport models • AVM
- T-Com Speedport W303V Typ A • ToH
- T-Com Speedport W303V Typ B • ToH
- T-Com Speedport W500V (Tecom Targa WR500 VoIP) • ToH • HW
- T-Com Speedport W501V (Arcadyan ARV4525PW • ToH) • ToH • HW
- T-Com Speedport W502V • HW
- T-Com Speedport W503V Typ C (Arcadyan ARV8528PW22) • ToH
- T-Com Speedport W504V • ToH
- T-Com Speedport W700V (Arcadyan ARV4528KW) • ToH • HW
- T-Com Speedport W701V (AVM Telekom) • ToH • HW
- T-Com Speedport W721V • ToH
- T-Com Speedport W722V Typ B • ToH
- T-Com Speedport W723V Typ A (Askey RTV1645VW)
- T-Com Speedport W723V Typ B (Arcadyan VGV8539) • ToH
- T-Com Speedport W724V Typ B • ToH
- T-Com Speedport W724V Typ C • ToH
- T-Com Speedport W900V • HW
- T-Com Speedport W920V • HW
- T-Com Speedport W921V • ToH
OEM
- Arcadyan ARV4528KW-A-LF-LT • SMC SMC7908VoWBRA
- Arcadyan ARV4528KW-B-LF-90A (DT) •
- Arcadyan ARV4518HW-A-B7 • SMC SMC7908VoWBRA2
- Arcadyan ARV4518PW-A-LF-LT • SMC SMC7908A-ISP
- Arcadyan ARV7518PW (IAD3) • Atheros AR9223
- Arcadyan AR4505KW-A-LF-LT • SMC SMC7904WBRA (Realtek RTL8671)
- Arcadyan AR4505NW • SMC SMC7904WBRA2 (TI TNETW1350A)
- Arcadyan AR7505QW1-A-LF-17 • SMC SMC7904WBRA-N (Infineon)
Serial
Boot log
• boot log • >> |
---|
Version 1.0.1 Read EEPROM Jump to Flash ======================================================================= Wireless ADSL Gateway AMAZON Loader V0.93.0 build Nov 10 2006 17:16:22 Broad Net Technology, INC. ======================================================================= EON EN29LV320B bottom boot 16-bit mode found [GPIO FLOW] SetGpio() Begin .. [GPIO FLOW] SetGpio() End. Copying boot params.....DONE Press Space Bar 3 times to enter command mode ... Flash Checking [0] Passed. Unzipping firmware [0(2)] at 0x80002000 ... [ZIP 1] done In c_entry() function ... CPU : Yangtse Version Chip V1.3, CPU Speed 235 MHz, FPI Speed 117 MHz install_exception [INIT] Interrupt ... [GPIO FLOW] SetGpio() Begin .. [GPIO FLOW] SetGpio() End. ##### _ftext = 0x80002000 ##### _fdata = 0x804E56E0 ##### __bss_start = 0x80560E00 ##### end = 0x81907214 ##### Backup Data from 0x804E56E0 to 0x8190F214~0x8198A934 len 505632 ##### Backup Data completed ##### Backup Data verified [INIT] System Log Pool startup ... [INIT] MTinitialize .. [INIT] usrclk mips_counter_frequency:117500000 r4k_offset: 0001cafc(117500) init_US_counter : time1 = 14 , time2 = 32000055, diff 32000041 US_counter = 59 cnt1 32470186 cnt2 32471421, diff 1235 Runtime code version: 3.30.000 System startup... [INIT] Memory COLOR 0, 2012000 bytes .. [INIT] Memory COLOR 1, 1048576 bytes .. [INIT] Memory COLOR 2, 6096928 bytes .. InitCommSys: RESOURCE_BASE = 29, NUMRES = 640 InitCommSys: EVENT_BASE = 131, NUMEVT = 768 InitCommSys: MAILBOX_BASE = 6, NUMMBX = 64 rzMemory start: 0x80C8D7A4, end 0x810718B4, size 4079888 EON EN29LV320B bottom boot 16-bit mode found Set flash memory layout to Boot Parameters found !!! Bootcode version: V0.93.0 Serial number: J630328053 Hardware version: 01B fread_config_b> sizeof(struct III_Config_t) is 301108 EON EN29LV320B bottom boot 16-bit mode found fread_config_b> 27218 bytes read from flash fread_config_b> 312207 bytes decompressed successfully. my CFGVersionMagic = 33343536 my CFGsize = 301120, my CFGDescSize = 41520 my Version = 3.30.000 My CfgHexSize:11079 My CFGDescSize:41520 old CFGVersionMagic on flash = 33343536 CFGsize on flash = 301120, CFGDescSize on flash = 41520 Version on flash = 3.30.000 === Old CfgHexSize = 11079, Old CFGDescSize = 41520 Unzipping from 80A9E548 to 80A94308 ... [ZIP1] done Uncompressed size = 41518 Tail1 : END_III_Config_t Size of Old CFG_DESC is :41518!!! 1.useCfgDesc:1 Unzipping from 80A917A8 to 80A87568 ... [ZIP1] done Uncompressed size = 41518 2.useCfgDesc:1 Tail : END_III_Config_t useCfgDesc:3 Restore Config file from ver: 3.30.000 !!! DS_Tail:[t_ARV4528KW] RELEASE_BUF_AND_RETURN_OK - fread_config_b() #12550, in amazon/config.c - fread_config_b() #12555, in amazon/config.c ====xxx============================== -->425@-230;*(.4/.4/1,.4/3/1) -->425@-230;30(.1/.25/1,.1/3/1) -->600(.9/4.8) -->600(.3/.5,.3/3) -->600(.9/3.9) GPIO15 = 0 check_WAN_switch returns 0 GPIO15 = 0 default route: 0.0.0.0 BufferInit: BUF_HDR_SZ=128 BUF_ALIGN_SZ=4 BUFFER_OFFSET=192 BUF_BUFSZ0=384 BUF_BUFSZ1=2464 NUM_OF_B0=0 NUM_OF_B1=1000 BUF_POOL0_SZ=0 BUF_POOL1_SZ=2592000 sizeof(BUFFER0)=512,sizeof(BUFFER1)=2592 *BUF0=0x81389924 *BUF1=0x81110c14 Altgn *BUF0=0x81389930 *BUF1=0x81110c20 End at BUF0:0x81389930, BUF1:0x81389920 BUF0[0]=0x81389930 BUF1[0]=0x81110c20 buffer0 pointer init OK! buffer1 pointer init OK! [qm_lnk_init] CLOCKHZ=1000 ... [qm_lnk_init] add if 3 into QM link 0 [qm_cbq_enable] no QM attached [qm_cbq_detach] no QM is attached at link 0 f=3492148201/100000, ns_per_byte=1090005888/100000 New cls: id=0, bw=8080 ns/byte, maxd=0 ms, maxb=32, minb=2, avgpktsz=0, maxpktsz=0, offtime=1, parent=0, borrow=0 pri=0, maxidle=1, minidle=0, maxq=96, clsfg=17 f=2002645667/100000, ns_per_byte=1083109375/100000 New cls: id=1, bw=808080 ns/byte, maxd=0 ms, maxb=16, minb=1, avgpktsz=0, maxpktsz=0, offtime=1, parent=81905fcc, borrow=81905fcc pri=5, maxidle=1, minidle=0, maxq=48, clsfg=21 qm_cbq_attach(): cbqp->cbq_res=22 f=90439747/100000, ns_per_byte=1089990048/100000 New cls: id=2, bw=8162 ns/byte, maxd=0 ms, maxb=32, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=81905fcc, borrow=81905fcc pri=5, maxidle=1, minidle=0, maxq=48, clsfg=21 f=3846176767/100000, ns_per_byte=1072693248/100000 New cls: id=3, bw=799999999 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=0, maxidle=0, minidle=0, maxq=96, clsfg=21 f=3846176767/100000, ns_per_byte=1072693248/100000 New cls: id=4, bw=799999999 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=1, maxidle=0, minidle=0, maxq=48, clsfg=23 f=3846176767/100000, ns_per_byte=1072693248/100000 New cls: id=5, bw=799999999 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=2, maxidle=0, minidle=0, maxq=48, clsfg=23 f=3846176767/100000, ns_per_byte=1072693248/100000 New cls: id=6, bw=799999999 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=3, maxidle=0, minidle=0, maxq=48, clsfg=23 f=3846176767/100000, ns_per_byte=1072693248/100000 New cls: id=7, bw=799999999 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=4, maxidle=0, minidle=0, maxq=48, clsfg=23 f=90439747/100000, ns_per_byte=1089990048/100000 New cls: id=8, bw=8162 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=6, maxidle=1, minidle=0, maxq=48, clsfg=20 CLOCKHZ=1000 gConfig.Interface[0].IP_Addr = 127.0.0.1 gConfig.Interface[0].Subnet_Mask = 255.255.255.255 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! Interface 0 ip = 127.0.0.1 gConfig.Interface[1].IP_Addr = 192.168.2.1 gConfig.Interface[1].Subnet_Mask = 255.255.255.0 ether_register_vlan(1): binding not found ether_init(1): no tagged VLAN vlan=0, vid=1, port_mask=0xf switch_init ... Reg 0xA0: 0x1023 0xA1:0x7 0x12:0x3602 MAC Address: 00:12:bf:93:fd:5d time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! Interface 1 ip = 192.168.2.1 gConfig.Interface[2].IP_Addr = 0.0.0.0 gConfig.Interface[2].Subnet_Mask = 0.0.0.0 ether_register_vlan(2): binding not found ether_init(2): no tagged VLAN PCI: Probing PCI hardware on host bus 0. *(AMAZON_RST_REQ)=0 *(AMAZON_RST_REQ+4)=fffc0002 *(AMAZON_PMU_PWDCR)=3fff CLOCK_CONTROL=0x2 FPI_SEGMENT_ENABLE=0x3ff PCI_MODE=0x1000103 1a168c 2900000 2000001 0 0 0 0 0 0 0 5001 44131113 0 44 0 1c0a0100 Autoconfig PCI channel 0x8054B43C Scanning bus 0, I/O 0xb2400000:0xb2600001, Mem 0xb2000000:0xb2400001 201 203 pci_devfn=0x70 vid=0x168c 201 203 00:0e.0 Class 0200: 168c:001a (rev 01) Mem at 0xb2000000 [size=0x10000] 108 Scanning bus 00 Found 00:70 [168c/001a] 000200 00 201 203 201 203 Fixups for bus 00 Bus scan for 00 returning with max=00 1a168c 2900006 2000001 8000 b2000000 0 0 0 0 0 5001 44131113 0 44 0 1c0a014e [HWLAN] ifno=2 irno=7 port=0x00000000 [INFO] wlan: 0.8.4.2 (Atheros/multi-bss) [INFO] ath_hal: 0.9.17.1 (AR5212, RF5111, RF5112, RF2413, DEBUG, REGOPS_FUNC) [INFO] ath_rate_atheros: Version 2.0.1 Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved [INFO] ath_pci: 0.9.4.5 (Atheros/multi-bss) [PCI] devtag=00000070 probe=80069b10 [HWLAN] devtag = 00000070 [HWLAN] Vendor ID 0x168c [HWLAN] Device ID 0x1a [HWLAN] Base Addr 0xb2000000 [HWLAN] SVendor ID 0x1113 [HWLAN] SDevice ID 0x4413 [HWLAN] Revision ID 0x1 [HWLAN] interrupt vector 0x1 ath_pci_probe : ath_pci_probe : dev->name wifi0 call ath_attach 1 : dev 810fb6bc name 810fc368 wifi0 ath_attach: devid 0x1a dev 810fb6bc name wifi0 call ath_attach : dev 810fb6bc name 810fc368 wifi0 ATH_LOCK_INIT called ... ATH_INIT_TQUEUE() : 800776d4 ??? ATH_INIT_TQUEUE() : 8006fc9c ??? ATH_INIT_TQUEUE() : 800729bc ??? ATH_INIT_TQUEUE() : 8006fc64 ??? ATH_INIT_TQUEUE() : 8006fc2c ??? ATH_INIT_SCHED_TASK() ????? ATH_INIT_TQUEUE() : 80073e4c ??? ath_hal_attach : devid 26 ar5212Attach 1 ar5212Attach 2 [HWLAN] domain from EEPROM 8114 RF silent : 1 [HWLAN] Set HWLAN MAC as LAN MAC .. ar5212Attach: mac address read : 00:12:bf:93:fd:5f _ath_hal_attach: should call AH_MOD_INC_USE_COUNT??? Chan 2412: MaxPow = 90 MinPow = 0 Chan 2412: MaxPow = 88 MinPow = 0 Chan 2417: MaxPow = 90 MinPow = 0 Chan 2417: MaxPow = 87 MinPow = 0 Chan 2422: MaxPow = 90 MinPow = 0 Chan 2422: MaxPow = 87 MinPow = 0 Chan 2427: MaxPow = 90 MinPow = 0 Chan 2427: MaxPow = 87 MinPow = 0 Chan 2432: MaxPow = 90 MinPow = 0 Chan 2432: MaxPow = 86 MinPow = 0 Chan 2437: MaxPow = 90 MinPow = 0 Chan 2437: MaxPow = 86 MinPow = 0 Chan 2442: MaxPow = 90 MinPow = 0 Chan 2442: MaxPow = 86 MinPow = 0 Chan 2447: MaxPow = 90 MinPow = 0 Chan 2447: MaxPow = 86 MinPow = 0 Chan 2452: MaxPow = 90 MinPow = 0 Chan 2452: MaxPow = 86 MinPow = 0 Chan 2457: MaxPow = 90 MinPow = 0 Chan 2457: MaxPow = 86 MinPow = 0 Chan 2462: MaxPow = 90 MinPow = 0 Chan 2462: MaxPow = 86 MinPow = 0 Chan 2467: MaxPow = 90 MinPow = 0 Chan 2467: MaxPow = 86 MinPow = 0 Chan 2472: MaxPow = 90 MinPow = 0 Chan 2472: MaxPow = 86 MinPow = 0 ath_descdma_setup: rx DMA: 40 buffers 1 desc/buf ath_descdma_setup: rx DMA map: A0562DC0 (1600) -> 5647808x (1600) ath_descdma_setup: tx DMA: 200 buffers 2 desc/buf ath_descdma_setup: tx DMA map: A0563400 (16000) -> 5649408x (16000) ath_descdma_setup: beacon DMA: 4 buffers 1 desc/buf ath_descdma_setup: beacon DMA map: A0567280 (160) -> 5665408x (160) ath_xr_rate_setup: rate table too small (13 > 15) should assign open and hard_start_xmit in dev structure ?? SuperG is disabled ???????????????????????????? ieee80211_ifattach : should call _MOD_INC_USE RUNTASK id=2 rapi_tmr_task ... should call register_netdev() ??? wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: mac 7.8 phy 4.5 radio 5.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons call ath_attach 2 : dev 810fb6bc name 810fc368 wifi0 [wifi0] : Atheros 5212 : mem=0xb2000000, irq=0 hw_base=0x00000005 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! [HWLAN] hwlan_ioctl() .. Interface 2 ip = 192.168.2.1 [HWLAN] hwlan_ioctl() .. gConfig.Interface[3].IP_Addr = 0.0.0.0 gConfig.Interface[3].Subnet_Mask = 0.0.0.0 ether_register_vlan(3): phy_idx=0 ether_register_vlan(3): record vlan-id 7 in entry 0 ether_init(3): registered to vlan 0, trunk 0 ether_init(3): vlan_tagged=0 ether_init(3): map to physical ifno 3 Init SAR ifno:3 QID:1 VPI/VCI:1/32 CBM_CELL_SIZE(64) * dev->cbm.free_cell_cnt(16384)=1048576 Addr=0x80b8c000 CBM_QD_SIZE(16) * AMAZON_ATM_MAX_QUEUE_NUM(32)=512 Addr=0x80b8bc00 amazon_atm_devs[0] = 0x80b8b890 registering device 0 ATM_UBR vpi 1 vci 32 itf 0 aal 5 tx cl 1 bw 0 mtu 0 rx cl 1 bw 4000 mtu 0 Class=1 QSB_CLK=58750000 MAX_PCR=0 PCR=4000 MIN_PCR=0 SCR=4000 MBS=10 CDV=0 tprs:0 twfq:16383 ts:0 taus:0 MAC Address: 00:12:bf:93:fd:5e Interface 3 ip = 0.0.0.0 gConfig.Interface[11].IP_Addr = 0.0.0.0 gConfig.Interface[11].Subnet_Mask = 0.0.0.0 IFLNK_PPPOE init : (Linkp)ifno = 11 idx = 2 IFLNK_PPPOE init : (Driverp)ifno = 11 idx = 3 Perferred method at Start = 0 Interface 11 ip = 0.0.0.0 gConfig.Interface[18].IP_Addr = 0.0.0.0 gConfig.Interface[18].Subnet_Mask = 0.0.0.0 ether_register_vlan(18): phy_idx=0 ether_register_vlan(18): record vlan-id 8 in entry 1 ether_init(18): registered to vlan 1, trunk 0 ether_init(18): vlan_tagged=1 ether_init(18): phy already initialized Interface 18 ip = 0.0.0.0 gConfig.Interface[20].IP_Addr = 0.0.0.0 gConfig.Interface[20].Subnet_Mask = 0.0.0.0 ether_register_vlan(20): binding not found ether_init(20): no tagged VLAN PCI: Probing PCI hardware on host bus 0. *(AMAZON_RST_REQ)=0 *(AMAZON_RST_REQ+4)=fffc0002 *(AMAZON_PMU_PWDCR)=3fff CLOCK_CONTROL=0x2 FPI_SEGMENT_ENABLE=0x3ff PCI_MODE=0x1000103 1a168c 2900000 2000001 0 0 0 0 0 0 0 5001 44131113 0 44 0 1c0a0100 Autoconfig PCI channel 0x8054B43C Scanning bus 0, I/O 0xb2400000:0xb2600001, Mem 0xb2000000:0xb2400001 201 203 pci_devfn=0x70 vid=0x168c 201 203 00:0e.0 Class 0200: 168c:001a (rev 01) Mem at 0xb2000000 [size=0x10000] 108 PCI: Bus 00 already known 1a168c 2900006 2000001 8000 b2000000 0 0 0 0 0 5001 44131113 0 44 0 1c0a014e [HWLAN] ifno=20 irno=7 port=0x00000000 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! [HWLAN] hwlan_ioctl() .. Interface 20 ip = 192.168.2.1 [HWLAN] hwlan_ioctl() .. gConfig.Interface[21].IP_Addr = 0.0.0.0 gConfig.Interface[21].Subnet_Mask = 0.0.0.0 ether_register_vlan(21): binding not found ether_init(21): no tagged VLAN PCI: Probing PCI hardware on host bus 0. *(AMAZON_RST_REQ)=0 *(AMAZON_RST_REQ+4)=fffc0002 *(AMAZON_PMU_PWDCR)=3fff CLOCK_CONTROL=0x2 FPI_SEGMENT_ENABLE=0x3ff PCI_MODE=0x1000103 1a168c 2900000 2000001 0 0 0 0 0 0 0 5001 44131113 0 44 0 1c0a0100 Autoconfig PCI channel 0x8054B43C Scanning bus 0, I/O 0xb2400000:0xb2600001, Mem 0xb2000000:0xb2400001 201 203 pci_devfn=0x70 vid=0x168c 201 203 00:0e.0 Class 0200: 168c:001a (rev 01) Mem at 0xb2000000 [size=0x10000] 108 PCI: Bus 00 already known 1a168c 2900006 2000001 8000 b2000000 0 0 0 0 0 5001 44131113 0 44 0 1c0a014e [HWLAN] ifno=21 irno=7 port=0x00000000 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! [HWLAN] hwlan_ioctl() .. Interface 21 ip = 192.168.2.1 [HWLAN] hwlan_ioctl() .. gConfig.Interface[22].IP_Addr = 0.0.0.0 gConfig.Interface[22].Subnet_Mask = 0.0.0.0 ether_register_vlan(22): binding not found ether_init(22): no tagged VLAN PCI: Probing PCI hardware on host bus 0. *(AMAZON_RST_REQ)=0 *(AMAZON_RST_REQ+4)=fffc0002 *(AMAZON_PMU_PWDCR)=3fff CLOCK_CONTROL=0x2 FPI_SEGMENT_ENABLE=0x3ff PCI_MODE=0x1000103 1a168c 2900000 2000001 0 0 0 0 0 0 0 5001 44131113 0 44 0 1c0a0100 Autoconfig PCI channel 0x8054B43C Scanning bus 0, I/O 0xb2400000:0xb2600001, Mem 0xb2000000:0xb2400001 201 203 pci_devfn=0x70 vid=0x168c 201 203 00:0e.0 Class 0200: 168c:001a (rev 01) Mem at 0xb2000000 [size=0x10000] 108 PCI: Bus 00 already known 1a168c 2900006 2000001 8000 b2000000 0 0 0 0 0 5001 44131113 0 44 0 1c0a014e [HWLAN] ifno=22 irno=7 port=0x00000000 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! [HWLAN] hwlan_ioctl() .. Interface 22 ip = 192.168.2.1 [HWLAN] hwlan_ioctl() .. gConfig.Interface[23].IP_Addr = 0.0.0.0 gConfig.Interface[23].Subnet_Mask = 0.0.0.0 ether_register_vlan(23): binding not found ether_init(23): no tagged VLAN PCI: Probing PCI hardware on host bus 0. *(AMAZON_RST_REQ)=0 *(AMAZON_RST_REQ+4)=fffc0002 *(AMAZON_PMU_PWDCR)=3fff CLOCK_CONTROL=0x2 FPI_SEGMENT_ENABLE=0x3ff PCI_MODE=0x1000103 1a168c 2900000 2000001 0 0 0 0 0 0 0 5001 44131113 0 44 0 1c0a0100 Autoconfig PCI channel 0x8054B43C Scanning bus 0, I/O 0xb2400000:0xb2600001, Mem 0xb2000000:0xb2400001 201 203 pci_devfn=0x70 vid=0x168c 201 203 00:0e.0 Class 0200: 168c:001a (rev 01) Mem at 0xb2000000 [size=0x10000] 108 PCI: Bus 00 already known 1a168c 2900006 2000001 8000 b2000000 0 0 0 0 0 5001 44131113 0 44 0 1c0a014e [HWLAN] ifno=23 irno=7 port=0x00000000 time = 08/01/2003, 00:00:00 TRAP(linkUp) : send ok! [HWLAN] hwlan_ioctl() .. Interface 23 ip = 192.168.2.1 [HWLAN] hwlan_ioctl() .. ruleCheck()> Group: 0, Error: Useless rule index will be truncated ruleCheck()> Group: 1, Error: Useless rule index will be truncated ruleCheck()> Group: 2, Error: Useless rule index will be truncated CBAC rule format check succeed !! reqCBACBuf()> init match pool, Have: 1000 Memory Address: 0x818a0a58 ~ 0x818a77d4 reqCBACBuf()> init timeGap pool, Have: 10000 Memory Address: 0x818a77d4 ~ 0x818d8528 reqCBACBuf()> init sameHost pool, Have: 2000 Memory Address: 0x818d8528 ~ 0x818e7f48 CBAC rule pool initialized !! [init_if] local_if_mask=0xf00007 [init_if] local_wiredif_mask=0x2 [init_if] local_wirelessif_mask=0xf00004 [init_if] localorVPN_if_mask=0xf00007 1 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 2 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 3 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 11 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 18 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 20 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 21 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 22 set_timer: ti=0 type=1 ina[00000000] gid[00000000] 23 set_timer: ti=0 type=1 ina[00000000] gid[00000000] Init NAT data structure RUNTASK id=3 if_task if0... RUNTASK id=4 if_task if1... RUNTASK id=5 if_task if2... RUNTASK id=6 if_task if3... RUNTASK id=7 if_task if18... RUNTASK id=8 if_task if20... RUNTASK id=9 if_task if21... RUNTASK id=10 if_task if22... RUNTASK id=11 if_task if23... RUNTASK id=12 timer_task... RUNTASK id=13 conn_mgr... RUNTASK id=14 main_8021x... Build Day = Sep 7 2009 RUNTASK id=15 period_task... ========== ADSL Modem initialization OK ! ====== RUNTASK id=16 dhcp_daemon... RUNTASK id=17 dhcp_clt...on interface 18 [absread] flash_init: RAM's limitation is 32M [absread] flash_init: can not find any existing PFS image Try to extract it from flash Primary image: 0, flash area 2 ---[ ZIP1 head start in 0xB3050000 ]--- found signature: 78h 56h 34h 12h ulImgLens=1310401, LENGTH[2]-12=1900532 length checking OK [0] find End at 0xB318FC00 len=1310401 ---[ ZIP1 head start in 0xB3190000 ]--- found signature: 78h 56h 34h 12h ulImgLens=258336, LENGTH[2]-12=1900532 length checking OK [1] find End at 0xB31CF000 len=258336 ---[ ZIP1 head start in 0xB31CF400 ]--- found signature: 78h 56h 34h 12h ulImgLens=93086, LENGTH[2]-12=1900532 length checking OK [2] find End at 0xB31E5C00 len=93086 ---[ ZIP1 head start in 0xB31E6000 ]--- found signature: 78h 56h 34h 12h ulImgLens=150854, LENGTH[2]-12=1900532 length checking OK [3] find End at 0xB320AC00 len=150854 Image[1] at 0x0013FEC1, len = 1310401 Image[2] at 0x0003F120, len = 258336 Image[3] at 0x00016B9E, len = 93086 Image[4] at 0x00024D46, len = 150854 Unzipping from B3190000 to 81E42000 ... [ZIP1] done Uncompressed size = 1826183 lang_idx == 0 and img_cnt = 1 httpd: listen at 192.168.2.1:80 httpd: listen at 127.0.0.1:9000 RUNTASK httpd... RUNTASK id=21 SSLServer ... g_Server_Cert_Array=0x80b8b7fc RUNTASK id=22 SSLClient ... g_Client_Cert_Array=0x80b8b768 RUNTASK id=23 dnsproxy... RUNTASK id=24 dhcpd_mgmt_task... UPnP is disabled TR64 is enabled TR64 Device initialize success! slot=25 [0] Allocate mailbox 6 [0] Allocate mailbox 7 FirstUseDate:2010-06-22T10:46:37 Starting Multitask... RUNTASK id=28 CMV_task... [0] Allocate resource 29, FreeResource = 1 ifx_ssc_init : nbytes 136 ifx_ssc_set_baud: br = 2 call ifx_ssc_init() = 0 call ifx_ssc_open() = 0 SPI_Init! T_WLAN_INT=2 gSetting.CountryCode=0x8114 gSetting.Interface[T_WLAN_INT].Link_Type=1 RUNTASK id=30 apAppInit... RUNTASK id=33 ScanMIH_task... [qm_outbnd_bw_update] ... [qm_cbq_resetclst] n_totalcls=9 aft rst: id=0, bw=8080 ns/byte, maxd=0 ms, maxb=32, minb=2, avgpktsz=0, maxpktsz=0, offtime=1, parent=0, borrow=0 pri=0, maxidle=1, minidle=0, maxq=96, clsfg=17 aft rst: id=1, bw=808080 ns/byte, maxd=0 ms, maxb=16, minb=1, avgpktsz=0, maxpktsz=0, offtime=1, parent=81905fcc, borrow=81905fcc pri=5, maxidle=1, minidle=0, maxq=48, clsfg=21 aft rst: id=2, bw=8162 ns/byte, maxd=0 ms, maxb=32, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=81905fcc, borrow=81905fcc pri=5, maxidle=1, minidle=0, maxq=48, clsfg=21 aft rst: id=3, bw=800000000 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=0, maxidle=0, minidle=0, maxq=96, clsfg=21 aft rst: id=4, bw=800000000 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=1, maxidle=0, minidle=0, maxq=48, clsfg=23 aft rst: id=5, bw=800000000 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=2, maxidle=0, minidle=0, maxq=48, clsfg=23 aft rst: id=6, bw=800000000 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=3, maxidle=0, minidle=0, maxq=48, clsfg=23 aft rst: id=7, bw=800000000 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=4, maxidle=0, minidle=0, maxq=48, clsfg=23 aft rst: id=8, bw=8162 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=0, maxpktsz=0, offtime=1, parent=819049cc, borrow=819049cc pri=6, maxidle=1, minidle=0, maxq=48, clsfg=20 Unzip DSP firmware ... Unzipping from B31E6000 to 817DFE18 ... [ZIP1] [qm_cbq_enable] CBQ enabled at link: 0, DeQTask=34, wakeup event=12 low_pri_mtu: 2475 [qm_outbnd_bw_update] ok done Uncompressed size = 469056 ADSL Firmware: 1.4.2.4.0.2 [Annex B:0x4208 0x0] Code Swap Request, Page[ 3] Code Swap Request, Page[ 4] ifno2dot1x_if[2]=0 ifno2dot1x_if[24]=81 dot1x_wireless_if_mask=0x1000004 [main_8021x] dot1x_build_if_mapping() completed. apAppInit called ???? VOICE_DRV_Init Reset Duslic 2 High begin Reset Duslic end VINETIC module, version : 1.1.17.3 loaded Board_InitPlatform! Board_InitIrq! ADSL> READY [31] Allocate resource 30, FreeResource = 2 [31] Allocate resource 31, FreeResource = 3 [31] Allocate resource 32, FreeResource = 4 [31] Allocate resource 33, FreeResource = 5 [31] Allocate resource 34, FreeResource = 6 [31] Allocate resource 35, FreeResource = 7 Devnum 1, Ch 0 opened VINETIC_Open /dev/vin10: -2139504624 VINETIC_BasicDeviceInit! VINETIC_BasicDeviceInit: ret = 0! state ------> 20 Devnum 1, Ch 1 opened VINETIC_Open /dev/vin11: -2139504540 [31] Allocate resource 36, FreeResource = 8 [31] Allocate resource 37, FreeResource = 9 [31] Allocate resource 38, FreeResource = 10 [31] Allocate resource 39, FreeResource = 11 initVineticTapi: pInit = 0x80a3f450 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 VINETIC_Host_InitChip: nRev= 20832 VINETIC_Host_InitChip: pDev->nChipRev = 96 Dwld_LoadFirmware: P_RAM ret = 0 Dwld_LoadFirmware: D_RAM ret = 0 Dwld_LoadFirmware: ActivateEdsp ret = 0 Host_DownloadCram: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 Host_SetSlic: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 Host_SetSlic: bbd_slic.data = 0x804993fa, bbd_slic.size = 2 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 bbd_get_block: bbd->buf = 0x80499300, bbd->size = 288 initVineticTapi: ret = 0 VINETIC_Ioctl: Phone 1 IFXPHONE_INIT ok! VINETIC_Ioctl: Phone 1 IFXPHONE_SET_LINEFEED ok! Devnum 1, Ch 2 opened VINETIC_Open /dev/vin12: -2139503156 VINETIC_Ioctl: Phone 2 IFXPHONE_INIT ok! VINETIC_Ioctl: Phone 2 IFXPHONE_SET_LINEFEED ok! Devnum 1, Ch 3 opened VINETIC_Open /dev/vin13: -2139501772 VINETIC_Ioctl: Phone 3 IFXPHONE_INIT ok! VINETIC_Ioctl: Phone 3 IFXPHONE_SET_LINEFEED ok! Devnum 1, Ch 4 opened VINETIC_Open /dev/vin14: -2139500388 VINETIC_Ioctl: Phone 4 IFXPHONE_INIT ok! VINETIC_Ioctl: Phone 4 IFXPHONE_SET_LINEFEED ok! RUNTASK id=35 VINETIC_DRV_Task... [36] Allocate mailbox 8 RUNTASK id=36 VINETIC_T38_Task... RUNTASK id=38 FXO_flash_task... RUNTASK id=37 VOICE_API_task... Step 0 Duslic debug: open device! Board_DevOpen Board_DevOpen 4 77 ---------------------duslic_ResetChMember begin DUSLIC_GpioInit begin DUSLIC_GpioInit end ---------------------duslic_ResetChMember end DUSLIC_Init begin DUSLIC_GpioInit begin DUSLIC_GpioInit end Dwld_LoadCram begin 0 ----> Dwld_LoadCram end DUSLIC_GpioInit begin DUSLIC_GpioInit end Dwld_LoadCram begin 1 ----> Dwld_LoadCram end DUSLIC_Init end DUSLIC_Set_Pcm begin DUSLIC_Set_Pcm End init_DTMF_data: time 3095 cpc5621_open: open devNum=0, chNum=0, pDev=00000000, CPC5621_Devices=8054b9f0 Drv_CPC5621_Init: 0, 1 Drv_CPC5621_Init end pDev->devHandle 807A7AA4 cpc5621_open: open devNum=0, chNum=0, pDev=80b7ff70 before pDev->bOpen == TRUE after pDev->bOpen == TRUE CPC_IO_InstanceInit pDev 80B7FF70 begin before DUSLIC_GpioReserve pDev 80B7FF70 pDev->devHandle 807A7AA4 before DUSLIC_GpioConfig 0 :::::::::::::_GpioConfig begin 807A7AA4 Gpio->nIO 0 :::GPIO_MODE_OUTPUT :::GPIO_INT_DUP_605 :::::::::::::_GpioConfig end before DUSLIC_GpioConfig 1 before DUSLIC_GpioConfig 2 :::::::::::::_GpioConfig begin 807A7AA4 Gpio->nIO 1 :::GPIO_MODE_INPUT :::GPIO_MODE_INT :::GPIO_INT_FALLING :::GPIO_INT_DUP_605 :::::::::::::_GpioConfig end before DUSLIC_GpioConfig 3 :::::::::::::_GpioConfig begin 807A7AA4 Gpio->nIO 2 :::GPIO_MODE_INPUT :::GPIO_MODE_INT :::GPIO_INT_RISING :::GPIO_INT_FALLING :::GPIO_INT_DUP_605 :::::::::::::_GpioConfig end before DUSLIC_GpioConfig 4 :::::::::::::_GpioConfig begin 807A7AA4 Gpio->nIO 3 :::GPIO_MODE_INPUT :::GPIO_MODE_INT :::GPIO_INT_FALLING :::GPIO_INT_DUP_605 :::::::::::::_GpioConfig end force_daa_offhook ch 2 onoff 1 time 3111 CID_Detect CH 2 onoff 0 TAPI_LL_Phone_CidRx_Stop------------------->clear FIFO FOR CID DATA FXO_PolState_DTMFCID --> Disable DTMF CID [HWLAN] [2] rapi_tmr_task running [dhcp_clt] enable dhcp client in interface THS[18] force_daa_offhook ch 2 onoff 0 time 3144 CID_Detect CH 2 onoff 1 FXO_PolState_DTMFCID --> Detect Polarity Changed Enable DTMF CID TEL_DRV_Init TEL_DRV_StartDetVOIPHook TEL_DRV_StartDetDTMF TEL_DRV_StartDetCEDTone TEL_DRV_StartDetVOIPHook TEL_DRV_StartDetDTMF TEL_DRV_StartDetCEDTone TEL_DRV_InitTone When * the value is 60000 When * the value is 60000 sys_voip_cfg->cpt.reorder = 425@-230;20(0.24/0.24/1) TEL_DRV_TONE_REORDER duration = 480 TEL_DRV_InitRing TEL_DRV_SetImpedance >>>> STUN Setting <<<< stun Enable : 1 stun Test Enable : 1 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 stun Server : "", IP : 0.0.0.0 stun Port : 3478 RUNTASK id=39 STUNC_InitTask() ... [31] Allocate resource 40, FreeResource = 12 [31] Allocate mailbox 9 VOICE_DRV_SetRxDataHookFunc VOICE_DRV_SetRxDataHookFunc TEL_MGR_Init [31] Allocate resource 41, FreeResource = 13 tel_mgr_mutex=41 [31] Allocate mailbox 10 TEL_DM_Init [31] Allocate resource 42, FreeResource = 14 [31] Allocate resource 43, FreeResource = 15 TEL_DRV_SetPhoneEvtHookFunc TEL_DRV_SetLineEvtHookFunc TEL_MGR_VoiceChannelInit TEL_MGR_SetVoiceChannel 1 TEL_MGR_SetVoiceChannel: ec mode is 16ms TEL_MGR_SetPhoneEC VOICE_DRV_SetEC TEL_MGR_SetPhoneVAD VOICE_DRV_SetVAD TEL_MGR_SetPhoneGain VOICE_DRV_SetGain ------------------------>TAPI_LL_Phone_Volume Ch 0 TxGain 0 RxGain -7 TEL_MGR_SetPhoneJitter VOICE_DRV_SetJitter TEL_MGR_SetVoiceChannel 2 TEL_MGR_SetVoiceChannel: ec mode is 16ms TEL_MGR_SetPhoneEC VOICE_DRV_SetEC TEL_MGR_SetPhoneVAD VOICE_DRV_SetVAD TEL_MGR_SetPhoneGain VOICE_DRV_SetGain ------------------------>TAPI_LL_Phone_Volume Ch 1 TxGain 0 RxGain -7 TEL_MGR_SetPhoneJitter VOICE_DRV_SetJitter Create task ISDN_GetCCBSCFStatus 41 SIP_CALLBACK_EnableDebug SIP_CORE_EnableDebug SIP_CORE_Init [31] Allocate resource 44, FreeResource = 16 [31] Allocate mailbox 11 SIP_CORE_SetSipStatus SIP_CORE_CreateTask >>> SIP_CORE_Task SIP_CORE_Set_Codec_Bandwidth : Bandwidth_Control = 1 SIP_CORE_Set_Codec_Bandwidth : ADSL / VDSL SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_fax_call] = 106 SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g711_call] = 106 SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g726_32_call] = 85 SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g726_24_call] = 64 SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g729_call] = 43 [31] Allocate resource 45, FreeResource = 17 [21] SSLServer> SSLServer() run [21] ssld_conf_init> ssl server info: [21] PrivateKey= [21] MyCertificate= [21] CaCertificate= [21] SSL_method=31 [21] verify_mode=0 [21] cipher_suites=ADH:SHA1:HIGH:EXP [21] tftp_server_ip=140.92.61.131 [21] fn_myCerttificate=ServCert.pem [21] fn_privateKey=PrivKey.pem [21] fn_caCertificate=CaCert.pem [21] ssld_conf_init> ssl server info end: PKCS12_PBE_add> PKCS12_PBE_add> support RC4 PKCS12_PBE_add> support DES PKCS12_PBE_add> support RC2 [21] pCtx=0x80b7da60 in ssld_conf_init [21] ssld_ctx_reset_cert> re-LoadCACertificate( 3rdCA ) ok!! [21] ssld_ctx_reset_cert> re-LoadCACertificate( 2ndCA ) ok!! [21] ssld_ctx_reset_cert> re-LoadCACertificate( 1stCA ) ok!!ssld_ctx_reset_cert> this is pkcs12 type certificate [21] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 154 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 156 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 158 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 160 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 162 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 168 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 170 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 176 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 184 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 158 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 160 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 162 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 165 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 170 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 176 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 184 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 188 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 190 [21] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [21] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [21] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [21] ssld_ctx_reset_cert : re-LoadServerCertAndKey() ok!! [21] ssld_conf_init> ssld_conf_init() ok [21] SSLServer> bind SSL server socket! [21] SSLServer> listen SSL's basic IO socket! [22] SSLClient> SSLClient() run [22] sslc_conf_init> ssl client info: [22] PrivateKey= [22] MyCertificate= [22] CaCertificate= [22] SSL_method=31 [22] verify_mode=1 [22] cipher_suites=ADH:SHA1:HIGH:EXP [22] tftp_server_ip=140.92.61.131 [22] fn_myCerttificate=ServCert.pem [22] fn_privateKey=PrivKey.pem [22] fn_caCertificate=CaCert.pem [22] sslc_conf_init> ssl client info end: [22] sslc_conf_init> pCtx=0x80b66d5c in ssld_conf_init [22] sslc_ctx_reset_cert> re-LoadCACertificate( 3rdCA ) ok!! [22] sslc_ctx_reset_cert> re-LoadCACertificate( 2ndCA ) ok!! [22] sslc_ctx_reset_cert> re-LoadCACertificate( 1stCA ) ok!!sslc_ctx_reset_cert> this is pkcs12 type certificate [22] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 154 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 156 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 158 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 160 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 162 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 168 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 170 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 176 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 184 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 158 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 160 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 162 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 165 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 170 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 176 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 184 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 188 parse_pk12> /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/pkcs12/p12_kiss.c 190 [22] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [22] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [22] CRYPTO_realloc_clean> malloc_ex_func=0x802b3a58, /cygdrive/e/projects/ipone/source/firmware-ipone/secure/ssl/0.9.8e/openssl/crypto/mem.c 480 [22] sslc_ctx_reset_cert : re-LoadServerCertAndKey() ok!! [22] sslc_conf_init> sslc_conf_init() ok [22] SSLClient> want to bind socket for client application! SSDP Initialization completed... ScanMIH_task> DHCP ip give: 192.168.2.100 ~ 199, range: 100 >> Parse Service 'urn:dslforum-org:service:DeviceInfo:1' : TRUE >> Parse Service 'urn:dslforum-org:service:DeviceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:Layer3Forwarding:1' : TRUE >> Parse Service 'urn:dslforum-org:service:LANConfigSecurity:1' : TRUE >> Parse Service 'urn:dslforum-org:service:ManagementServer:1' : TRUE >> Parse Service 'urn:dslforum-org:service:Time:1' : TRUE >> Parse Service 'urn:dslforum-org:service:UserInterface:1' : TRUE >> Parse Service 'urn:dslforum-org:service:X_VoIP:1' : TRUE >> Parse Service 'urn:dslforum-org:service:LANHostConfigManagement:1' : TRUE >> Parse Service 'urn:dslforum-org:service:LANEthernetInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WLANConfiguration:1' : TRUE >> Parse Service 'urn:dslforum-org:service:Hosts:1' : TRUE >> Parse Device 'urn:dslforum-org:device:LANDevice:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANCommonInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANDSLInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANEthernetInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANDSLConnectionManagement:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANDSLLinkConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANEthernetLinkConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANPPPConnection:1' : TRUE >> Parse Device 'urn:dslforum-org:device:WANConnectionDevice:1' : TRUE >> Parse Device 'urn:dslforum-org:device:WANDevice:1' : TRUE >> Parse Device 'urn:dslforum-org:device:InternetGatewayDevice:1' : TRUETR64::TR64_Init> RUNTASK id=31 TR64_ProcessRequest... RUNTSK l2s3 25 RUNTSK l3l2 45 RUNTSK lll2 46 RUNTSK decrTout 47 ISDN: Q_L2S3:3, Q_L3L2:4, Q_LLL2:5 !IFX_FA_Init: IFIN_FA_StatusBitsInfo error TEL_DRV_EOFEvtCB: channelId(0) !TEL_MGR_ProcPhoneFaxStop !TEL_MGR_ProcPhoneFaxStop: no active call !TEL_MGR_ProcMsg: TEL_MGR_ProcPhoneFaxStop apAppInit called 2 ???? Atheros_NetTask running ... ATH_LOCK called ... GetWdsIfno : return 2 , T_WDS_INT 20 dev 8107d0cc sizeof(struct ath_vap) 1728 sc->sc_rc->arc_vap_space 4 ieee80211_vap_setup : name wlan0 should asigned hard_start_xmit and open in dev structure ??? vap->iv_myaddr : 00:12:bf:93:fd:5f ic->ic_myaddr : 00:12:bf:93:fd:5f should call ieee80211_sysctl_vattach() ??? ===ath_vap_create opmode 6=== ===ath_vap_create:1 avp->av_bcbuf 8089bdc8=== ath_vap_create : sc->sc_stagbeacons 1 814f4448 ===ath_vap_create:2 avp->av_bcbuf 8089bdc8=== ieee80211_reset_bss: old bss 00000000 should call register_netdevice ??? ===ath_vap_create:3 avp->av_bcbuf 8089bdc8=== ATH_UNLOCK called ... Basic 11g Rates: (1,2, 5.5, 11) wlan_confree_do> start ... ------------------->change mode to 3 ,Success wlan_confree_do> start ... Set ESSID to WLAN-93FD23, Success wlan_confree_do> start ... Set channel to 9, Success [HWLAN] gSetting.BasicRate=f Basic 11g Rates: (1,2, 5.5, 11) wlan_confree_do> start ... ------------------->change mode to 3 ,Success request_module : wlan_acl ??? ATH_LOCK called ... should call ath_hal_setcapability -> HAL_CAP_TPC??? ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ----> ieee80211_start_running : dev : 8107d0cc flags 00000000 ATH_UNLOCK called ... rapi_tmr_cancel: cookie 814f4d84, Initialized=1 00000000 814f4020 cookie 814f4d84 814f4020 rapi_tmr_cancel: can't find time structure cookie 814f4d84 rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f4020 cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 rapi_tmr_cancel: cookie 814f4d84, Initialized=1 00000000 814f4020 cookie 814f4d84 814f4020 rapi_tmr_cancel: can't find time structure cookie 814f4d84 ath_beacon_alloc : rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f4020 cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 apAppInit : dev->flags 00001001 [HWLAN] Ready Atheros_NetTask return ... [signal_1x_reset] ... rapi_tmr_cancel: cookie 814f4d84, Initialized=1 00000000 814f4d84 814f35bc 814f4020 cookie 814f4d84 814f4d84 cookie 814f4d84 814f35bc cookie 814f4d84 814f4020 rapi_tmr_cancel: can't find time structure cookie 814f4d84 rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f35bc 814f4020 cookie 8089a2f0 814f35bc cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 ieee80211_reset_bss: old bss 80899034<00:12:bf:93:fd:5f> ND 6 ??? ND7 ??? rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f35bc 814f4020 cookie 8089a2f0 814f35bc cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 ATH_LOCK called ... ath_stop_locked : Shutdown the hardware and driver ???? ATH_UNLOCK called ... wlan_confree_do> start ... Set channel to 0, Success ap_deauth_sta called ??? wlan_confree_do> start ... wlan_confree_do> start ... wlan_confree_do> start ... wlan_confree_do> start ... wlan_confree_do> start ... wlan_confree_do> start ... wlan_confree_do> start ... ATH_LOCK called ... should call ath_hal_setcapability -> HAL_CAP_TPC??? ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ----> ieee80211_start_running : dev : 8107d0cc flags 00000000 ATH_UNLOCK called ... rapi_tmr_cancel: cookie 814f4d84, Initialized=1 00000000 814f35bc 814f4020 cookie 814f4d84 814f35bc cookie 814f4d84 814f4020 rapi_tmr_cancel: can't find time structure cookie 814f4d84 rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f35bc 814f4020 cookie 8089a2f0 814f35bc cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 ap_attach : should call _MOD_INC_USE??? dump channel ... wlan0: scan set 1g, 2g, 3g, 4g, 5g, 6g, 7g, 8g, 9g, 10g, 11g, 12g, 13g dwell min 200 max 300 dump channel 2... ath_sysctl_diversity: call ath_hal_setdiversity!!! ath_sysctl_diversity: call ath_hal_setdiversity!!! ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 ar5212SetTransmitPower : AH_PRIVATE(ah)->ah_tpScale 0 rapi_tmr_cancel: cookie 814f4d84, Initialized=1 00000000 814f35bc 814f4020 cookie 814f4d84 814f35bc cookie 814f4d84 814f4020 rapi_tmr_cancel: can't find time structure cookie 814f4d84 ath_beacon_alloc : rapi_tmr_cancel: cookie 8089a2f0, Initialized=1 00000000 814f35bc 814f4020 cookie 8089a2f0 814f35bc cookie 8089a2f0 814f4020 rapi_tmr_cancel: can't find time structure cookie 8089a2f0 /cygdrive/e/projects/ipone/source/firmware-ipone/linklayer/hwlan_11ag/madwifi/net80211/ieee80211_linux.c-268 : call wireless_send_event ??? [reset_802dot1x] wireless module ready [init_wpa] dot1x_ready[0]=3 [dot1x] : func blob_portstatus_set_global <--------------------- [dot1x] : func blob_set_bcast_key <--------------------- wlan_confree_do> start ... ND 6 ??? tkip_attache: should call _MOD_INC_USE??? ND7 ??? [dot1x] : func blob_set_bcast_keyid <--------------------- [dot1x] : func blob_get_mcast_packets <--------------------- [dot1x] : func blob_deauthenticate_all <--------------------- [init_wpa] dot1x_ready[1]=3 [init_wpa] dot1x_ready[2]=3 [init_wpa] dot1x_ready[3]=3 [init_wpa] dot1x_ready[4]=3 [init_wpa] dot1x_ready[5]=3 [reset_802dot1x] 802.1Xv2 ready ifno2dot1x_if[2]=0 ifno2dot1x_if[24]=81 dot1x_wireless_if_mask=0x1000004 [main_8021x] dot1x_build_if_mapping() completed. [reset_802dot1x] wireless module ready [init_wpa] dot1x_ready[0]=3 [dot1x] : func blob_portstatus_set_global <--------------------- [dot1x] : func blob_set_bcast_key <--------------------- wlan_confree_do> start ... ND 6 ??? ND7 ??? [dot1x] : func blob_set_bcast_keyid <--------------------- [dot1x] : func blob_get_mcast_packets <--------------------- [dot1x] : func blob_deauthenticate_all <--------------------- [init_wpa] dot1x_ready[1]=3 [init_wpa] dot1x_ready[2]=3 [init_wpa] dot1x_ready[3]=3 [init_wpa] dot1x_ready[4]=3 [init_wpa] dot1x_ready[5]=3 [reset_802dot1x] 802.1Xv2 ready ADSL Firmware: 1.4.2.4.0.2 [Annex B:0x4208 0x0] Code Swap Request, Page[ 3] Code Swap Request, Page[ 4] ADSL> READY |