TP-LINK Archer C5 v4.x
Jump to navigation
Jump to search
TP-LINK Archer C5 (SL) v4.x
Manuf (OEM/ODM): Proware
FCC approval date: 26 January 2018
Country of manuf.: China
Series: AC1200
Type: wireless router
FCC ID: TE7C5SPV4
PCB ID: 1706123C5-4.0
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7620A
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (GigaDevice GD25Q64CSIG)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (Zentel A3R12E40DBF-8E)
Expansion IFs: USB 2.0
USB ports: 1
Serial: yes, 4-pin header
WI1 chip1: MediaTek MT7620A
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: solderer
WI2 chip1: MediaTek MT7612E
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7620A
Switch: Realtek RTL8367S
LAN speed: 1GbE
LAN ports: 4
WAN speed: 1GbE
WAN ports: 1
abgn+ac
Stock bootloader: U-Boot 1.1.3
Stock FW OS: Linux 3.10.14
TPFirmware supported: Padavan-ng
Default SSID: TP-Link_XXXX (38 addl. devices)
, TP-Link_XXXX_5G (27 addl. devices)
Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 785 additional devices
of which 97 are TP-LINK devices
Default login user: admin
Default login password: admin
admin:admin credentials used by 1324 additional devices
of which 277 are TP-LINK devices
802dot11 OUI: none specified
| CPU1 brand | WI1 chip1 brand | WI2 chip1 brand | |
|---|---|---|---|
| TP-LINK Archer C5 v1.x | Qualcomm Atheros | Qualcomm Atheros | Qualcomm Atheros |
| TP-LINK Archer C5 v2.x | Broadcom | Broadcom | Broadcom |
| TP-LINK Archer C5 v4.x | MediaTek | MediaTek | MediaTek |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
AC1200 Wireless Dual Band Gigabit Router
- Product page (v1.20/v2.0)
"1706123C5-4.0 Rev1.0sp1" is silkscreened on the board in the FCC photos.
Reviews
Serial
3.3V (115200, 8N1) - labeled J2
<J2>
| 1 | 2 | 3 | 4 |
| TX | RX | GND | VCC |
Boot log
- • Boot log
U-Boot 1.1.3 (Jan 23 2018 - 09:14:29)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
Warning: un-recognized chip ID, please update bootloader!
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 23 2018 Time:09:14:29
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
rt_rtl8367_init(1705):Begin
Wait for RTL8367C Ready
.
RTL8367C is ready now!
rt_rtl8367_init(1749):Call Func rt_rtl8367_enableRgmii()
continue to starting system.
[08][08][08] 0
disable switch forward...
3: System Boot system code via Flash.(0xbc020000)
do_bootm:argc=2, addr=0xbc020000
## Booting image at bc020000 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80484090) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
Linux version 3.10.14 (root@e2a0ff7d55dc) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Tue Jan 23 09:22:26 UTC 2018
The CPU feqenuce set to 580 MHz
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
CPU0 revision is: 00019650 (MIPS 24KEc)
Software DMA cache coherency
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x03ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x03ffffff]
Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock2 rootfstype=squashfs
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Writing ErrCtl register=00017389
Readback ErrCtl register=00017389
Memory: 58412k/65536k available (4663k kernel code, 7124k reserved, 1174k data, 304k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
ftrace: allocating 13655 entries in 27 pages
NET: Registered protocol family 16
RALINK_GPIOMODE = 1ab41d
RALINK_GPIOMODE = 18b41d
PPLL_CFG1=0xe68000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = 75afffc0
*************** MT7620 PCIe RC mode *************
PCIE0 enabled
Port 0 N_FTS = 1b105000
init_rt2880pci done
bio: create slab <bio-0> at 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Load Ralink Timer0 Module
Load Ralink Timer1 Module
MTK/Ralink EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.22)
msgmni has been set to 114
io scheduler noop registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
Ralink gpio driver initialized
brd: module loaded
deice id : c8 40 17 c8 40 (4017c840)
Warning: un-recognized chip ID, please update SPI driver!
GD25Q64B(c8 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000220000 : "kernel"
0x000000220000-0x0000007c0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x0000007c0000-0x0000007d0000 : "config"
0x0000007d0000-0x0000007e0000 : "romfile"
0x0000007e0000-0x0000007f0000 : "ispconfig"
0x0000007f0000-0x000000800000 : "radio"
Register flash device:flash0
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
register rt2860
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
NVM is FLASH mode (pAd->flash_offset = 0x7f8000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
rdm_major = 253
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash( 7df100) 0c-ffffff80-63-ffffffa8-56-52
netif_napi_add() called with weight 128 on device eth0
SMACCR1 -- : 0x00000c80
SMACCR0 -- : 0x63a85652
Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, Tx Ring = 512, Rx Ring = 512
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash( 7df100) 0c-ffffff80-63-ffffffa8-56-52
SMACCR1 -- : 0x00000c80
SMACCR0 -- : 0x63a85652
PROC INIT OK!
Mirror/redirect action on
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (912 buckets, 3648 max)
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
Type=Linux
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
8021q: 802.1Q VLAN Support v1.8
registered taskstats version 1
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 304K (805b4000 - 80600000)
starting pid 713, tty '': '/etc/init.d/rcS'
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ehci-platform ehci-platform: EHCI Host Controller
ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform: irq 18, io mem 0x101c0000
ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform ohci-platform: Generic Platform OHCI Controller
ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
tp_domain init ok
PPTP driver version 0.8.5
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
Please press Enter to activate this console. [ ipt_init ] cmd: /var/tmp/dconf/rc.router
[ dm_readFile ] 2193: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
spiflash_ioctl_read, Read from 0x007c0000 length 0x10000, ret 0, retlen 0x10000
spiflash_ioctl_read, Read from 0x007c0000 length 0x94ee, ret 0, retlen 0x94ee
===>Enter routerspiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
mode
spiflash_ioctl_read, Read from 0x007df500 length 0x29, ret 0, retlen 0x29
spiflash_ioctl_read, Read from 0x007df600 length 0x21, ret 0, retlen 0x21
spiflash_ioctl_read, Read from 0x007df700 length 0x10, ret 0, retlen 0x10
spiflash_ioctl_read, Read from 0x007df200 length 0x4, ret 0, retlen 0x4
spiflash_ioctl_read, Read from 0x00020000 length 0x20c, ret 0, retlen 0x20c
[ rsl_initDevInfo ] cmd: echo 0 > /proc/tplink/mspiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
anufacture_flag
[ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
[ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
[ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
[ tr143_main ] 162: 909 start select, maxFd: 7, msgFd.fd: 5, compFd: 7
sendto: No such file or directory
pid 786 send 2001 error
[ oal_startDynDns ] cmd: dyndns /var/tmp/dconf/dyndns.conf
[ oal_startNoipDns ] cmd: noipdns /var/tmp/dconf/noipdns.conf
[ oal_vlan_fetchState ] 351: Failed to read VLAN file.
ioctl: No such device
[ oal_br_addBridge ] cmd: brctl addbr br0
[ oal_br_addBridge ] cmd: brctl setfd br0 0
[ oal_br_addBridge ] cmd: brctl stp br0 off
[ oal_ipt_addLanRules ] cmd: iptables -t filter -A INPUT -i br+ -j ACCEPT
[ oal_intf_setIntf ] cmd: ifconfig br0 192.168.0use br_hw_addr!
.1 netmask 255.255.255.0 up
[ oal_util_setProcLanAddr ] cmd: echo "br0 16820416," > /proc/net/c 0: 0: C:4C: 5:FFFFFF80
onntract_LocalAdRaeth v3.1 (dr
[ oal_intf_eNAPI
nableIntf ] cmd:,SkbRecycle ifconfig eth0 u)
p
phy_tx_ring = 0x02d38000, tx_ring = 0xa2d38000
phy_rx_ring0 = 0x02d3a000, rx_ring0 = 0xa2d3a000
RTL8367C is ready now!
SMACCR1 -- : 0x00000c80
SMACCR0 -- : 0x63a85652
ESW: Link Status Changed - Port5 Link UP
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
ifconfig: ioctl 0x8913 failed: No such device
[ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
ifconfig: ioctl 0x8913 failed: No such device
[ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
ifconfig: ioctl 0x8913 failed: No such device
[ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
ifconfig: ioctl 0x8913 failed: No such device
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_addVlanTagIntf ] cmd: vconfig add eth0 3
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
set if eth0.3 to *not wan dev
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_addVlanTagIntf ] cmd: vconfig add eth0 4
[ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
set if eth0.4 to *not wan dev
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_addVlanTagIntf ] cmd: vconfig add eth0 5
[ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
set if eth0.5 to *not wan dev
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_addVlanTagIntf ] cmd: vconfig add eth0 6
[ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
set if eth0.6 to *not wan dev
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_addVlanTagIntf ] cmd: vconfig add eth0 2
[ oal_intf_enableIntf ] cmd: ifconfig eth0.2 up
set if eth0.2 to wan dev
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.3
brctl: bridge br0: Invalid argument
[ oal_intf_enableIntf ] cmd: ifconfig edevice eth0.3 entered promiscuous mode
th0.3 up
[ oal_device eth0 entered promiscuous mode
br_addIntfIntoBrbr0: port 1(eth0.3) entered forwarding state
idge ] cmd: brctbr0: port 1(eth0.3) entered forwarding state
l addif br0 eth0.3
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.4
brctl: bridge br0: Invalid argument
[ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
device eth0.4 entered promiscuous mode
[ oal_br_addIntfbr0: port 2(eth0.4) entered forwarding state
IntoBridge ] cmdbr0: port 2(eth0.4) entered forwarding state
: brctl addif br0 eth0.4
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnubr0: port 2(eth0.4) entered disabled state
sedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.5
brctl: bridge br0: Invalid argument
[ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
device eth0.5 entered promiscuous mode
[ oal_br_addIntfbr0: port 3(eth0.5) entered forwarding state
IntoBridge ] cmdbr0: port 3(eth0.5) entered forwarding state
: brctl addif br0 eth0.5
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ br0: port 3(eth0.5) entered disabled state
rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.6
brctl: bridge br0: Invalid argument
[ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
device eth0.6 entered promiscuous mode
[ oal_br_addIntfbr0: port 4(eth0.6) entered forwarding state
IntoBridge ] cmdbr0: port 4(eth0.6) entered forwarding state
: brctl addif br0 eth0.6
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3br0: port 4(eth0.6) entered disabled state
: [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_eth_setIGMPSnoopParam ] cmd: sh /etc/igmp/igmp_snoop.sh 1
[ oal_eth_setIGMPSnoopParam ] cmd: echo 1 > /proc/tplink/eth_igmp_snooping
[ oal_wlan_ra_setCountryRegion ] cmd: cp /etc/SingleSKU.dat /var/Wireless/RT2860AP/SingleSKU.dat
[ oal_wlan_ra_setCountryRegion ] cmd: iwpriv ra0 set CountryRegion=1
ra0 no private ioctls.
[ oal_wlan_ra_loadDriver ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig apcli0 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra1 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra2 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra3 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra4 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra0 down
[ oal_wlan_ra_openVap ] cmd: ifconfig ra0 up
start ch = 1, ch->num = 2
28 28 28 28
28 28 28 28 28 28 28 28
28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
start ch = 3, ch->num = 9
28 28 28 28
28 28 28 28 28 28 28 28
28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
start ch = 12, ch->num = 2
28 28 28 28
28 28 28 28 28 28 28 28
28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
start ch = 14, ch->num = 1
28 28 28 28
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
exec!
spiflash_ioctl_read, Read from 0x007f0000 length 0x200, ret 0, retlen 0x200
eeFlashId = 0x7620!
open DNS error: No such file or directory
[ oal_sys_getOldTZInfo ] 462: Open TZ file error!
[ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
[ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
0x1300 = 00064320
[ oal_wlan_ra_openVap ] cmd: killall -q wscd
[ oal_wlan_ra_openVap ] cmd: wscd -i ra0 -m 1 -w /var/tmp/wsc_upnp/ &
[ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wlan_24G
[ oal_wlan_ra_initWlan ] cmd: ifconfig ra0 up
[ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wladevice ra0 entered promiscuous mode
n_24G
[ oal_br_br0: port 5(ra0) entered forwarding state
addIntfIntoBridgbr0: port 5(ra0) entered forwarding state
e ] cmd: brctl addif br0 ra0
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice apcli0 entered promiscuous mode
0 apcli0
wscd: SSDP UDP PORT = 1900
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra2 entered promiscuous mode
0 ra2
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra3 entered promiscuous mode
0 ra3
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra4 entered promiscuous mode
0 ra4
[ wlan_handleL2Desc ] 2401: br0
[ oal_br_addIndevice ra1 entered promiscuous mode
tfIntoBridge ] cmd: brctl addif br0 ra1
[ oal_wlan_ra_initEnd ] cmd: wlNetlinkTool &
spiflash_ioctl_read, Read from 0x007f0000 length 0x2, ret 0, retlen 0x2
[ oal_wlan_ra_initEnd ] cmd: killall -q wscd
WLAN-Start wlNetlinkTool
[ oal_wlan_ra_initEnd ] cmd: wscd -i ra0 -m 1 -w /var/tmp/wsc_upnp/ &
Waiting for Wireless Events from interfaces...
swWlanChkAhbErr: netlink to do
wscd: SSDP UDP PORT = 1900
[ oal_wlan_ra_setCountryRegion ] cmd: cp /etc/SingleSKU_5G.dat /var/Wireless/RT2860AP/SingleSKU_5G.dat
[ oal_wlan_ra_setCountryRegion ] cmd: iwpriv rai0 set CountryRegionABand=1
Interface doesn't accept private ioctl...
set (8BE2): Network is down
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig apclii0 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai1 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai2 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai3 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai4 down
ifconfig: ioctl 0x8913 failed: No such device
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai0 down
[ oal_wlan_ra_openVap ] cmd: ifconfig rai0 up
build time =
20141115060606a
rom patch for E3 IC
platform =
ALPS
hw/sw version =
Š[10]Š[10]
patch version =
[00][00][00][10]
FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
==============eeFlashId: 30306 ====================
RX[0] DESC a3438000 size = 4096
RX[1] DESC a3439000 size = 4096
E2pAccessMode=2
cfg_mode=14
cfg_mode=14
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
pAd->ed_threshold = 90
pAd->ed_chk = 0
pAd->ed_false_cca_threshold = 250
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
APCli_WPAPSK_KEY, key string required 8 ~ 64 characters!!!
I/F(apcli0) Key1Str is Invalid key length!
I/F(apcli0) Key2Str is Invalid key length!
I/F(apcli0) Key3Str is Invalid key length!
I/F(apcli0) Key4Str is Invalid key length!
1. Phy Mode = 49
spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
==============eeFlashId: 30306 ====================
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
MCS Set = ff ff 00 00 01
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x22, ch_pwr_adj = 0xfffffffe(-2), 0x13B4: 0x1b0f043e
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x22, ch_pwr_adj = 0xfffffffe(-2), 0x13B4: 0x1b0f043e
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x22, ch_pwr_adj = 0xfffffffe(-2), 0x13B4: 0x1b0f043e
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x22, ch_pwr_adj = 0xfffffffe(-2), 0x13B4: 0x1b0f043e
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x22, ch_pwr_adj = 0xfffffffe(-2), 0x13B4: 0x1b0f043e
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
ap_ftkd> Initialize FT KDP Module...
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = 0c:80:63:a8:56:54
mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
<==== rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
[ oal_wlan_ra_openVap ] cmd: killall -q wscd_5G
[ oal_wlan_ra_openVap ] cmd: wscd_5G -i rai0 -m 1 -w /var/tmp/wsc_upnp_5G/ &
[ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wlan_5G
[ oal_wlan_ra_WriteWlanCfgFile ] cmd: iwpriv rai0 set ed_chk=1
wscd: SSDP UDP PORT = 1900
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
[ oal_wlan_ra_initWlan ] cmd: ifconfig rai0 up
[ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wladevice rai0 entered promiscuous mode
n_5G
[ oal_br_abr0: port 11(rai0) entered forwarding state
ddIntfIntoBridgebr0: port 11(rai0) entered forwarding state
] cmd: brctl addif br0 rai0
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice apclii0 entered promiscuous mode
0 apclii0
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai2 entered promiscuous mode
0 rai2
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai3 entered promiscuous mode
0 rai3
[ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai4 entered promiscuous mode
0 rai4
[ wlan_handleL2Desc ] 2401: br0
[ oal_br_addIndevice rai1 entered promiscuous mode
tfIntoBridge ] cmd: brctl addif br0 rai1
wlNetlinkTool isspiflash_ioctl_read, Read from 0x007f8000 length 0x2, ret 0, retlen 0x2
already there.
[ oal_wlan_ra_initEnd ] cmd: killall -q wscd_5G
[ oal_wlan_ra_initEnd ] cmd: wscd_5G -i rai0 -m 1 -w /var/tmp/wsc_upnp_5G/ &
wscd: SSDP UDP PORT = 1900
sendto: No such file or directory
pid 786 send 2030 error
[ oal_startUPnP ] cmd: upnpd -L br0 -W eth0.2 -en 1 -nat 0 -port 80 -url "http://www.tp-link.com" -ma "TP-Link" -mn "Archer_C5" -mv "4.0" -desc "AC1200 Wireless Dual Band Gigabit Router " &
sendto: No such file or directory
pid 786 send 2004 error
[ oal_ovpn_createDir ] cmd: mkdir /var/openvpn
[ oal_ovpn_createDir ] cmd: chmod 777 /var/openvpn
[ oal_ovpn_setupTunMod ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/tun.ko
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ oal_pvpn_setupNeededMod ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko
insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko': No such file or directory
[ oal_startDhcps ] cmd: dhcpd /var/tmp/dconf/udhcpd.conf
[ oal_lan6_startDhcp6s ] cmd: dhcp6s -c /var/tmp/dconf/dhcp6s_br0.conf -P /var/run/dhcp6s_br0.pid br0 &
[ oal_lan6_startRadvd ] cmd: radvd -C /var/tmp/dconf/radvd_br0.conf -p /var/run/radvd_br0.pid &
[ oal_snmp_updateCfg ] cmd: iptables -t filter -D ACL -p udp --dport 161 -j ACCEPT
iptables: Bad rule (does a matching rule exist in that chain?).
[ oal_startSnmp ] cmd: snmpd -f /var/tmp/dconf/snmpd.conf
iptables: Bad rule (does a matching rule exist in that chain?).
radvd starting
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.2
brctl: bridge br0: Invalid argument
[ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.2
brctl: bridge br0: Invalid argument
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
sh: can't create /proc/sys/kernel/core_pattern: nonexistent directory
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation
[ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation
set eth status, stack = 2 [1 1 0 0 0 0]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
[ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
[ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
[ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
[ oal_intf_setIfMac ] cmd: ifconfig eth0.2 down
[ oal_intf_setIfMac ] cmd: ifconfig eth0.2 hw ether 0C:80:63:A8:56:53 up
[ oal_intf_enableIntf ] cmd: ifconfig eth0.2 up
[ oal_ipt_setDDoSRules ] cmd: iptables -F FIREWALL_DDOS
[ ddos_clearAll ] cmd: rm -f /var/tmp/dosHost
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_ftp.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_ftp.ko
[ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 500 -j DROP
iptables: Bad rule (does a matching rule exist in that chain?).
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko
insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko': File exists
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko
insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko': File exists
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_pptp.ko
[ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p tcp --dport 1723 -j DROP
iptables: Bad rule (does a matching rule exist in that chain?).
[ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 1701 -j DROP
iptables: Bad rule (does a matching rule exist in that chain?).
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_tftp.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_tftp.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_h323.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_h323.ko
[ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_sip.ko
[ setupModules ] cmd: insmod /lib/modules/kmdirRalink HW NAT Module Enabled
/kernel/net/ipv4/netfilter/nf_nat_sip.ko
[ oal_wan_HWNat_enable ] cmd: insmod /lib/modules/kmdir/kernel/net/nat/hw_nat/hw_nat.ko
[ oal_initIp6FirewallObj ] cmd: ip6tables -F
[ oal_initIp6FirewallObj ] cmd: ip6tables -X
[ oal_initIp6FirewallObj ] cmd: ip6tables -P INPUT DROP
[ oal_initIp6FirewallObj ] cmd: ip6tables -P FORWARD DROP
[ oal_initIp6FirewallObj ] cmd: ip6tables -P OUTPUT ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -N ACLV6
[ oal_initIp6FirewallObj ] cmd: ip6tables -N FIREWALL
[ oal_initIp6FirewallObj ] cmd: ip6tables -N FWRULE
[ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_FIREWALL
[ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_FWRULE
[ oal_initIp6FirewallObj ] cmd: ip6tables -N PARENTCTL
[ oal_initIp6FirewallObj ] cmd: ip6tables -N PCRULE
[ oal_initIp6FirewallObj ] cmd: ip6tables -N PCDROP
[ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_PARENTCTL
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -i lo -p ALL -j ACCEPT -m comment --comment "loop back"
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j ACLV6
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p icmpv6 ! --icmpv6-type echo-request -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp ! -i br+ --sport 547 --dport 546 -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp -i br+ --sport 546 --dport 547 -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp --sport 521 --dport 521 -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j INPUT_PARENTCTL
[ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j INPUT_FIREWALL
[ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -o br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
[ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -j PARENTCTL
[ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -j FIREWALL
[ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -i br+ -j ACCEPT
[ oal_ipt6_setLanHttpPort ] cmd: ip6tables -A INPUT -i br+ -p tcp --dport 80 -j ACCEPT
[ oal_fw6_setFwEnabeld ] cmd: ip6tables -D FIREWALL -j ACCEPT
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ oal_fw6_setFwEnabeld ] cmd: ip6tables -F FIREWALL
[ oal_fw6_setSpiFirewall ] cmd: ip6tables -t filter -D FORWARD ! -i br+ -m conntrack --ctstate NEW -j ACCEPT
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ oal_initFirewallObj ] cmd: ebtables -N FIREWALL
[ oal_fw_setSpiFirewall ] cmd: iptables -t filter -D FORWARD ! -i br+ -m conntrack --ctstate NEW -j ACCEPT
iptables: Bad rule (does a matching rule exist in that chain?).
[ rsl_setStorageServiceObj ] 1394: mountFlag is 3,We start usb server
[ oal_killDlnaMediaSeverProcess ] cmd: killall ushare
killall: ushare: no process killed
uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
Benjamin Zores (C) 2005-2007, for GeeXboX Team.
See http://ushare.geexbox.org/ for updates.
[ oal_ipt_setWanPort ] cmd: iptables -t filter -D INPUT -p tcp --dport 21 -j ACCEPT
iptables: Bad rule (does a matching rule exist in that chain?).
[ oal_ipt_setWanPort ] cmd: iptables -t nat -D PREROUTING -p tcp --dport 21 -j ACCEPT
iptables: Bad rule (does a matching rule exist in that chain?).
[ oal_ipt_setWanPort ] cmd: ip6tables -t filter -D ACLV6 -p tcp --dport 21 -j ACCEPT
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ oal_ipt_setAclRules ] cmd: iptables -t filter -A ACL -i br+ -p icmp -j ACCEPT
[ oal_ipt_setAclRules ] cmd: ip6tables -t filter -A ACLV6 -i br+ -p icmpv6 --icmpv6-type echo-request -j ACCEPT
[ oal_sys_enablePowerLed ] cmd: echo 1 > /proc/tplink/led_sys
[ cos_init ] cmd: echo 3 > /proc/sys/vm/drop_caches
Found 0 files and subdirectories.
Padavan-ng firmware
trunk/configs/boards/TPLINK/TL_C5-V4/board.h /* TP-LINK ARCHER C2 V1 */ #define BOARD_PID "TL_C5-V4" #define BOARD_NAME "TL_C5-V4" #define BOARD_DESC "TP-Link Archer C5 Wireless Router" #define BOARD_VENDOR_NAME "TP-LINK Technologies CO., LTD." #define BOARD_VENDOR_URL "http://www.tp-link.com/en" #define BOARD_MODEL_URL "http://www.tp-link.com/en/download/Archer-C5_V4.html" #define BOARD_BOOT_TIME 25 #define BOARD_FLASH_TIME 120 #define BOARD_GPIO_BTN_RESET 13 #define BOARD_GPIO_BTN_WPS 2 #define BOARD_GPIO_LED_WPS 1 #undef BOARD_GPIO_LED_ALL #undef BOARD_GPIO_LED_WIFI 72 /* hw led */ #define BOARD_GPIO_LED_SW2G 14 #define BOARD_GPIO_LED_SW5G 12 #define BOARD_GPIO_LED_POWER 42 #define BOARD_GPIO_LED_LAN 8 #define BOARD_GPIO_LED_WAN 10 #undef BOARD_GPIO_LED_WAN_INVERTED #undef BOARD_GPIO_LED_WAN_PHY #undef BOARD_GPIO_LED_WAN_PHY_INVERTED #define BOARD_GPIO_LED_USB 7 #undef BOARD_GPIO_LED_ROUTER #undef BOARD_GPIO_PWR_USB_ON #undef BOARD_GPIO_PWR_USB #undef BOARD_GPIO_PWR_USB2 #define BOARD_HAS_5G_11AC 1 #define BOARD_NUM_ANT_5G_TX 2 #define BOARD_NUM_ANT_5G_RX 2 #define BOARD_NUM_ANT_2G_TX 2 #define BOARD_NUM_ANT_2G_RX 2 #define BOARD_NUM_ETH_LEDS 2 #define BOARD_HAS_EPHY_L1000 1 #define BOARD_HAS_EPHY_W1000 1 trunk/configs/boards/TPLINK/TL_C5-V4/board.mk ################################################################## # Board PID # Board Name # PRODUCT # Note ################################################################## # ARCHERC2 # TP-LINK ARCHER C2 # MT7620 # ################################################################## CFLAGS += -DBOARD_ARCHER_C5 -DVENDOR_TPLINK BOARD_NUM_USB_PORTS=1 ### TP-LINK firmware description ### TPLINK_HWID := 0x04DA857C TPLINK_HWREV := 0x0C000600 TPLINK_HWREVADD := 0x04000000 TPLINK_FLASHLAYOUT := 8Mmtk TPLINK_HVERSION=3
Images
Main board top
Main board bottom
