Tenda AC10

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Tenda AC10 v1.1

FCC approval date: 13 December 2017
Country of manuf.: China
Series: AC1200

Amazon image

ASIN
B00ES6ZQ7O (Flag of the United States.svg, On Amazon, On CCC)
multiple revisions of this device, use caution

Type: wireless router

FCC ID: V7TAC10
IC ID: 9034A-AC10
PCB ID: 10033208

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: Realtek RTL8197FS (1 GHz)
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Winbond W25Q64VSIG)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Realtek RTL8197FS)

Expansion IFs: none specified
Serial: yes, 4-pin header

WI1 chip1: Realtek RTL8197FS
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: Realtek RTL8812BRH
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: none

ETH chip1: Realtek RTL8197FS
Switch: Realtek RTL8367RB
LAN speed: 1G
LAN ports: 3
WAN speed: 1G
WAN ports: 1

abgn+ac

Additional chips
2.4GHz Power Amplifier IC;Richwave;RTC6691H;701, 691H, 749;2;
5GHz Power Amplifier IC;Richwave;xxx;;2;

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 785 additional devices
of which 54 are Tenda devices

802dot11 OUI: none specified

 CPU1 brandWI1 chip1 brandWI2 chip1 brand
Tenda AC10RealtekRealtekRealtek
Tenda AC10URealtekRealtekRealtek

For a list of all currently documented Realtek chipsets with specifications, see Realtek.


867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.),
300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = 1200 Mbps class

AC1200 MU-MIMO Dual Band Gigabit Wi-Fi Router

Product page (CN)

"V1.1" and "10033208" is silkscreened on the top of the board in the FCC photos.

According to the User Manual, only the Tenda AC10U model has a USB port.

The Product Similarity Declaration document says,
  • "The model of AC10U's Power is 12Vdc 1.5A, with a USB port and circuit.
  • The model of AC10's Power is 12Vdc 1A, without a USB port and circuit.
The difference of two models just are adapter power, USB port and circuit. The rest are same.
The difference between the two models has no effect on the power of prototype."

Reviews

Specifications from the review:
  • Number of Antennas/Removable: 4/No
  • Ports: 1x WAN / 3x LAN (GbE)
  • Size: 8.6 x 5.5 x 1.9 inches or 220 x 141.5 x 49 mm
  • Weight: 12.3 ounces or 350 grams

Unbrick procedure

  • Connect router to PC via serial (CH340, PL2303, etc.)
If you don't know GND, RX, TX see below image. YOU DON'T NEED VCC!!!
  • Before power up, press RST/WPS button and hold it, then connect the power.
You should hold RST/WPS for about 15 secs since you connected the power,
in order to enter "disaster mode".
  • Connect cable between WAN1 port and your computer network card.
For that connection set IP 192.168.1.100, subnet mask 255.255.255.0
- you don't need to fill out gateway.
(In my case I've used the portable version of Tftpd64 - v4.62)
  • Open Tftpd32/Tftpd64; Server interfaces → select your connection,
the one with IP 192.168.1.100.
  • Select Tftp Client tab; Host: 192.168.1.6, Port: 69, Local file:
*SELECT YOUR FIRMWARE*, Remote file: *LEAVE EMPTY*,
Block Size: Default and press "Put".
 • Serial • >> •.
====Settings for serial access====
* Bits per second/Baud rate = 115200
* Data Bits = 8
* Parity = none
* Stop bits = 1
* Flow control = none

====Bootloader commands====
<RealTek>?
----------------- COMMAND MODE HELP ------------------
HELP (?)                 : Print this help message
DB <Address> <Len>
DW <Address> <Len>
EB <Address> <Value1> <Value2>...
EW <Address> <Value1> <Value2>...
CMP: CMP <dst><src><length>
IPCONFIG:<TargetAddress>
MEMCPY:<dst><src><length>
AUTOBURN: 0/1
LOADADDR: <Load Address>
J: Jump to <TargetAddress>
reboot
FLI: Flash init
FLR: FLR <dst><src><length>
FLW <dst_ROM_offset><src_RAM_addr>
<length_Byte> <SPI cnt#>: Write to SPI
MDIOR:  MDIOR phyid reg
MDIOW:  MDIOW phyid reg data
PHYR: PHYR <PHYID><reg>
PHYW: PHYW <PHYID><reg><data>
PHYPR: PHYPR <PHYID><page><reg>
PHYPW: PHYPW <PHYID><page><reg><data>
COUNTER: Dump Asic Counter
XMOD <addr>  [jump]
TI : timer init
T : test
ETH : startup Ethernet
CPUClk:
CP0
ERASECHIP
ERASESECTOR
SPICLB (<flash ID>) : SPI Flash Calibration
D8 <Address>
E8 <Address> <Value>

See also

Images