Tenda W311R v2
Jump to navigation
Jump to search
Tenda W311R V2.0
FCC approval date: 13 August 2009
Country of manuf.: China
Type: wireless router
FCC ID: V7TW311R
Power: 9 VAC ~ 50/60 Hz, 0.6 A
Connector type: barrel
CPU1: Ralink RT3050 (320 MHz)
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (KH KH29LV320CBTC-70G)
RAM1: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (Hynix HY57V281620FTP-H × 2)
Expansion IFs: none specified
WI1 chip1: Ralink RT3050
WI1 802dot11 protocols: bgn
WI1 MIMO config: 1x1:1
WI1 antenna connector: none
ETH chip1: Ralink RT3050
Switch: Ralink RT3050
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1
bgn
Stock bootloader: U-Boot 1.1.3
Stock FW OS: Linux 2.6.21
Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 785 additional devices
of which 54 are Tenda devices
Default login user: admin
Default login password: admin
admin:admin credentials used by 1327 additional devices
of which 33 are Tenda devices
802dot11 OUI: none specified
| FCC ID | |
|---|---|
| Nexxt Solutions Nebula 150 (ARN01154U1) | X4Y311 V7TW311R |
| CPU1 brand | WI1 chip1 brand | WI1 chip2 brand | |
|---|---|---|---|
| Tenda W311R v2 | Ralink | Ralink | |
| Tenda W311R v3 | Broadcom | Broadcom |
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
150Mbps Wireless N Router
Manuf: SHENZHEN TENDA TECHNOLOGY CO., LTD.
Serial
TENDA W311R RXD and TXD are (LV)TTL signals (0V/3.3V)
Output from Serial:
| • boot log |
|---|
... netboot_common, argc= 3
**********buf = 0x81fcc120
**********NexTxPacket = 81fe4200
NetTxPacket = 0x81FE4200
NetRxPackets[0] = 0x81FE4800
NetRxPackets[1] = 0x81FE4E00
NetRxPackets[2] = 0x81FE5400
NetRxPackets[3] = 0x81FE5A00
NetRxPackets[4] = 0x81FE6000
NetRxPackets[5] = 0x81FE6600
NetRxPackets[6] = 0x81FE6C00
NetRxPackets[7] = 0x81FE7200
NetRxPackets[8] = 0x81FE7800
NetRxPackets[9] = 0x81FE7E00
NetRxPackets[10] = 0x81FE8400
NetRxPackets[11] = 0x81FE8A00
NetRxPackets[12] = 0x81FE9000
NetRxPackets[13] = 0x81FE9600
NetRxPackets[14] = 0x81FE9C00
NetRxPackets[15] = 0x81FEA200
NetRxPackets[16] = 0x81FEA800
NetRxPackets[17] = 0x81FEAE00
NetRxPackets[18] = 0x81FEB400
NetRxPackets[19] = 0x81FEBA00
KSEG1ADDR(NetTxPacket) = 0xA1FE4200
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.0.2; our IP address is 192.168.0.1
Filename 'new_firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (xx:xx:xx:xx:xx:xx)
Got it
T #
first block received
#####################
done
Bytes transferred = 2263332 (228924 hex)
NetBootFileXferSize= 00228924
Erase linux kernel block !!
From 0xBF050000 To 0xBF27FFFF
b_end =BF3FFFFF
Erase Flash from 0xbf050000 to 0xbf27ffff in Bank # 1
erase sector = 12
sect = 12,s_last = 46,erase poll = 1162313
erase sector = 13
*sect = 13,s_last = 46,erase poll = 1129504
erase sector = 14
sect = 14,s_last = 46,erase poll = 1140228
erase sector = 15
*sect = 15,s_last = 46,erase poll = 1157035
erase sector = 16
sect = 16,s_last = 46,erase poll = 1139250
erase sector = 17
*sect = 17,s_last = 46,erase poll = 1129126
erase sector = 18
sect = 18,s_last = 46,erase poll = 1139748
erase sector = 19
*sect = 19,s_last = 46,erase poll = 1129480
erase sector = 20
sect = 20,s_last = 46,erase poll = 1139490
erase sector = 21
*sect = 21,s_last = 46,erase poll = 1143826
erase sector = 22
*sect = 22,s_last = 46,erase poll = 1162855
erase sector = 23
sect = 23,s_last = 46,erase poll = 1128879
erase sector = 24
*sect = 24,s_last = 46,erase poll = 1139675
erase sector = 25
sect = 25,s_last = 46,erase poll = 1129157
erase sector = 26
*sect = 26,s_last = 46,erase poll = 1139747
erase sector = 27
sect = 27,s_last = 46,erase poll = 1129426
erase sector = 28
*sect = 28,s_last = 46,erase poll = 1166804
erase sector = 29
sect = 29,s_last = 46,erase poll = 1129289
erase sector = 30
*sect = 30,s_last = 46,erase poll = 1139221
erase sector = 31
sect = 31,s_last = 46,erase poll = 1129088
erase sector = 32
*sect = 32,s_last = 46,erase poll = 1139862
erase sector = 33
*sect = 33,s_last = 46,erase poll = 1129024
erase sector = 34
sect = 34,s_last = 46,erase poll = 1140403
erase sector = 35
*sect = 35,s_last = 46,erase poll = 1129116
erase sector = 36
sect = 36,s_last = 46,erase poll = 1155807
erase sector = 37
*sect = 37,s_last = 46,erase poll = 1152082
erase sector = 38
sect = 38,s_last = 46,erase poll = 1157580
erase sector = 39
*sect = 39,s_last = 46,erase poll = 1134264
erase sector = 40
sect = 40,s_last = 46,erase poll = 1130220
erase sector = 41
*sect = 41,s_last = 46,erase poll = 1130296
erase sector = 42
sect = 42,s_last = 46,erase poll = 1130919
erase sector = 43
*sect = 43,s_last = 46,erase poll = 1118854
erase sector = 44
*sect = 44,s_last = 46,erase poll = 1130192
erase sector = 45
sect = 45,s_last = 46,erase poll = 1118694
erase sector = 46
*sect = 46,s_last = 46,erase poll = 1185088
done
Erased 35 sectors
Copy linux image[2263332 byte] to Flash[0xBF050000]....
Copy to Flash...
Copy 2263332 byte to Flash...
addr = 0xBF0A33B6 ,cnt=1922414
addr = 0xBF0F6762 ,cnt=1581506
addr = 0xBF149AE6 ,cnt=1240638
addr = 0xBF19CE7E ,cnt=899750
addr = 0xBF1F01F8 ,cnt=558892
addr = 0xBF243588 ,cnt=218012 done
## Booting image at bf050000 ...
Image Name: linkn Kernel Image
Created: 2009-02-09 13:26:01 UTC
System Control Status = 0x20440000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2263268 Bytes = 2.2 MB
Load Address: 80000000
Entry Point: 803cd000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 803cd000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (root@linux-6091) (gcc version 3.4.2)
#452 Mon Feb 9 21:25:31 CST 2009
The CPU feqenuce set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 800068, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 27328k/32768k available (3378k kernel code,
5440k reserved, 510k data, 1116k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=3976704
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>
Load RT2880 Timer Module(Wdg/Soft)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60
256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x00000100
GDMA1_MAC_ADRL -- : 0x000c4330
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
2860 version : 2.0.0.0 (Feb 9 2009)
=== pAd = c0000000, size = 485320 ===
<-- RTMPAllocAdapterBlock, Status=0
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 4 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00400000 : "Kernel"
block2mtd: version $Revision: 1.1.1.1 $
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
arp_tables: (C) 2002 David S. Miller
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 1116k freed
init started: BusyBox v1.12.1 (2009-02-09 21:19Algorithmics/MIPS FPU Emulator v1.5
:29 CST)
starting pid 14, tty '': '/etc_ro/rcS'
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Yes: kernel reg pid 21 success
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
****** WeLoveLinux ******
Welcome to ...
httpd Reg gpio hook success .
starting pid 25, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2009-02-09 21:19:29 RX DESC a04ad000 size = 2048
CST) built-in shell (ash)
Enter<-- RTMPAllocTxRxRingMemory, Status=0
'help' for a list of built-in commands.
# 1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff 00 00 00 01
Main bssid = 00:b0:0c:01:45:78
The UUID Hex string is:2880288028801880a88000b00c014578
The UUID ASCII string is:28802880-2880-1880-a880-00b00c014578!
<==== RTMPInitialize, Status=0
0x1300 = 00064380
getIfLive: device eth2.1 not found.
Commit crc = d253c90f
maclist:
WLan[00:B0:0C:01:45:78]
Lan[00:B0:0C:01:45:78]
Wan[00:B0:0C:GDMA1_MAC_ADRH -- : 0x00000100
01:45:7d]
GDMA1_MAC_ADRL -- : 0x00b00c01
phy_tx_ring = 0x01d81000, tx_ring = 0xa1d81000, size: 16 bytes
phy_rx_ring = 0x01d82000, rx_ring = 0xa1d82000, size: 16 bytes
GDMA1_FWD_CFG = 10000
eth2.1: Setting MAC address to xx xx xx xx xx xx.
VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
eth2.2: Setting MAC address to xx xx xx xx xx xx.
device eth2 entered promiscuous mode
VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
getIfLive: device br0 not found.
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
Router ip address config success.
br0: port 1(eth2.1) entering learning state
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
libupnp: using UDP SSDP_PORT = 1900
br0: topology change detected, propagating
br0: port 1(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
killall: udhcpd: no process killed
ND -> Bad_Sig_entry [18]...
httpd listen ip = 192.168.0.1 port = 80
MfgThread start loop.
TendaLog -> ok rtn.
macBcast uses obsolete (PF_INET,SOCK_PACKET)
IsSameNET [192.168.0.1/255.255.255.0][192.168.1.1/255.255.255.0]
sntp: host not found
killall: dnrd: no process killed
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
route: ioctl 0x890b failed: File exists
libupnp: using UDP SSDP_PORT = 1900
upnpd[289]: UPnP SDK Successfully Initialized.
Mar 29 09:36:22 upnpd[289]: UPnP SDK Successfully Initialized.
upnpd[289]: Succesfully set the Web Server Root Directory.
Mar 29 09:36:22 upnpd[289]: Succesfully set the Web Server Root Directory.
upnpd[289]: IGD root device successfully registered.
Mar 29 09:36:23 upnpd[289]: IGD root device successfully registered.
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
Startnat end.
upnpd[289]: Advertisements Sent. Listening for requests ...
Mar 29 09:36:25 upnpd[289]: Advertisements Sent. Listening for requests ...
............ wan unlink ..4.
............ wan unlink ..5.
|
Images
