Thomson TG585v7

Thomson TG585 v7

FCC approval date: 03 January 2008
Country of manuf.: China

Type: wireless router, dsl modem

FCC ID: RSE-TG585V7
US: TMBDL01BTG585V7

Power: 22 VDC, 0.41 A
Connector type: barrel

CPU1: Broadcom BCM6338 (240 MHz)
FLA1: 4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Spansion S29GL032N90TFI04)
RAM1: 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (Elpida DS1216AGTA-75-E)

Expansion IFs: none specified

WI1 chip1: Broadcom BCM4318
WI1 802dot11 protocols: bg
WI1 antenna connector: U.FL

ETH chip1: Broadcom BCM6338
Switch: Broadcom BCM5325E
LAN speed: 100M
LAN ports: 4

bg

Stock bootloader: CFE 1.0.37 6.5.17

Stock FW OS: Linux 2.6.32.9

Flags: ADSL2+

Default IP address: 192.168.1.254
the IP 192.168.1.254 is used by 158 additional devices
of which 4 are Thomson devices

802dot11 OUI: none specified

	CPU1 brand	WI1 chip1 brand	WI1 chip2 brand
Thomson TG585v7	Broadcom	Broadcom
Thomson TG585v8	Lantiq	Ralink

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

---

Technicolor product page

Wikis

• On the OpenWrt Wiki (FCC ID)

Forum threads

• On the OpenWrt forums

The user mentioned no working ethernet or wifi.

.. however the switch might be supported according to:

openwrt-devel mailing list

Wi-Fi should be supported by b43

"BCM4318 chipset: AP mode does not work because of packet loss

in high transmission rates. Hard to debug & fix." (solved? [from here])

Serial

copied from ali1234's post on the above OpenWrt forums

• OpenWrt boot log

CFE version 1.0.37-6.5.17 for BCM96338 (32bit,SP,BE) Copyright (C) 2000-2005 Broadcom Corporation. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name AM29LV320MB, id 0x2200, size 4096KB error on Ethernet Switch setup Failed initializing enet hardware CPU type 0x29010: 240MHz Total memory: 16777216 bytes (16MB) Total memory used by CFE: 0x80401000 - 0x805283F0 (1209328) Initialized Data: 0x8041D7F0 - 0x8041FA50 (8800) BSS Area: 0x8041FA50 - 0x804263F0 (27040) Local Heap: 0x804263F0 - 0x805263F0 (1048576) Stack Area: 0x805263F0 - 0x805283F0 (8192) Text (code) segment: 0x80401000 - 0x8041D7E8 (116712) Boot area (physical): 0x00529000 - 0x00569000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Board Id Name : 96338W Psi size in KB : 24 Number of MAC Addresses (1-32) : 2 Base MAC Address : 00:11:22:33:44:55 Ethernet PHY Type : External Switch Using Reverse MII Memory size in MB : 16 CMT Thread Number : 0 Dying Gasp Enable (0:Disable 1:Enable) : 0 Could not activate network interface 'eth0': CFE error -1 *** Press Enter to stop auto run (3 seconds) *** Auto run second count down: 0 Code Address: 0x80010000, Entry Address: 0x80010000 Decompression OK! Entry at 0x80010000 Starting program at 0x80010000 Linux version 2.6.32.9 (nico@desktop-de-nico) (gcc version 4.3.3 (GCC) ) #2 Tue Mar 23 07:32:51 CET 2010 Detected Broadcom 0x6338 CPU revision a2 CPU frequency is 240 MHz 16MB of RAM installed registering 8 GPIOs board_bcm963xx: CFE version: 1.0.37-6.5 bootconsole [early0] enabled CPU revision is: 00029010 (Broadcom BCM6338) board_bcm963xx: board name: 96338W Determined physical RAM map: memory: 01000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00001000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00001000 Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs, jffs2 noinitrd console=ttyS0,115200 PID hash table entries: 64 (order: -4, 256 bytes) Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes Memory: 13304k/16384k available (2134k kernel code, 3080k reserved, 459k data, 136k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:128 Calibrating delay loop... 238.59 BogoMIPS (lpj=477184) Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 512 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 512 bind 512) TCP reno registered NET: Registered protocol family 1 audit: initializing netlink socket (disabled) type=2000 audit(0.236:1): initialized squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 25 io scheduler noop registered io scheduler deadline registered (default) gpiodev: gpio device registered with major 254 gpiodev: gpio platform device registered with access mask FFFFFFFF bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled bcm963xx_flash: 0x00400000 at 0x1fc00000 bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. bcm963xx_flash: Read Signature value of CFE1CFE1 bcm963xx_flash: CFE bootloader detected bcm963xx_flash: CFE boot tag found with version 6, board type 6338W, and tagid bccfe. bcm963xx_flash: Partition 0 is CFE offset 80c78a20 and length 0 bcm963xx_flash: Partition 1 is kernel offset c7e and length 0 bcm963xx_flash: Partition 2 is rootfs offset cbf and length 0 bcm963xx_flash: Partition 3 is nvram offset d00 and length 0 bcm963xx_flash: Partition 4 is linux offset d40 and length 0 bcm963xx_flash: Spare partition is 2b0000 offset and length 140000 Creating 5 MTD partitions on "bcm963xx": 0x000000000000-0x000000010000 : "CFE" 0x000000010100-0x0000000f0000 : "kernel" mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 0x0000000f0000-0x0000003f0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000 0x0000002b0000-0x0000003f0000 : "rootfs_data" 0x0000003f0000-0x000000400000 : "nvram" 0x000000010000-0x0000003f0000 : "linux" bcm63xx_wdt started, timer margin: 30 sec Registered led device: adsl Registered led device: ses Registered led device: ppp-fail Registered led device: power Registered led device: stop TCP westwood registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 136k freed Please be patient, while OpenWrt loads ... - preinit - Press f<ENTER> to enter failsafe mode - regular preinit - switching to jffs2 mini_fo: using base directory: / mini_fo: using storage directory: /jffs - init - Please press Enter to activate this console. eth0: link forced UP - 100/full - flow control off/off Generic kernel compatibility enabled based on linux-next next-20100113 cfg80211: Calling CRDA to update world regulatory domain roboswitch: Probing device eth0: Failed to enable switch roboswitch: Probing device eth1: No such device roboswitch: Probing device eth2: No such device roboswitch: Probing device eth3: No such device cfg80211: World regulatory domain updated: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Broadcom 43xx driver loaded [ Features: PNL, Firmware-ID: FW13 ] PPP generic driver version 2.4.2 ip_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 24 nf_conntrack version 0.5.0 (210 buckets, 840 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. BusyBox v1.15.3 (2010-03-19 06:01:56 CET) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M BackFire (10.3-rc1, r20254) ----------------------- * 1/3 shot Kahlua In a shot glass, layer Kahlua * 1/3 shot Bailey's on the bottom, then Bailey's, * 1/3 shot Vodka then Vodka. --------------------------------------------------- root@OpenWrt:/#

Images

• from Technicolor
• 

  angled

• 

  top

• 

  back