Xiaomi MiWiFi 3 (R3)
Xiaomi MiWiFi 3 (R3) v1 (M26)
Manuf (OEM/ODM): Foxconn M30H021 T00
(Est.) release date: March 2016
Country of manuf.: China
Series: AC1200
Type: wireless router
FCC ID: none available
PCB ID: M30H021T00
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7620A (580 MHz)
FLA1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Spansion S34ML01G100TF100)
RAM1: 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (Nanya NT5TU64M16HG-AC)
Expansion IFs: USB 2.0
USB ports: 1
Serial: yes, 4-pin header
WI1 chip1: MediaTek MT7620A
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612E
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7620A
Switch: MediaTek MT7620A
LAN speed: 100M
LAN ports: 2
WAN speed: 100M
WAN ports: 1
abgn+ac
Stock bootloader: U-Boot 1.1.3
Stock FW OS: Linux 2.6.36
Default SSID: Xiaomi_XXXX (19 addl. devices)
, Xiaomi_XXXX_5G (16 addl. devices)
Default IP address: 192.168.31.1
the IP 192.168.31.1 is used by 20 additional devices
of which 19 are Xiaomi devices
802dot11 OUI: none specified
CPU1 brand | WI1 chip1 brand | WI2 chip1 brand | |
---|---|---|---|
Xiaomi MiWiFi 3 (R3) | MediaTek | MediaTek | MediaTek |
Xiaomi MiWiFi 3 Pro (R3P) | MediaTek | MediaTek | MediaTek |
Xiaomi MiWiFi 3A | MediaTek | MediaTek | MediaTek |
Xiaomi MiWiFi 3C | MediaTek | MediaTek | |
Xiaomi MiWiFi 3G (R3G) | MediaTek | MediaTek | MediaTek |
Xiaomi MiWiFi HD (R3D) | Qualcomm | Qualcomm Atheros | Qualcomm Atheros |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
Xiaomi MiWiFi R3
- Product page (CN)
Reviews
- PCB: M30H021T00 (Foxconn) M26_REV.0102
Models
- Xiaomi MiWiFi 3 (R3) • Xiaomi Router 3 • ToH
- Xiaomi MiWiFi HD (R3D) • Xiaomi Router HD
- FCC ID: 2AIMRMIWIFIR3D (2017-12-13)
- Xiaomi MiWiFi 3 Pro (R3P) • Xiaomi Router 3 Pro
- FCC ID: 2AIMRMIWIFIR3P (2017-08-22)
Serial
• OEM Boot log |
---|
Welcome to minicom 2.7 OPTIONS: I18n Compiled on Jan 1 2014, 17:13:19. Port /dev/ttyUSB0, 16:21:43 Press CTRL-A Z for help on special keys U-Boot 1.1.3 (Mar 16 2016 – 14:15:12) Board: Ralink APSoC DRAM: 128 MB Power on memory test. Memory size= 128 MB …OK! relocate_code Pointer at: 87fb8000 enable ephy clock…done. rf reg 29 = 5 SSC disabled. !!! nand page size = 2048, addr len=4 ..============================================ Ralink UBoot Version: 4.2.S.1 ——————————————– ASIC 7620_MP (Port5None) DRAM_CONF_FROM: Auto-detection DRAM_TYPE: DDR2 DRAM component: 1024 Mbits DRAM bus: 16 bit Total memory: 128 MBytes Flash component: NAND Flash Date:Mar 16 2016 Time:14:15:12 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =128 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 3: System Boot system code via Flash. Booting System 1 ..Erasing NAND Flash… Writing to NAND Flash… done ## Booting image at bc200000 … Image Name: MIPS OpenWrt Linux-2.6.36 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2616754 Bytes = 2.5 MB Load Address: 80000000 Entry Point: 80000000 …………………………………. Verifying Checksum … OK Uncompressing Kernel Image … OK commandline uart_en=0 factory_mode=0 mem=128m No initrd ## Transferring control to Linux (at address 80000000) … ## Giving linux memsize in MB, 128 Starting kernel … LINUX started… THIS IS ASIC [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.36 (jenkins@JenkinsServer) (gcc version 4.6.3 6) [ 0.000000] The CPU feqenuce set to 580 MHz [ 0.000000] PCIE: bypass PCIe DLL. [ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 [ 0.000000] disable all power about PCIe [ 0.000000] CPU revision is: 00019650 (MIPS 24Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty – disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00008000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00008000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa2 [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 uart_m [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys [ 0.000000] Writing ErrCtl register=0004a6ba [ 0.000000] Readback ErrCtl register=0004a6ba [ 0.000000] allocated 655360 bytes of page_cgroup [ 0.000000] please try ‘cgroup_disable=memory’ option if you don’t want memos [ 0.000000] Memory: 123440k/131072k available (3347k kernel code, 7632k rese) [ 0.000000] SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N1 [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.010000] Calibrating delay loop… 385.84 BogoMIPS (lpj=1929216) [ 0.220000] pid_max: default: 32768 minimum: 301 [ 0.220000] Mount-cache hash table entries: 512 [ 0.220000] Initializing cgroup subsys cpuacct [ 0.230000] Initializing cgroup subsys memory [ 0.230000] Initializing cgroup subsys net_cls [ 0.230000] devtmpfs: initialized [ 0.240000] NET: Registered protocol family 16 [ 0.240000] RALINK_GPIOMODE = 121b1c [ 0.240000] RALINK_GPIOMODE = 101b1c [ 0.440000] PPLL_CFG1=0xe44000 [ 0.450000] MT7620 PPLL lock [ 0.450000] PPLL_DRV =0x80080504 [ 0.650000] Deassert the PCIE0 RESET. [ 0.650000] start PCIe register access [ 1.150000] RALINK_RSTCTRL = 2400000 [ 1.160000] RALINK_CLKCFG1 = 75afffc0 [ 1.160000] [ 1.160000] *************** MT7620 PCIe RC mode ************* [ 1.660000] PCIE0 enabled [ 1.670000] init_rt2880pci done [ 1.670000] bio: create slab at 0 [ 1.680000] SCSI subsystem initialized [ 1.680000] usbcore: registered new interface driver usbfs [ 1.680000] usbcore: registered new interface driver hub [ 1.690000] usbcore: registered new device driver usb [ 1.690000] pci 0000:00:00.0: BAR 0: can’t assign mem (size 0x80000000) [ 1.700000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 1.700000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pre] [ 1.710000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 1.710000] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI] [ 1.720000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64b] [ 1.720000] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] [ 1.730000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pre] [ 1.730000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 1.740000] pci 0000:00:00.0: bridge window [io disabled] [ 1.740000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 1.750000] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pre] [ 1.750000] BAR0 at slot 0 = 0 [ 1.760000] bus=0x0, slot = 0x0 [ 1.760000] res[0]->start = 0 [ 1.760000] res[0]->end = 0 [ 1.760000] res[1]->start = 20200000 [ 1.770000] res[1]->end = 2020ffff [ 1.770000] res[2]->start = 0 [ 1.770000] res[2]->end = 0 [ 1.770000] res[3]->start = 0 [ 1.780000] res[3]->end = 0 [ 1.780000] res[4]->start = 0 [ 1.780000] res[4]->end = 0 [ 1.780000] res[5]->start = 0 [ 1.790000] res[5]->end = 0 [ 1.790000] bus=0x1, slot = 0x0 [ 1.790000] res[0]->start = 20000000 [ 1.790000] res[0]->end = 200fffff [ 1.800000] res[1]->start = 0 [ 1.800000] res[1]->end = 0 [ 1.800000] res[2]->start = 0 [ 1.800000] res[2]->end = 0 [ 1.810000] res[3]->start = 0 [ 1.810000] res[3]->end = 0 [ 1.810000] res[4]->start = 0 [ 1.810000] res[4]->end = 0 [ 1.820000] res[5]->start = 0 [ 1.820000] res[5]->end = 0 [ 1.820000] Switching to clocksource MIPS [ 1.830000] NET: Registered protocol family 2 [ 1.830000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 1.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 1.850000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 1.850000] TCP: Hash tables configured (established 4096 bind 4096) [ 1.860000] TCP reno registered [ 1.860000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 1.870000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 1.870000] NET: Registered protocol family 1 [ 3.280000] RT3xxx EHCI/OHCI init. [ 3.290000] msgmni has been set to 241 [ 3.290000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major ) [ 3.300000] io scheduler noop registered (default) [ 3.310000] RALINK_REG_PIO7140DATA b0000670 = 0 [ 3.410000] RALINK_REG_PIO7140DATA b0000670 = 2000000 [ 3.420000] Ralink gpio driver initialized [ 3.420000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 3.430000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A [ 3.430000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A [ 3.440000] init reset module! [ 3.450000] brd: module loaded [ 3.450000] !!! nand page size = 2048, addr len=4 [ 3.460000] ra_nand_init: alloc 1350, at 87d90000 , btt(87d910c0, 100), ranf0 [ 3.470000] Creating 13 MTD partitions on “ra_nfc”: [ 3.470000] 0x000000000000-0x000008000000 : “ALL” [ 3.500000] 0x000000000000-0x000000040000 : “Bootloader” [ 3.510000] 0x000000040000-0x000000080000 : “Config” [ 3.510000] 0x000000080000-0x0000000c0000 : “Bdata” [ 3.520000] 0x0000000c0000-0x000000100000 : “Factory” [ 3.530000] 0x000000100000-0x000000140000 : “crash” [ 3.530000] 0x000000140000-0x000000180000 : “crash_syslog” [ 3.540000] 0x000000180000-0x000000200000 : “reserved0” [ 3.540000] 0x000000200000-0x000000600000 : “kernel0” [ 3.550000] 0x000000600000-0x000000a00000 : “kernel1” [ 3.560000] 0x000000a00000-0x000002a00000 : “rootfs0” [ 3.560000] 0x000002a00000-0x000004a00000 : “rootfs1” [ 3.570000] 0x000004a00000-0x000008000000 : “overlay” [ 3.570000] rdm_major = 253 [ 3.580000] SMACCR1 — : 0x0000f0b4 [ 3.580000] SMACCR0 — : 0x2985a41d [ 3.580000] Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx desc! [ 3.590000] SMACCR1 — : 0x0000f0b4 [ 3.600000] SMACCR0 — : 0x2985a41d [ 3.600000] PROC INIT OK! [ 3.610000] PPP generic driver version 2.4.2 [ 3.610000] PPP MPPE Compression module registered [ 3.620000] NET: Registered protocol family 24 [ 3.620000] PPTP driver version 0.8.5 [ 3.630000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver [ 3.750000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller [ 3.760000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus nu1 [ 3.800000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 [ 3.820000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 [ 3.820000] hub 1-0:1.0: USB hub found [ 3.830000] hub 1-0:1.0: 1 port detected [ 3.830000] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver [ 3.860000] rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller [ 3.860000] rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus nu2 [ 3.870000] rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 [ 3.940000] hub 2-0:1.0: USB hub found [ 3.940000] hub 2-0:1.0: 1 port detected [ 3.950000] usbcore: registered new interface driver cdc_acm [ 3.950000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems s [ 3.960000] Initializing USB Mass Storage driver… [ 3.970000] usbcore: registered new interface driver usb-storage [ 3.970000] USB Mass Storage support registered. [ 3.980000] usbcore: registered new interface driver usbserial [ 3.980000] USB Serial support registered for generic [ 3.990000] usbcore: registered new interface driver usbserial_generic [ 4.000000] usbserial: USB Serial Driver core [ 4.000000] USB Serial support registered for pl2303 [ 4.010000] usbcore: registered new interface driver pl2303 [ 4.010000] pl2303: Prolific PL2303 USB to serial adaptor driver [ 4.020000] USB Serial support registered for TI USB 3410 1 port adapter [ 4.030000] USB Serial support registered for TI USB 5052 2 port adapter [ 4.030000] usbcore: registered new interface driver ti_usb_3410_5052 [ 4.040000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver [ 4.050000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_ma) [ 4.050000] u32 classifier [ 4.060000] input device check on [ 4.060000] Actions configured [ 4.060000] Netfilter messages via NETLINK v0.30 with ipset netlink.patch. [ 4.070000] nf_conntrack version 0.5.0 (1928 buckets, 7712 max) [ 4.080000] xt_time: kernel timezone is -0000 [ 4.080000] GRE over IPv4 demultiplexor driver [ 4.090000] ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Coe [ 4.100000] TCP cubic registered [ 4.100000] NET: Registered protocol family 10 [ 4.110000] NET: Registered protocol family 17 [ 4.110000] L2TP core driver, V2.0 [ 4.110000] PPPoL2TP kernel driver, V2.0 [ 4.120000] L2TP netlink interface [ 4.120000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 4.130000] All bugs added by David S. Miller <davem@redhat.com> [ 4.150000] Freeing unused kernel memory: 1188k freed [ 4.240000] Loading essential drivers… [ 4.250000] Press Ctrl+C to enter RAMFS… [ 5.260000] Check for USB recovery… [ 5.290000] Bringup the system… [ 5.300000] flag_boot_rootfs=0 mounting /dev/mtd10 [ 5.310000] UBI: attaching mtd10 to ubi0 [ 5.310000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 5.320000] UBI: logical eraseblock size: 126976 bytes [ 5.320000] UBI: smallest flash I/O unit: 2048 [ 5.330000] UBI: VID header offset: 2048 (aligned 2048) [ 5.340000] UBI: data offset: 4096 [ 5.490000] UBI: max. sequence number: 2 [ 5.500000] UBI: attached mtd10 to ubi0 [ 5.500000] UBI: MTD device name: “rootfs0” [ 5.510000] UBI: MTD device size: 32 MiB [ 5.510000] UBI: number of good PEBs: 256 [ 5.520000] UBI: number of bad PEBs: 0 [ 5.520000] UBI: max. allowed volumes: 128 [ 5.530000] UBI: wear-leveling threshold: 4096 [ 5.530000] UBI: number of internal volumes: 1 [ 5.540000] UBI: number of user volumes: 1 [ 5.540000] UBI: available PEBs: 0 [ 5.550000] UBI: total number of reserved PEBs: 256 [ 5.550000] UBI: number of PEBs reserved for bad PEB handling: 4 [ 5.560000] UBI: max/mean erase counter: 1/0 [ 5.560000] UBI: image sequence number: 1026081047 [ 5.570000] UBI: background thread “ubi_bgt0d” started, PID 80 UBI device number 0, total 256 LEBs (32505856 bytes, 31.0 MiB), available 0 LEB) [ 5.660000] UBIFS: mounted UBI device 0, volume 0, name “system” [ 5.660000] UBIFS: mounted read-only [ 5.670000] UBIFS: file system size: 30093312 bytes (29388 KiB, 28 MiB, 23) [ 5.670000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LE) [ 5.680000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 5.690000] UBIFS: default compressor: zlib [ 5.690000] UBIFS: reserved for root: 0 bytes (0 KiB) config core ‘version’ # ROM ver option ROM ‘2.8.12’ # channel option CHANNEL ‘release’ # hardware platform R1AC or R1N etc. option HARDWARE ‘R3’ # CFE ver option UBOOT ‘1.0.2’ # Linux Kernel ver option LINUX ‘0.1.12’ # RAMFS ver option RAMFS ‘0.1.12’ # SQUASHFS ver option SQAFS ‘0.1.12’ # ROOTFS ver option ROOTFS ‘0.1.12’ #build time option BUILDTIME ‘Wed, 16 Mar 2016 14:13:36 +0800’ #build timestamp option BUILDTS ‘1458108816’ #build git tag option GTAG ‘commit 17f50389a144da43f3858d508d9de41885282406’ mount: mounting proc on /proc failed: Device or resource busy mount: mounting sysfs on /sys failed: Device or resource busy [ 6.460000] Raeth v3.0 (Tasklet,SkbRecycle) [ 6.460000] [ 6.460000] phy_tx_ring = 0x074c7000, tx_ring = 0xa74c7000 [ 6.460000] [ 6.460000] phy_rx_ring0 = 0x07df0000, rx_ring0 = 0xa7df0000 [ 6.460000] SMACCR1 — : 0x0000f0b4 [ 6.460000] SMACCR0 — : 0x2985a41d [ 6.490000] CDMA_CSG_CFG = 81000000 [ 6.490000] GDMA1_FWD_CFG = 20710000 – preinit – Wed Mar 16 14:27:38 UTC 2016 – regular preinit – [ 6.670000] UBI: attaching mtd12 to ubi1 [ 6.670000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 6.680000] UBI: logical eraseblock size: 126976 bytes [ 6.680000] UBI: smallest flash I/O unit: 2048 [ 6.690000] UBI: VID header offset: 2048 (aligned 2048) [ 6.690000] UBI: data offset: 4096 [ 6.940000] UBI: max. sequence number: 122 [ 6.960000] UBI: attached mtd12 to ubi1 [ 6.960000] UBI: MTD device name: “overlay” [ 6.970000] UBI: MTD device size: 54 MiB [ 6.970000] UBI: number of good PEBs: 432 [ 6.980000] UBI: number of bad PEBs: 0 [ 6.980000] UBI: max. allowed volumes: 128 [ 6.990000] UBI: wear-leveling threshold: 4096 [ 6.990000] UBI: number of internal volumes: 1 [ 7.000000] UBI: number of user volumes: 1 [ 7.000000] UBI: available PEBs: 0 [ 7.000000] UBI: total number of reserved PEBs: 432 [ 7.010000] UBI: number of PEBs reserved for bad PEB handling: 8 [ 7.020000] UBI: max/mean erase counter: 1/0 [ 7.020000] UBI: image sequence number: 35629411 [ 7.030000] UBI: background thread “ubi_bgt1d” started, PID 149 UBI device number 1, total 432 LEBs (54853632 bytes, 52.3 MiB), available 0 LEB) [ 7.080000] UBIFS: recovery needed [ 7.130000] UBIFS: recovery completed [ 7.130000] UBIFS: mounted UBI device 1, volume 0, name “data” [ 7.140000] UBIFS: file system size: 52187136 bytes (50964 KiB, 49 MiB, 41) [ 7.140000] UBIFS: journal size: 2666496 bytes (2604 KiB, 2 MiB, 21 LE) [ 7.150000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 7.160000] UBIFS: default compressor: lzo [ 7.160000] UBIFS: reserved for root: 2464926 bytes (2407 KiB) /lib/preinit.sh: line 1: jffs2_not_mounted: not found – init – [ 7.760000] ra2880stop()…Done [ 7.780000] Free TX/RX Ring Memory! init started: BusyBox v1.19.4 (2016-03-16 14:06:55 CST) Please press Enter to activate this console. rcS S boot: INFO: rc script run ti. [ 8.800000] tntfs: module license ‘Commercial. For support email ntfs-suppor. [ 8.810000] Disabling lock debugging due to kernel taint [ 8.850000] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. [ 8.950000] Tuxera FAT 12/16/32 driver version 3014.1.24 [Flags: R/W MODULE]. [ 9.010000] tun: Universal TUN/TAP device driver, 1.6 [ 9.020000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 9.040000] Mirror/redirect action on [ 9.300000] GRE over IPv4 tunneling driver [ 9.530000] ipt: xt_cgroup_MARK installed ok. [ 9.600000] ip_set: protocol 6 [ 9.880000] sstack_init [ 11.170000] [ 11.180000] [ 12.720000] [ 12.740000] CSRBaseAddress =0xc1100000, csr_addr=0xc1100000! [ 12.750000] MAC_CSR0=1986146304, RtmpChipOpsHook [ 12.760000] dev idx = 1! [ 12.760000] get_dev_config_idx pAd->MACVersion = 76623000, pAd->ChipID4 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: INFO: loading exist /etc/config/ne. Wed Mar 16 22:27:44 CST 2016 netconfig[405]: #### Loopback configuration Wed Mar 16 22:27:44 CST 2016 netconfig[405]: config interface loopback Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ifname lo Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option proto static Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ipaddr 127.0.0.1 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option netmask 255.0.0.0 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: #### LAN configuration Wed Mar 16 22:27:44 CST 2016 netconfig[405]: config interface lan Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ifname eth0.1 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option type bridge Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option proto static Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ipaddr 192.168.31.1 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option netmask 255.255.255.0 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: #### WAN configuration Wed Mar 16 22:27:44 CST 2016 netconfig[405]: config interface wan Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ifname eth0.2 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option proto dhcp Wed Mar 16 22:27:44 CST 2016 netconfig[405]: ### IFB interface for MiQoS Wed Mar 16 22:27:44 CST 2016 netconfig[405]: config interface ifb Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option ifname ifb0 Wed Mar 16 22:27:44 CST 2016 netconfig[405]: #### READY configuration Wed Mar 16 22:27:44 CST 2016 netconfig[405]: config interface ready Wed Mar 16 22:27:44 CST 2016 netconfig[405]: option proto static Wed Mar 16 22:27:45 CST 2016 netconfig[405]: option ipaddr 169.254.29.1 Wed Mar 16 22:27:45 CST 2016 netconfig[405]: option netmask 255.255.255.0 [ 15.230000] Raeth v3.0 (Tasklet,SkbRecycle) [ 15.230000] [ 15.230000] phy_tx_ring = 0x05e6f000, tx_ring = 0xa5e6f000 [ 15.230000] [ 15.230000] phy_rx_ring0 = 0x05e5d000, rx_ring0 = 0xa5e5d000 [ 15.230000] SMACCR1 — : 0x0000f0b4 [ 15.230000] SMACCR0 — : 0x2985a41d [ 15.250000] CDMA_CSG_CFG = 81000000 [ 15.260000] GDMA1_FWD_CFG = 20710000 [ 15.280000] device eth0.1 entered promiscuous mode [ 15.290000] device eth0 entered promiscuous mode [ 15.310000] br-lan: port 1(eth0.1) entering learning state [ 15.310000] br-lan: port 1(eth0.1) entering learning state [ 16.020000] MAC_CSR0=1986146304, rtmp_asic_top_init [ 16.150000] Set_Bsd_Proc 7114 Bsd 0 [ 17.310000] br-lan: port 1(eth0.1) entering forwarding state [ 19.370000] <==== rt28xx_init, Status=0 [ 21.640000] device wl0 entered promiscuous mode [ 21.640000] br-lan: port 2(wl0) entering learning state [ 21.650000] br-lan: port 2(wl0) entering learning state [ 22.250000] Set_Bsd_Proc 6786 Bsd 0 [ 23.650000] br-lan: port 2(wl0) entering forwarding state |