FCC approval date: 07 September 2010
Country of manuf.: China
Power: 12 VDC, 0.5 A
Connector type: barrel
CPU1: Broadcom BCM6332 (240 MHz)
FLA1: 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Eon F16-100HIP)
RAM1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (EtronTech EM638165TS-6G)
Expansion IFs: none specified
Serial: yes, internal, 4-pin header, populated, 3.3V TTL, (115200,8,N,1), XJ1
ETH chip1: Broadcom BCM6332
LAN speed: 100M
LAN ports: 1
Additional chips
DSL (ADSL2+) Line Driver;Broadcom;BCM6301;BROADCOM, 6301KSG, TD1117P1;1;
2A, 18V Synchronous Rectified Step-Down Converter;MPS;MP1482DS;;1;
DC/DC Switching Regulator;ATC;AP34063;;1;
Stock bootloader: CFE 1.0.37-10.1 BCM96338
Stock FW OS: Linux 2.6.8.1
| CPU1 brand |
|---|
| ZTE ZXDSL 831B | Globespan Virata | 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
| ZTE ZXDSL 831CII | TrendChip | 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
| ZTE ZXDSL 831II | Broadcom | 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> | 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
ADSL CPE
- Product page
"AZ29C V1.0" is silkscreened on at least one 831II's board.
See also
ZTE ZXDSL 831CII (Chassis PCB - BZRD0 V1.0) 08/19/2010
- CPU: TrendChip TC3162U -LQ128G (U100)
- RAM: EtronTech EM638165TS-6G (8MB)
- Flash: Winbond 25Q16BVSIG (2MB)
- DSL AFE: TrendChip TC3086 -QFN64-EPG (U200)
- Ethernet Switch: TrendChip TC2205F (U300)
- PMU: MPS MP1482DS, ATC AP34063 (DC/DC)
Serial
Pinout
.. appears to be the following...
XJ1
(RxD) (TxD) (GND) (3.3)
<--- to BCM6332
Credentials
They're the same as the HTTP admin credentials.
Username: admin
Password: admin
Info derived from
| Expand • boot log
|
CFE version 1.0.37-10.1 for BCM96338 (32bit,SP,BE)
Build Date: Tue Jun 1 15:21:05 CST 2010 (unive@Unive)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
serial flash device: name EN25F16, id 0x1c14, size 2048KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x29010: 240MHz
Total memory: 8388608 bytes (8MB)
Total memory used by CFE: 0x80401000 - 0x805280C0 (1208512)
Initialized Data: 0x8041DA00 - 0x8041F8E0 (7904)
BSS Area: 0x8041F8E0 - 0x804260C0 (26592)
Local Heap: 0x804260C0 - 0x805260C0 (1048576)
Stack Area: 0x805260C0 - 0x805280C0 (8192)
Text (code) segment: 0x80401000 - 0x8041D9F8 (117240)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96332L-2M-8M
Number of MAC Addresses (1-32) : 11
Base MAC Address : b0:75:d5:48:b9:4a
PSI Size (1-64) KBytes : 24
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbfc10000) ...
Code Address: 0x80001000, Entry Address: 0x801a0018
Decompression OK!
Entry at 0x801a0018
Closing network.
Starting program at 0x801a0018
Linux version 2.6.8.1 (dailybuild@sh01.wireline)
(gcc version 3.4.2) #1 Mon Jun 21 17:21:42 CST 2010
serial flash device: name EN25F16, id 0x1c14, size 2048KB
96332L-2M-8M prom init
CPU revision is: 00029010
Determined physical RAM map:
memory: 007a0000 @ 00000000 (usable)
On node 0 totalpages: 1952
DMA zone: 1952 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 32 (order 5: 256 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 5844k/7808k available
(1446k kernel code, 1944k reserved, 209k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80600000 ... 0x80700000>
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 2048K with 512 sectors
File system address: 0xbfc10100
Can't analyze prologue code at 80169384
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
PressAndHoldReset interrupt[4] mapping succeeded!
Serial: BCM63XX driver $Revision: 1.1.1.1 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6338A2 Ethernet Network Device v0.3 Jun 21 2010 17:20:36
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: B0:75:D5:48:B9:4A
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2010.06.21-09:23+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2010.06.21-09:23+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
BcmAdsl_Initialize=0x800DE458, g_pFnNotifyCallback=0x80198804
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003981 adsl2=0x00000001
pSdramPHY=0xA07FFFF8, 0xFFFFFFFF 0xFFEFFFFF
AdslCoreHwReset: AdslOemDataAddr = 0xA07FB114
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003981 adsl2=0x00000001
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
app: atmctl start --pqs 125
ATM proc init !!!
app: atmctl operate vcc --add 0.8.81 aal5 1 llcencaps --addq 0.8.81 11 1
app: atmctl operate vcc --add 0.0.35 aal5 1 llcencaps --addq 0.0.35 11 1
app: atmctl operate vcc --add 0.8.35 aal5 1 llcencaps --addq 0.8.35 11 1
app: atmctl operate vcc --add 0.0.32 aal5 1 llcencaps --addq 0.0.32 11 1
app: atmctl operate vcc --add 0.0.100 aal5 1 llcencaps --addq 0.0.100 11 1
app: atmctl operate vcc --add 0.8.36 aal5 1 llcencaps --addq 0.8.36 11 1
app: atmctl operate vcc --add 0.0.33 aal5 1 llcencaps --addq 0.0.33 11 1
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (61 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_ipsec: module license 'Proprietary' taints kernel.
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
==> Bcm963xx Software Version: ZXDSL 831IIV7.5.5a_Z29_OV <==
app: brctl addbr br0
app: brctl stp br0 off
app: brctl setfd br0 0
app: ifconfig eth0 up
app: ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 up;
brctl addif br0 eth0; ifconfig eth0 0.0.0.0
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
app: sendarp -s br0 -d br0
app: sendarp -s br0 -d eth0
BcmRfc2684_init interface is not up nas_0_8_81!
pvc2684ctl -a -v 0.8.81 &
app: pvc2684ctl -a -v 0.8.81 &
pvc2684d: Interface "nas_0_8_81" created sucessfully
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
app: ifconfig nas_0_8_81 hw ether b0:75:d5:48:b9:4b
app: ifconfig nas_0_8_81 up
app: brctl addif br0 nas_0_8_81
device nas_0_8_81 entered promiscuous mode
br0: port 2(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 2(nas_0_8_81) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
app: pvc2684ctl -a -v 0.0.35 &
pvc2684d: Interface "nas_0_0_35" created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
app: ifconfig nas_0_0_35 hw ether b0:75:d5:48:b9:4c
app: ifconfig nas_0_0_35 up
app: brctl addif br0 nas_0_0_35
device nas_0_0_35 entered promiscuous mode
br0: port 3(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 3(nas_0_0_35) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_8_35!
pvc2684ctl -a -v 0.8.35 &
app: pvc2684ctl -a -v 0.8.35 &
pvc2684d: Interface "nas_0_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
app: ifconfig nas_0_8_35 hw ether b0:75:d5:48:b9:4d
app: ifconfig nas_0_8_35 up
app: brctl addif br0 nas_0_8_35
device nas_0_8_35 entered promiscuous mode
br0: port 4(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 4(nas_0_8_35) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_0_32!
pvc2684ctl -a -v 0.0.32 &
app: pvc2684ctl -a -v 0.0.32 &
pvc2684d: Interface "nas_0_0_32" created sucessfully
pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC
app: ifconfig nas_0_0_32 hw ether b0:75:d5:48:b9:4e
app: ifconfig nas_0_0_32 up
app: brctl addif br0 nas_0_0_32
device nas_0_0_32 entered promiscuous mode
br0: port 5(nas_0_0_32) entering learning state
br0: topology change detected, propagating
br0: port 5(nas_0_0_32) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_0_100!
pvc2684ctl -a -v 0.0.100 &
app: pvc2684ctl -a -v 0.0.100 &
pvc2684d: Interface "nas_0_0_100" created sucessfully
pvc2684d: Communicating over ATM 0.0.100, encapsulation: LLC
app: ifconfig nas_0_0_100 hw ether b0:75:d5:48:b9:4f
app: ifconfig nas_0_0_100 up
app: brctl addif br0 nas_0_0_100
device nas_0_0_100 entered promiscuous mode
br0: port 6(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_0_100) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_8_36!
pvc2684ctl -a -v 0.8.36 &
app: pvc2684ctl -a -v 0.8.36 &
pvc2684d: Interface "nas_0_8_36" created sucessfully
pvc2684d: Communicating over ATM 0.8.36, encapsulation: LLC
app: ifconfig nas_0_8_36 hw ether b0:75:d5:48:b9:50
app: ifconfig nas_0_8_36 up
app: brctl addif br0 nas_0_8_36
device nas_0_8_36 entered promiscuous mode
br0: port 7(nas_0_8_36) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_8_36) entering forwarding state
app: sendarp -s br0 -d br0
BcmRfc2684_init interface is not up nas_0_0_33!
pvc2684ctl -a -v 0.0.33 &
app: pvc2684ctl -a -v 0.0.33 &
pvc2684d: Interface "nas_0_0_33" created sucessfully
pvc2684d: Communicating over ATM 0.0.33, encapsulation: LLC
app: ifconfig nas_0_0_33 hw ether b0:75:d5:48:b9:51
app: ifconfig nas_0_0_33 up
app: brctl addif br0 nas_0_0_33
device nas_0_0_33 entered promiscuous mode
br0: port 8(nas_0_0_33) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_33) entering forwarding state
app: sendarp -s br0 -d br0
****** cfm init end! ******
br0: port 1(eth0) entering disabled state
|
cat /proc/cpuinfo
> cat /proc/cpuinfo
system type : 96332L-2M-8M
processor : 0
cpu model : BCM6338 V1.0
BogoMIPS : 239.20
wait instruction : no
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : no
unaligned access : 11
VCED exceptions : not available
VCEI exceptions : not available
ps aux
> ps aux
PID Uid VmSize Stat Command
1 admin 216 S init
2 admin SWN [ksoftirqd/0]
3 admin SW< [events/0]
4 admin SW< [khelper]
5 admin SW< [kblockd/0]
6 admin SW [pdflush]
7 admin SW [pdflush]
8 admin SW [kswapd0]
9 admin SW< [aio/0]
10 admin SW [mtdblockd]
17 admin 292 S -sh
41 admin 972 S cfm
211 admin 196 S pvc2684d
422 admin 1108 S httpd
473 admin 1024 S consoled
478 admin 264 S sh -c ps aux
479 admin 252 R ps aux
cat /proc/meminfo
> cat /proc/meminfo
MemTotal: 5936 kB
MemFree: 332 kB
Buffers: 408 kB
Cached: 2156 kB
SwapCached: 0 kB
Active: 1580 kB
Inactive: 1476 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 5936 kB
LowFree: 332 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
Mapped: 1600 kB
Slab: 548 kB
Committed_AS: 1884 kB
PageTables: 140 kB
VmallocTotal: 1048560 kB
VmallocUsed: 588 kB
VmallocChunk: 1047968 kB
cat /proc/mtd
> cat /proc/mtd
dev: size erasesize name
mtd0: 00144000 00004000 "Physically mapped flash"
