Belkin F7D2301

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Belkin F7D2301 v1

Manuf (OEM/ODM): Arcadyan WG7005E22 2-LF-AK

FCC approval date: 12 February 2010
(Est.) release date: 24 March 2010
UPC: 722868757307 (UPC DB, On eBay)
Country of manuf.: China

Amazon image

ASIN
B003CJTNJ0 (Flag of the United States.svg, On Amazon, On CCC)

Type: wireless router

FCC ID: K7SF7D2301V1
IC ID: 3623A-F7D2301V1
PCB ID: 141700520021J

Power: 9 VDC, 1 A
Connector type: barrel
Conn. measurements: 5.5 mm (OD), 3 mm (ID), 10.5 mm (LEN)

CPU1: Ralink RT3052 (384 MHz)
FLA1: 2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Macronix MX25L1605AM2I)
RAM1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (EtronTech EM638165TS-5G)

Expansion IFs: none specified
JTAG: yes, probably, U5
Serial: yes, internal, Arcadyan type1 pinout, unpopulated, 3.3V TTL, (115200,8,N,1), J2

WI1 chip1: Ralink RT3052
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none

ETH chip1: Ralink RT3052
Switch: Ralink RT3052
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1

bgn

Additional chips
2.4GHz Power Amplifier IC;Richwave;RTC6691;187, 6691, A951;2;

Stock FW OS: SuperTask!

Default SSID: Belkin.XXXX (6 addl. devices)
Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 295 additional devices
of which 97 are Belkin devices

802dot11 OUI: 94:44:52 (17 E, 22 W)
Ethernet OUI: 94:44:52 (17 E, 22 W)

 FCC ID
Belkin F7D6301 v1K7SF7D2301V1

For a list of all currently documented Ralink chipsets with specifications, see Ralink.


Surf Wireless Router

 • Support page

Silkscreened text...

  • "P/N: 141700520021J R0B" appears to be silkscreened on the main board.
  • "P/N: 141700520021J R01" is silkscreened on a production model board.

The default SSID is Belkin.XXXX where XXXX appears to 3 followed by the last three

hex digits of the wireless interface MAC address (though this could be incorrect).

An example SSID is Belkin.336D with MAC 94:44:52:1E:93:6D.

PSU

The power adapter included with the router is a HXY-090V1330A (9V/1A).

ID/OD/Len measurements are approximate.

Serial

Pinout

Presumably the following standard Arcadyan pinout...

(3.3) (GND)
(   ) (   )
(   ) (TxD)
(   ) (RxD)
(   ) [   ]
J2

Info derived from

 • boot log • >>
=======================================================================
Wireless Router WG7005E22 2-LF-AK Loader v0.01 build Jul 31 2009 19:09:21
                    Arcadyan Technology Corporation
=======================================================================

AT25DF321

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...
Flash Checking
 Passed.
 failed : 4 !!
Unzipping firmware at 0x80002000 ... [ZIP 3] [ZIP 1]  done
In c_entry() function ...
CPU : RT3052  Chip V1.3, CPU Speed 384 MHz,
Interrups Status 00000000
install_exception
Co config = 80010483
sys_irq_init ...
enter start_ralink_timer - 2
##### _ftext      = 0x80002000
##### _fdata      = 0x802061D0
##### __bss_start = 0x8024AC6C
##### end         = 0x8079CAC0
##### Backup Data from 0x802061D0 to 0x807A4AC0~0x807E955C len 281244
##### Backup Data completed
##### Backup Data verified
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 384000000 Hz
mips_counter_frequency:192000000
r4k_offset: 0x0002ee00(192000)
init_US_counter : time1 = 299981 , time2 = 32300019, diff 32000038
US_counter = 59
 cnt1 33401861 cnt2 33403101, diff 1240
mips_int_enable: 5
mips_int_enable 1: s = 8401
mips_int_enable 2: s = 8401
mips_int_enable 3: s = 0
Runtime code version: 1.00.16
System startup...
[INIT] Memory COLOR 0, 730000 bytes ..
[INIT] Memory COLOR 1, 400000 bytes ..
[INIT] Memory COLOR 2, 351200 bytes ..
Set flash memory layout to Boot Parameters found !!!
Bootcode version: v0.01
Serial number: 121010G2102975
Hardware version: 01


sizeof(struct III_Config_t) is 64748, nLen:64748, Magic:0xffffffff
!![E-CFG-VER] Configuration data version mismatch!!
!![E-CFG-VER] Adapting factory defaults!!
!![E-CFG-VER] Reconfiguration required!!
!!No configuration file present!!
!!! Invalid wireless channel range 0 ~ 0
!!! Use default value 1 ~ 13
default route: 0.0.0.0
BufferInit:
BUF_HDR_SZ=128 BUF_ALIGN_SZ=0 BUFFER_OFFSET=352
BUF_BUFSZ0=608 BUF_BUFSZ1=4320
NUM_OF_B0=0 NUM_OF_B1=300
BUF_POOL0_SZ=0 BUF_POOL1_SZ=1334400
sizeof(BUFFER0)=736,sizeof(BUFFER1)=4448
*BUF0=0x8058fdcc *BUF1=0x8044a12c
Altgn *BUF0=0x8058fde0 *BUF1=0x8044a140
End at BUF0:0x8058fde0, BUF1:0x8058fdc0

buffer0 pointer init OK!
buffer1 pointer init OK!
ifno=  0, Link_Type= 4
time = 08/01/2003, 00:00:00
Interface 0 ip = 127.0.0.1

ifno=  1, Link_Type= 1
need to reset Ethernet switch????
GDMA1_MAC_ADRH -- : 0x00009444
GDMA1_MAC_ADRL -- : 0x521e936d
RA2880 Ethernet Driver Initilization. v1.60  64 rx/tx descriptors allocated.
NAPI enable, Tx Ring = 64, Rx Ring = 64
phy_tx_ring = 0x0024b890, tx_ring = 0xA024B890, size: 16 bytes

phy_rx_ring = 0x0024bc90, rx_ring = 0xA024BC90, size: 16 bytes
GDMA1_FWD_CFG = 10000
mips_int_enable: 3
mips_int_enable 1: s = 8400
mips_int_enable 2: s = a400
mips_int_enable 3: s = 0
MAC Address: 94:44:52:1e:93:6d
time = 08/01/2003, 00:00:00
Interface 1 ip = 192.168.2.1

ifno=  2, Link_Type= 1
hwlan_init(384): [HWLAN] ifno=2 irno=7 port=0x00000000
2860 version : 2.0.0.0 (Jul  2 2010)
Enter rbus_module_init
Enter alloc_netdev
RTMP_ADAPTER_mem : 802a8d2c, sizeof(RTMP_ADAPTER) 110328


=== pAd = 802A8D2C, size = 110328 ===

wlan security on!
RUNTASK id=1 hwlan_light_isr...
RUNTASK id=2 InternetCheckTask...
time = 08/01/2003, 00:00:00
Interface 2 ip = 192.168.2.1

ifno=  3, Link_Type= 1
MAC Address: 94:44:52:1e:93:6e
time = 08/01/2003, 00:00:00
iput_IpLinkUp(ifno=3)> ifp->add_default_route:1
Init NAT data structure
Interface 3 ip = 0.0.0.0

ifno=  4, Link_Type= 0
ifno=  5, Link_Type= 0
ifno=  6, Link_Type= 0
ifno=  7, Link_Type= 0
ruleCheck()> Group: 0,  Error: Useless rule index will be truncated
ruleCheck()> Group: 1,  Error: Useless rule index will be truncated
ruleCheck()> Group: 2,  Error: Useless rule index will be truncated
ruleCheck()> Group: 3,  Error: Useless rule index will be truncated
CBAC rule format check succeed !!
reqCBACBuf()> init match pool, Have: 50
Memory Address: 0x807828ac ~ 0x80782e40
reqCBACBuf()> init timeGap pool, Have: 2000
Memory Address: 0x80782e40 ~ 0x8078ca94
reqCBACBuf()> init sameHost pool, Have: 1000
Memory Address: 0x8078ca94 ~ 0x807947b4
[setClsfyEnable] clsfy_func=0
CBAC rule pool initialized !!
Init NAT data structure
No default route, no need to reinit the NAT data structure
RUNTASK id=3 if_task if0...
RUNTASK id=4 if_task if1...
RUNTASK id=5 if_task if2...
RUNTASK id=6 if_task if3...
RUNTASK id=7 timer_task...
RUNTASK id=8 conn_mgr...
RUNTASK id=9 main_8021x...
RUNTASK id=10 main_lltd...
RUNTASK id=11 period_task...
RUNTASK id=12 dhcp_daemon...
RUNTASK id=13 dhcp_clt...on interface 3
RUNTASK id=14 pptp_callmgr...
Unzipping from BFC40000 to BFC40000 ... failed(4)
done
Uncompressed size = 0
httpd: listen at 192.168.2.1:80
RUNTASK httpd...
RUNTASK id=17 dnsproxy...
RUNTASK id=18 rip...
RUNTASK id=19 ripout...
RUNTASK id=20 dhcpd_mgmt_task...
UPnP is enabled
UPNP Device initialize success! slot=21

>>> belkin_wan_cfg task runs successfully, task_id = 22
gConfig.WSC_Mode:1
RUNTASK id=23 wscmain...
RUNTASK id=24 wsc_Send_eap_packet...
RUNTASK id=25 wsc_Send_UPNP_packet...
RUNTASK id=26 WSC_WaitUserAction_Task...
gConfig.WSC_Mode:1
UART RX Input
Starting Multitask...
load_lang_table to : English.cpz
Unzipping from 8066CA0C to 8064F20C ... [ZIP] done
Uncompressed size = 84265
get_language /www/doc/English.cpz, size=84265, >>>>>>>>
run_project_task
RUNTASK id=27 apAppInit...
ifno2dot1x_if[2]=0
dot1x_wireless_if_mask=0x4
RUNTASK id=28 Atheros_NetTask ...
mips_int_enable: 4
mips_int_enable 1: s = a400
mips_int_enable 2: s = e400
mips_int_enable 3: s = 0
rt2860_open : should call request_irq ????????????????????????
RX DESC A0254E90  size = 1024
sizeof(RT2860AP_DAT) : 1314
SSID = Belkin.336D len = 11
Channel=1
1. Phy Mode = 9
2. Phy Mode = 9
sould check E2PROM MAC ?????????????????
3. Phy Mode = 9
MCS Set = ff ff 00 00 00
Main bssid = 94:44:52:1e:93:6d
should Set up the Mac address ?????????
0x1300 = 00064380
netif_carrier_on() called ???
apAppInit : dev->flags  00000001
[HWLAN] Ready
[dhcp_clt] enable dhcp client in interface WAN[3]
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.02, Jul  2 2010 14:36:38
*********************************************
Initializing stack...
---------in wsc init----------
----------sizeof(uint32)=4
----------sizeof(uint-long)=4
----------sizeof(uint32)=2
@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@
wsc_Send_eap_packet:udpFdupnp_wcn:16;;udpFdupnp:18
WSC_WaitUserAction:wait user action:0
[HWLAN] [29] rapi_tmr_task running
[23]pthread_cond_init: 0
[23]pthread_mutex_init: resource No. 33
[23]pthread_mutex_init: resource No. 34
[PORTABLITY]:WscCreateThread--------------------
 Entered udp_read
WscCmd:ActualCBThreadProc: Started
upnp_Init: flag=0
SSDP Initialization completed...
GenaInit : event_hook is NULL!!
[htf_dbg]     - OnlineActiveWirless() 1852
end of OnlineActiveWirless
[23]pthread_cond_init: 1
[23]pthread_mutex_init: resource No. 35
[23]pthread_mutex_init: resource No. 36
[PORTABLITY]:WscCreateThread--------------------
 WscCmd:ActualUIThreadProc: Started.
ActualUIThreadProc: wait q
[reset_802dot1x] wireless module ready
[init_wpa] dot1x_ready[0]=3
[reset_802dot1x] 802.1Xv2 ready
MasterControl constructor
WscCmd::MC instantiated ok
[23]pthread_cond_init: 2
[23]pthread_mutex_init: resource No. 37
[23]pthread_mutex_init: resource No. 38
[PORTABLITY]:WscCreateThread--------------------
 [23]pthread_mutex_init: resource No. 39
[PORTABLITY]:pthread_mutex_init--------------------
 CTransport Construction
[23]pthread_cond_init: 3
[23]pthread_mutex_init: resource No. 40
[23]pthread_mutex_init: resource No. 41
[PORTABLITY]:WscCreateThread--------------------
 In CTransport::ActualCBThreadProc
ActualCBThreadProc: Calling Dequeue
MC::Init: Init complete ok
WscCmd::MC intialized ok
WscCmd::Init ok, starting stack...
Info::ReadConfigFile: Called
Info::ReadConfigFile:H▒▒
Info::ReadConfigFile:File open ok
******************uuid_p:0x000000000000000110009444521e936d*****
mp_deviceInfo->uuid[i]:
0-0-0-0-0-0-0-1-10-0-94-44-52-1e-93-6d-
mp_deviceInfo->macAddr:94:44:52:1E:93:6D
gSetting.dot1x.if_entry[0].enableWEP:0
authTypeFlags is 2 ,encrTypeFlags is 8 ,m_nwKey is 642BA35D, key len is 8
 ssid is Belkin.336D
S, ef7
E, 10f7
RegistrarSM constructor
[23]pthread_cond_init: 4
[23]pthread_mutex_init: resource No. 42
[23]pthread_mutex_init: resource No. 43
[PORTABLITY]:WscCreateThread--------------------
 [23]pthread_mutex_init: resource No. 44
[PORTABLITY]:pthread_mutex_init--------------------
 RegistrarSM constructor
[23]pthread_cond_init: 5
[23]pthread_mutex_init: resource No. 45
[23]pthread_mutex_init: resource No. 46
[PORTABLITY]:WscCreateThread--------------------
 c_devPwd:org:33183800
**************mcp_devPwd:33183800;;
Generated devPwd:
in startMonitor....
CInbEap Construction
Sizeof(WSC_NOTIFY_DATA) = -2143633624
---test--sizeof(WSC_NOTIFY_DATA) = 36
[23]pthread_cond_init: 6
[PORTABLITY]:WscCreateEvent--------------------
 Entered udp_open
Socket open successful, sd: -2143633640
Entered udp_open
Socket open successful, sd: -2143633640
Entered udp_bind
Binding successful for socket [-2143633656]
[PORTABLITY]:WscCreateThread--------------------
 In CInbEap::StaticRecvThread
CInbEap::ActualRecvThread Started
Entered udp_read
in startMonitor....
CInbUPnPDev Construction
Entered udp_open
Socket open successful, sd: -2143633640
Entered udp_open
Socket open successful, sd: -2143633640
Entered udp_bind
Binding successful for socket [-2143633656]
CInbUPnPDev StartMonitor
[PORTABLITY]:WscCreateThread--------------------
 MC::SwitchModeOn: Exit
In CInbUPnPDev::StaticUPnPThread
end UPnPCreateMicroStack
Entered udp_read
MC::StartStack: Informing app of mode
-WscCmd::CallbackProc Enqueue done
MC::SwitchModeOn: Done callback
exit wscmain
@@[30]pthread_mutex_unlock: the res is free 33-- -2145414164
WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd

******* MODE: Access Point *******
-@@[27]pthread_mutex_unlock: the res is free 35-- -2144517096
*******p_header->eType:1

Options:
0. Quit
1. Get configured
2. Get configured via push-button
3. Get configured using IEs
Enter selection: ***gp_mc->mp_info->GetSwitchMode():1
mp_info->GetSwitchMode():1:e_currMode:1,,e_targetMode:3
mp_deviceInfo->authTypeFlags:2
mp_deviceInfo->encrTypeFlags:8
********cp_devPwd:33183800*****
mp_deviceInfo->authTypeFlags:2
MC::SetBeaconIE: call to trans->SetBeaconIE() ok
MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
Waiting for Registrar to connect...
WscCmd::unconfig initiated
ActualUIThreadProc: wait q