D-Link DWA-130 rev E1
D-Link DWA-130 E1
Manuf (OEM/ODM): Cameo
FCC approval date: 22 May 2009
Country of manuf.: China
Interface: USB
USB 2.0
Connector: Male A
Form factor tags: dongle
ID: 07d1:3300
Windows: USB\VID_07D1&PID_3300
FCC ID: KA2WA130E1
IC ID: 4216A-WA130E
WI1 chip1: Realtek RTL8191SU
Probable Linux driver
r8712u (w/ the fullmac rtl8192su driver under development)
see also Joshua Roys' mac80211-based driver work
USB ID not yet observed in any mainline kernel /
this list (note: outdated)
(see also passys)
Windows driver
possibly see Realtek's website
Antenna connector: none
bgn, 1x2:2
FCC ID | |
---|---|
Fry's Electronics FR-300USB rev A1 | KA2WA130E1 |
Chip1 brand | Chip2 brand | |
---|---|---|
D-Link DWA-130 rev A1 | Marvell | Marvell |
D-Link DWA-130 rev B1 | Ralink | Ralink |
D-Link DWA-130 rev C1 | Realtek | Realtek |
D-Link DWA-130 rev C2 | Realtek | |
D-Link DWA-130 rev D | Atheros | Atheros |
D-Link DWA-130 rev E1 | Realtek |
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Wireless N USB Adapter
• Support page
5.10 Drivers here
These support the following devices:
DWA-130C2: USB\VID_07D1&PID_3302
DWA-130E1: USB\VID_07D1&PID_3300
DWA-131A1: USB\VID_07D1&PID_3303
On card labeled "DWA-131, P/N AWA131AU E1G", Linux kali 4.19.0-kali3-amd64 #1 SMP Debian 4.19.20-1kali1 (2019-02-14) x86_64 GNU/Linux
iw list
Wiphy phy1 max # scan SSIDs: 4 max scan IEs length: 2257 bytes max # sched scan SSIDs: 0 max # match sets: 0 max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 RTS threshold: 2347 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 (00-0f-ac:4) * CCMP-256 (00-0f-ac:10) * GCMP-128 (00-0f-ac:8) * GCMP-256 (00-0f-ac:9) Available Antennas: TX 0 RX 0 Supported interface modes: * managed * monitor Band 1: Capabilities: 0x6c HT20 SM Power Save disabled RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT TX/RX MCS rate indexes supported: 0-15, 32 Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps * 5.5 Mbps * 11.0 Mbps * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (no IR) * 2472 MHz [13] (20.0 dBm) (no IR) * 2484 MHz [14] (20.0 dBm) (no IR) Supported commands: * new_interface * set_interface * new_key * start_ap * new_station * new_mpath * set_mesh_config * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * frame * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * probe_client * set_noack_map * register_beacons * start_p2p_device * set_mcast_rate * connect * disconnect * set_qos_map * set_multicast_to_unicast Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * P2P-device: 0x40 0xd0 software interface modes (can always be added): * monitor interface combinations are not supported HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. Device supports SAE with AUTHENTICATE command Device supports low priority scan. Device supports scan flush. Device supports AP scan. Device supports per-vif TX power setting Driver supports full state transitions for AP/GO clients Driver supports a userspace MPM Device supports configuring vdev MAC-addr on create. Supported extended features: * [ RRM ]: RRM * [ FILS_STA ]: STA FILS (Fast Initial Link Setup) * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211