Linksys WRT3200ACM
Linksys WRT3200AC M v1
Availability: now
Manuf (OEM/ODM): Wistron NeWeb
FCC approval date: 21 September 2016
(Est.) release date: 18 May 2016
(Est.) initial retail price (in USD): $249.99
Country of manuf.: China
Series: AC3200
Type: wireless router
FCC ID: Q87-WRT3200ACM
IC ID: 3839A-WRT3200ACM
PCB ID: 48SAM203.SGD
Power: 12 VDC, 3 A
Connector type: barrel
CPU1: Marvell 88F6820 (1.8 GHz, 2 cores)
FLA1: 256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (Spansion S34ML02G2)
FLA2: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (Winbond SPI × 2)
RAM1: 512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (Micron DDR3 × 2)
RAM2: 256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (Micron DDR3 × 2)
Expansion IFs: USB 3.0, USB 2.0 / eSATA (combo port)
USB ports: 2
SATA ports: 1
JTAG: yes, 20-pad header
Serial: yes, 6-pin header
WI1 chip1: Marvell 88W8964
WI1 chip2: Marvell 88W8887
WI1 802dot11 protocols: an+ac
WI1 MIMO config: 4x4:3
WI1 antenna connector: U.FL, RP-SMA
WI2 chip1: Marvell 88W8964
WI2 802dot11 protocols: bgn
WI2 MIMO config: 4x4:3
WI2 antenna connector: U.FL, RP-SMA
ETH chip1: Marvell 88F6820
Switch: Marvell 88E6352
LAN speed: 1G
LAN ports: 4
WAN speed: 1G
WAN ports: 1
abgn+ac
Additional chips
2.4GHz Front End Module;Skyworks;SKY85309-11;;4;
5GHz Front End Module;Skyworks;SKY85728-11;;4;
Stock bootloader: U-Boot
Stock FW OS: Linux 3.10.70
TPFirmware supported: DD-WRT • (List), OpenWrt • (List | Dev | DLs), LEDE Project (obsolete, OpenWrt) • (List), McDebian
Flags: Wave2, MU-MIMO, VHT160, DFS
Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1304 additional devices
of which 154 are Linksys devices
FCC ID | |
---|---|
Linksys WRT32X | Q87-WRT3200ACM |
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
- • 2600 Mbps - 3-stream 802.11ac device (160MHz bandwidth, 867Mbps/stream),
- • 600 Mbps - max. PHY rate for the 40MHz wide 2.4GHz channel = 3200 Mbps class
AC3200 MU-MIMO Gigabit Wi-Fi Router
"48SAM203.SGD" and "2016.05.18" is silkscreened on the board.
- Linksys WRT3200ACM (Rango) FCC ID: Q87-WRT3200ACM
Specifications
- CPU: Marvell 88F6820-A0 C180 @1.8GHz (Armada 385)
- Flash: AMD / Spansion 256MB (NAND), RAM: 512MB (DDR3)
- WLAN: 2x Marvell 88W8964 4T4R 802.11abgn/ac (MU-MIMO)
- Uses a 12V / 3A power adapter
Wikis
- WRT3200ACM - Marvell Armada 385 @1.8GHz (Rango)
Reviews
- • CPU: Marvell 88F6820-A0 C180 @1.8GHz (Armada 385 ARMv7)
- • 2.4GHz Radio: Marvell 88W8964-BTW2 WiSoC (MU-MIMO)
- 4x Skyworks SKY85309-11 2.4GHz Front End Module
- Micron 128MB DDR3 RAM
- • 5GHz Radio: Marvell 88W8964-BTW2 WiSoC (MU-MIMO)
- • Switch: Marvell 88E6352 GbE Switch
Forum threads
- Linksys WRT3200ACM ?? on DD-WRT forums
- Linksys WRT-3200ACM - The Big Blue Router Hits Wave 2 on SNB forums
- Linksys WRT3200ACM USB to TTL Connection on SNB forums
- Increased memory usage on WRT3200ACM on mwlwifi
Serial
• Boot log >> • |
---|
BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed Detected Device ID 6820 High speed PHY - Version: 2.0 Init RD NAS topology Serdes Lane 3 is USB3 Serdes Lane 4 is SGMII board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 6 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | | 4 | 5 | PCIe1 | | 5 | 0 | SGMII2 | ------------------------------- :** Link is Gen1, check the EP capability PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities :** Link is Gen1, check the EP capability PCIe, Idx 1: remains Gen1 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01 (Apr 08 2016 - 15:47:50) Marvell version: 2015_T1.QA.0p16 Boot version : v0.0.4 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1866 [MHz] L2 @ 933 [MHz] TClock @ 200 [MHz] DDR3 @ 933 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: 256 MiB MMC: mv_sdh: 0 DEVINFO offset == 0x7e0000 U-ENV offset == 0x200000 U-ENV offset == 0x200000 S-ENV offset == 0x220000 #### auto_recovery #### [u_env] get auto_recovery == yes [u_env] get auto_recovery == yes [u_env] get boot_part == 1 [u_env] get boot_part_ready == 3 auto_recovery enabled:1, boot_part:1, boot_part_ready:3 S-ENV offset == 0x220000 [boot_count_read] block:0x220000, size:128KB, records:64 [boot_count_read_record] boot_count:2, next_record:9 [boot_count_write] erase:0, auto_recovery-> block_offset:0x220000 offset=0x224800 Updating boot_count ... [boot_count_write] offset:0x224800 , length:2048 done PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1 USB2.0 0: Host Mode USB3.0 1: Host Mode USB3.0 0: Host Mode Map: Code: 0x1feab000:0x1ff75a20 BSS: 0x1ffef164 Stack: 0x1f9aaf20 Heap: 0x1f9ab000:0x1feab000 U-ENV offset == 0x200000 U-ENV offset == 0x200000 U-Boot Environment: 0x00200000:0x00220000 (NAND) Board configuration detected: mvEthE6171SwitchBasicInit init Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | | egiga1 | SGMII | 0x00 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 auto_recovery_check changes bootcmd: run nandboot Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xa00000, size 0x600000 6291456 bytes read: OK ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linksys WRT3200 Router Created: 2016-08-26 0:55:45 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4659771 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.70 (root@build-vm) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Thu Aug 25 17:55:29 PDT 2016 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 7 pages/cpu @c1162000 s7488 r8192 d12992 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env), 256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m (rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg) PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) allocated 1048576 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 508716k/508716k available, 15572k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc084ccd4 (8468 kB) .init : 0xc084d000 - 0xc088ed40 ( 264 kB) .data : 0xc0890000 - 0xc08e4260 ( 337 kB) .bss : 0xc08e4260 - 0xc09ab18c ( 796 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.70-2015_T1.1p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 3726.54 BogoMIPS (lpj=18632704) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 Initializing cgroup subsys memory CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Calibrating local timer... 933.29MHz. Setting up static identity map for 0xc064cc58 - 0xc064ccb0 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (7453.08 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 3309.200 MB/sec 8regs : 2234.400 MB/sec 32regs : 1905.600 MB/sec xor: using function: arm4regs (3309.200 MB/sec) pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 232 MB/s raid6: int32x2 344 MB/s raid6: int32x4 437 MB/s raid6: int32x8 444 MB/s raid6: using algorithm int32x8 (444 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.6: PCIe0.0: link up mvebu-pcie pcie-controller.6: PCIe1.0: link up mvebu-pcie pcie-controller.6: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers disabled PCI: bus2: Fast back to back transfers disabled pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref] pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref] pci 0000:00:02.0: PCI bridge to [bus 02] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Switching to clocksource armada_370_xp_clocksource cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. fuse init (API version 7.22) msgmni has been set to 993 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled ahci_mv f10a8000.sata: AHCI 1.0 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 11 cmdlinepart partitions found on MTD device armada-nand Creating 11 MTD partitions on "armada-nand": 0x000000000000-0x000000200000 : "uboot" 0x000000200000-0x000000220000 : "u_env" 0x000000220000-0x000000260000 : "s_env" 0x0000007e0000-0x000000820000 : "devinfo" 0x000000820000-0x000000a00000 : "sysdiag" 0x000000a00000-0x000005a00000 : "kernel" 0x000001000000-0x000005a00000 : "rootfs" 0x000005a00000-0x00000aa00000 : "alt_kernel" 0x000006000000-0x00000aa00000 : "alt_rootfs" 0x000000a00000-0x00000aa00000 : "ubifs" 0x00000aa00000-0x000010000000 : "syscfg" bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe0c00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=60:38:e0:b4:47:a0 (hw config) port #2: is_sgmii=1, is_rgmii=0, phy_addr=1 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o eth1, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=e2:d5:94:2f:af:12 (random) (error) mv_switch_probe(5780) (rc=-22): read switch fdt file failed mv_soho_switch: probe of switch.3 failed with error 1 o Loading Switch QuarterDeck driver o Device ID : 0x352 o No. of Ports : 7 o CPU Port : 5 o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC o Setting Switch Port #6 connected to GMAC port for 1000 Full with FC gprtPhyIntEnable failed port 4 Switch driver init: o preset mode = Transparent o tag mode = No Tag port #0 establish switch connection libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 0 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI e1000: Copyright (c) 1999-2006 Intel Corporation. e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k e1000e: Copyright(c) 1999 - 2013 Intel Corporation. |
See also
- Linksys WRT32X
- Linksys WRT3200ACM
- Linksys WRT1900AC v1
- Linksys WRT1900AC v2
- Linksys WRT1900ACS
- Linksys WRT1200AC v1
- Linksys WRT1200AC v2
Images