Seagate Barracuda 7200.12 1TB, ST31000528AS (9SL154-578)
Seagate ST31000528AS 9SL154-578
Country of manuf.: China
Form factor: 3.5"
Interface: SATA III
Rotation speed: 7200 RPM
Controller: LSI unknown
FLA1: ? MB (Brand? Model?)
RAM1: 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (ESMT M13S64164A-5T)
Additional chips
Spindle motor controller;STMicroelectronics;Smooth 100536983;;1;
Vendor stated capacity: 1000 GB930.946 GiB <br />0.909 TiB <br />953,288.847 MiB <br />1,000,000 MB <br />999,595,805,529.08 B <br />
Usable capacity: ? GiB
"100535537 REV C" is etched onto the bottom layer of one of of these drives (specifically, the unit below S/N 6VPC4XZG).
Serial
Pinout
The serial header is located next to the SATA connector.
[ ] [GND] [TxD] [RxD] --------> to SATA, SATAPWR
Noted units + info derived from
Unit1 (9VP0WFEN, FW CC35)
• smartctl output |
---|
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-27-generic] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000528AS Serial Number: 9VP0WFEN LU WWN Device Id: 5 000c50 01534ca11 Firmware Version: CC35 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Apr 24 21:32:06 2013 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 196) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 1568695 3 Spin_Up_Time 0x0003 095 094 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3456 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 086 060 030 Pre-fail Always - 437868995 9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 10721 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1738 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 096 000 Old_age Always - 1950 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 062 046 045 Old_age Always - 38 (Min/Max 18/38) 194 Temperature_Celsius 0x0022 038 054 000 Old_age Always - 38 (0 9 0 0 0) 195 Hardware_ECC_Recovered 0x001a 036 026 000 Old_age Always - 1568695 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 278099132431568 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3799510873 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 283125300 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10621 - # 2 Extended offline Interrupted (host reset) 40% 426 - # 3 Short offline Completed without error 00% 424 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. |
Unit2 (5VP172JT, FW CC36)
• sudo hdparm -I /dev/sda |
---|
ATA device, with non-removable media Model Number: ST31000528AS Serial Number: 5VP172JT Firmware Revision: CC36 Transport: Serial Standards: Used: unknown (minor revision code 0x0029) Supported: 8 7 6 5 Likely used: 8 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 1953523055 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 953868 MBytes device size with M = 1000*1000: 1000203 MBytes (1000 GB) cache/buffer size = unknown Nominal Media Rotation Rate: 7200 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE Power-Up In Standby feature set SET_FEATURES required to spinup after power up SET_MAX security extension * Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) unknown 206[12] (vendor specific) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 162min for SECURITY ERASE UNIT. 162min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 5000c500184e376e NAA : 5 IEEE OUI : 000c50 Unique ID : 0184e376e Checksum: correct |
Unit3 (9VP74ESX, FW CC46)
Ctrl+L, HW info
New Skews Pharaoh 0F with VTPI,RAP16,Common Code 4 Product FamilyId: 3F, MemberId: 03 HDA SN: 9VP74ESX, RPM: 7201, Wedges: 120, Heads: 4, Lbas: 000074706DB0, PreampType: 71 03 PCBA SN: 00007041FQ85, Controller: YETIST_3_*/4_0(649B)(3-12-3-3), Channel: AGERE_COPPERHEAD_LITE, PowerAsic: MCKINLEY DESKTOP LITE Rev 91, BufferBytes: 2000000 Package Version: PH0G7B.CCD4.GZ019Y.CC46 , Package P/N: ---------, Package Builder ID: UM, Package Build Date: 06/11/2010, Package Build Time: 14:08:50, Package CFW Version: PH0G.CCD4.00269973.UM00, Package SFW1 Version: B76C, Package SFW2 Version: ----, Package SFW3 Version: ----, Package SFW4 Version: ---- Controller FW Rev: 06111408, CustomerRel: CC46, Changelist: 00269973, ProdType: PH0G.CCD4, Date: 06/11/2010, Time: 140850, UserId: 00385341 Servo FW Rev: B76C RAP FW Implementation Key: 10, Format Rev: 0001, Contents Rev: A2 07 03 03 Features: - Quadradic Equation AFH enabled - VBAR with adjustable zone boundaries enabled - Volume Based Sparing enabled - IOEDC enabled - IOECC enabled - DERP Read Retries enabled - LTTC-UDR2 disabled
Unit4 (6VPC4XZG, FW CC46)
This HDD is more or less dead.
Boot log
Rst 0x20M Servo Processor Is Reset. RW: Disc Ctlr Initialization Completed. ExecuteSpinRequest vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002 (P) SATA Reset SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002 PASSvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002WriteDCOInfo FAILED during Initialization RW: Error processing Performance Parameter File: 203C PASSvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002vYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvYvY SIM Error 1002
Ctrl+L, HW info
New Skews Pharaoh 0F with VTPI,RAP16,Common Code 4 Product FamilyId: 3F, MemberId: 03 HDA SN: 6VPC4XZG, RPM: 7201, Wedges: 120, Heads: 4, Lbas: 000074706DB0, PreampType: 71 03 PCBA SN: 0000M132AC46, Controller: YETIST_3_*/4_0(649B)(3-12-3-3), Channel: AGERE_COPPERHEAD_LITE, PowerAsic: MCKINLEY DESKTOP LITE Rev 91, BufferBytes: 2000000 Package Version: PH0G7B.CCD4.GZ0E9Y.CC46 , Package P/N: 100650568, Package Builder ID: P9, Package Build Date: 11/15/2010, Package Build Time: 15:06:12, Package CFW Version: PH0G.CCD4.00308328.P900, Package SFW1 Version: B770, Package SFW2 Version: ----, Package SFW3 Version: ----, Package SFW4 Version: ---- Controller FW Rev: 11151506, CustomerRel: CC46, Changelist: 00308328, ProdType: PH0G.CCD4, Date: 11/15/2010, Time: 150612, UserId: 00410638 Servo FW Rev: B770 RAP FW Implementation Key: 10, Format Rev: 0001, Contents Rev: A2 08 17 03 Features: - Quadradic Equation AFH enabled - VBAR with adjustable zone boundaries enabled - Volume Based Sparing enabled - IOEDC enabled - IOECC enabled - DERP Read Retries enabled - LTTC-UDR2 disabled
Diag. shell help output
The help / command info. is available in /C using the command Q.
• all |
---|
Online CR: Rev 0011.0000, Flash, Abort Online ESC: Rev 0011.0000, Flash, Abort Looping Command or Batch File Online ' ': Rev 0001.0000, Flash, Pause Output Online '.': Rev 0011.0000, Flash, Display Active Status Online '?': Rev 0011.0000, Flash, Display Diagnostic Buffer Information Online '`': Rev 0012.0001, Flash, Display Read/Write Statistics Online '$': Rev 0012.0002, Flash, Display Read/Write Statistics By Zone Online '{': Rev 0011.0000, Flash, Toggle EIB-Specific R/W Tracing Online ^D: Rev 0011.0000, Flash, Toggle R/W Tracing Online ^N: Rev 0011.0000, Flash, Toggle R/W Tracing Online ^W: Rev 0011.0000, Flash, Enable and Init RW Statistics Online ^O: Rev 0001.0000, Flash, Advance Servo Tracing State Online '!': Rev 0011.0000, Flash, Display Current Read Channel Settings Online '<': Rev 0011.0000, Flash, Decrement Read/Write Scope Sync Online '>': Rev 0011.0000, Flash, Increment Read/Write Scope Sync Online '~': Rev 0014.0000, Flash, Display Native Interface Command State Online ^A: Rev 0012.0000, Flash, Display Firmware Revision Online ^B: Rev 0012.0000, Flash, Get Thermistor Temperature Online ^C: Rev 0011.0000, Flash, Firmware Reset Online ^E: Rev 0011.0000, Flash, Display Native Interface Configuration Online ^F: Rev 0011.0001, Flash, Display Native Interface Read Cache Information Online ^I: Rev 0011.0000, Flash, Display Controller Registers Online ^K: Rev 0011.0000, Flash, Display DST Status Online ^L: Rev 0023.0000, Flash, Display Sign On Message Online ^P: Rev 0011.0000, Flash, Toggle Diag Idle Mode Online ^Q: Rev 0011.0000, Flash, Resume Interface Task Online ^R: Rev 0011.0000, Flash, Enable ASCII Online Serial Port Mode Online ^S: Rev 0011.0000, Flash, Pause Interface Task Online ^T: Rev 0011.0000, Flash, Enable ESLIP Serial Port Mode Online ^U: Rev 0011.0000, Overlay, Display Congen Online ^V: Rev 0011.0000, Overlay, Toggle Interface Command Echo Online ^X: Rev 0012.0000, Flash, Display Native Interface and Read/Write Command History Online ^Y: Rev 0011.0000, Flash, Display DST Status Online ^Z: Rev 0011.0000, Flash, Enable ASCII Diagnostic Serial Port Mode Online ^\: Rev 0011.0000, Flash, Toggle Debug Display Enable All Levels CR: Rev 0011.0000, Flash, Abort All Levels '/': Rev 0001.0000, Flash, Change Diagnostic Command Level, /[Level] All Levels '+': Rev 0012.0000, Flash, Peek Memory Byte, +[AddrHi],[AddrLo],[NotUsed],[NumBytes] All Levels '-': Rev 0012.0000, Flash, Peek Memory Word, -[AddrHi],[AddrLo],[NotUsed],[NumBytes] All Levels '=': Rev 0011.0002, Flash, Poke Memory Byte, =[AddrHi],[AddrLo],[Data],[Opts] All Levels '@': Rev 0001.0000, Overlay, Batch File Label, @[LabelNum] All Levels '|': Rev 0001.0000, Overlay, Batch File Terminator, | All Levels '*': Rev 0011.0000, Overlay, Special Batch File Function, *[FuncId],[FuncParm0],[FuncParm1] All Levels 'A': Rev 0011.0000, Overlay, Set Test Space, A[OptsOrParmSelect],[ParmValue],[AddrType],[HdForCylLimit] All Levels 'L': Rev 0001.0002, Overlay, Enable Looping, L[Opts],[CountOrStopOnErrCode] Level 1 'S': Rev 0011.0001, Flash, Edit Processor Memory Byte, S[AddrHi],[AddrLo],[MemValue],[NumBytes],[Opts] Level 1 'U': Rev 0011.0001, Flash, Edit Buffer Memory Byte, U[AddrHi],[AddrLo],[MemValue],[NumBytes] Level 1 'e': Rev 0011.0000, Flash, Spin Down and Reset Drive, e[MsecDelay],[Opts] Level 1 'm': Rev 0011.0001, Flash, Edit Processor Memory Word, m[AddrHi],[AddrLo],[MemValue],[NumBytes],[Opts] Level 1 'B': Rev 0011.0000, Overlay, Buffer Display, B[DisplayBlk],[RefBlk],[NumBlks],[Opts],[SymBits] Level 1 'D': Rev 0011.0001, Overlay, Memory Block Display, D[AddrHi],[AddrLo],[CompVal],[NumBytes],[Opts],[SizeInBytes] Level 1 'G': Rev 0011.0000, Overlay, Generic Read/Write Request, G[Parm0],[Parm1],[Parm2],...[Parm9] Level 1 'N': Rev 0015.0000, Overlay, SMART Control, N[SubCmd],[SubCmdParm0],[SubCmdParm1] Level 1 'c': Rev 0011.0000, Overlay, Buffer Compare, c[SrcBlk],[RefBlk],[NumBlks],[ContOnErr] Level 1 'j': Rev 0001.0000, Overlay, Display Hardware Jumper Setting, j[HardwareJumperSelect] Level 2 'J': Rev 0001.0000, Flash, Particle Sweep, J[ Start Cyl ],[ End Cyl ],[ Duration mSec ],[ Dwell mSec ],[ JIT mode ] Level 2 'U': Rev 0011.0000, Flash, Spin Up Drive, U[HoldState],[Hd],[Cyl] Level 2 'Z': Rev 0011.0000, Flash, Spin Down Drive, Z Level 2 'B': Rev 0011.0000, Overlay, Buffer Display, B[DisplayBlk],[RefBlk],[NumBlks],[Opts],[SymBits] Level 2 'C': Rev 0011.0000, Overlay, Buffer Copy, C[SrcBlk],[DestBlk],[NumBlks] Level 2 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level 2 'F': Rev 0011.0000, Overlay, Modify Track Defect List, F[PSctr/LBA],[Action] Level 2 'H': Rev 0011.0000, Overlay, Select Logical Head, H[Hd],[SkType],[Options] Level 2 'I': Rev 0012.0000, Overlay, Display / Modify Adaptive Parameter, I,[GroupId] Level 2 'K': Rev 0011.0000, Overlay, Set Tracking Offset, K[OffsetValue],[PersOrTempOpt],[UnitsOpt],[ChanReload] Level 2 'M': Rev 0012.0000, Overlay, Set Diag Idle Mode, M[ModeSelect],[ModeMask],[ResetToPowerOn] Level 2 'N': Rev 0001.0000, Overlay, Set Direct Write Mode, N[EnableDirWrtModeOpt] Level 2 'O': Rev 0011.0000, Overlay, Seek Repeatedly Between Physical Cylinders, O[StartPhyCyl0],[StartPhyCyl1],[NumSkPairs],[NumSeconds],[Hd] Level 2 'P': Rev 0011.0000, Overlay, Set Buffer Pattern, P[PatternSelOrPatternLow],[PatternHi],[PatternBits],[Opts],[BlkNum],[NumBlks] Level 2 'Q': Rev 0011.0000, Overlay, Write, Read, Read CHS, Q[Sec],[NumSecs],,[PhyOpt],[Opts] Level 2 'R': Rev 0011.0000, Overlay, Read CHS, R[Sec],[NumSecs],,[PhyOpt],[Opts] Level 2 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 2 'T': Rev 0014.0000, Overlay, Measure Throughput, T[Opts],[CylSkew],[HeadSkew],[MiniZoneSkew],[SkewStep],[LengthInTracks],[OffsetInTracks],[NumberOfRetries] Level 2 'V': Rev 0011.0000, Overlay, Read Verify CHS, V[Sec],[NumSecs],[CompareBlk],[Opts] Level 2 'W': Rev 0011.0000, Overlay, Write CHS, W[Sec],[NumSecs],,[PhyOpt],[Opts] Level 2 'X': Rev 0013.0000, Overlay, Display Track Information, X[LogCyl],[Hd],[SysAreaOpt],[Opts],[RowsPerPage] Level 2 'Y': Rev 0011.0000, Overlay, Set Retries - DERP, Y[Mode],[MaxRdRetries],[MaxWrtRetries],[OtcTLevel],[Options] Level 2 'a': Rev 0002.0000, Overlay, Measure Optimum Skew, a Level 2 'c': Rev 0011.0000, Overlay, Buffer Compare, c[SrcBlk],[RefBlk],[NumBlks],[ContOnErr] Level 2 'h': Rev 0013.0000, Overlay, Translate Physical Sector, h[Sec],[NumSecs] Level 2 'i': Rev 0011.0000, Overlay, Display Defects On Current Track, i Level 2 'j': Rev 0011.0000, Overlay, Read Wedge, j[WedgeAddr],[NumWedges],[NumSkipedWedges],[TranSize],[Opts],[RegAddr0],...,[RegAddr13] Level 2 'k': Rev 0001.0000, Overlay, Set User Cylinder/Head/MiniZone Skew, k[CylSkew],[HeadSkew],[MiniZoneSkew] Level 2 'l': Rev 0013.0000, Overlay, Translate Logical Sector, l[Sec],[NumSecs] Level 2 'o': Rev 0001.0000, Overlay, Corrupt LBA, o[Lba],[NumBlocks],[BurstSpan],[BurstOffset],[NumberOfRandomCorrupt],[Flags] Level 2 'r': Rev 0011.0000, Overlay, Read Long CHS or Read System CHS, r[LongSec],[LongSecsOrSysSec],[SysSecs],[LongPhySecOpt],[LongOpts],[SysOpts] Level 2 's': Rev 0011.0000, Overlay, Seek to Physical Cylinder and Head, s[Cyl],[Hd],[ValidKey],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 2 't': Rev 0013.0000, Overlay, Translate Wedge, t[Wdg],[NumWdgs] Level 2 'u': Rev 0011.0000, Overlay, Enable/Disable Channel/Preamp Register Display, u[EnableDisableOpt] Level 2 'v': Rev 0011.0000, Overlay, Convert Data Track Percentage To Servo Offset Count, v[Percentage] Level 2 'w': Rev 0011.0000, Overlay, Write Long CHS or Write System CHS, w[LongSec],[LongSecsOrSysSec],[SysSecs],[LongPhySecOpt],,[SysOpts] Level 2 'x': Rev 0014.0000, Overlay, Display Zone Information, x[Partition],[Hd],[Zone],[Options] Level 2 'y': Rev 0011.0000, Overlay, Set DERP Retry State, y[Type],[PathState],[RetryStateCnt],[LoopCnt1],[LoopCnt2] Level 2 'z': Rev 0011.0001, Overlay, Write Wedge, z[WedgeAddr],[NumWedges],[NumSkipedWedges],[TranSize],[Opt],[RegAddr0],...,[RegAddr13],[TSpacing] Level 2 '7': Rev 0011.0000, Overlay, Write Verify CHS, 7[Sec],[NumSecs],[WrBufBlk],[Opts] Level 3 'U': Rev 0011.0000, Flash, Spin Up Drive, U[HoldState],[Hd],[Cyl] Level 3 'V': Rev 0011.0000, Flash, Read or Write Power ASIC Register, V[RegAddr],[RegValue],[WrOpt] Level 3 'Z': Rev 0011.0000, Flash, Spin Down Drive, Z Level 3 'D': Rev 0011.0000, Overlay, Measure Seek Access Time, D[SkLength],[SkType],[NumSks] Level 3 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level 3 'H': Rev 0011.0000, Overlay, Select Logical Head, H[Hd],[SkType],[Options] Level 3 'O': Rev 0011.0000, Overlay, Seek Repeatedly Between Physical Cylinders, O[StartPhyCyl0],[StartPhyCyl1],[NumSkPairs],[NumSeconds],[Hd] Level 3 'Q': Rev 0011.0000, Overlay, Write, Read, Write, Read CHS, Q[Sec],[NumSecs],[Opts] Level 3 'R': Rev 0011.0000, Overlay, Read Current Servo Destination, R Level 3 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 3 'c': Rev 0001.0000, Overlay, Measure Latch Force, c[NumberOfSamples] Level 3 'f': Rev 0013.0000, Overlay, Real Time Servo Trace, f[SubCmd],[SubPrm0],[SubPrm1],[SubPrm2] Level 3 'p': Rev 0013.0000, Overlay, Translate Physical Sector, p[Sec],[NumSecs] Level 3 'q': Rev 0013.0000, Overlay, Translate Logical Sector, q[Sec],[NumSecs] Level 3 's': Rev 0011.0000, Overlay, Seek to Physical Cylinder and Head, s[Cyl],[Hd],[ValidKey],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 4 'B': Rev 0011.0000, Overlay, Enable / Disable RVFF, B[NewRvffControlMode] Level 4 'D': Rev 0011.0000, Overlay, Measure Seek Access Time, D[SkLength],[SkType],[NumSks] Level 4 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level 4 'H': Rev 0011.0000, Overlay, Select Logical Head, H[Hd],[SkType],[Options] Level 4 'K': Rev 0011.0000, Overlay, Set Tracking Offset, K[OffsetValue],[PersOrTempOpt],[UnitsOpt],[ChanReload] Level 4 'O': Rev 0011.0000, Overlay, Display Micro Jog for Logical Cylinder and Head, O[LogCyl],[Hd],[Opts],[SysAreaOpt] Level 4 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 4 'U': Rev 0011.0000, Overlay, Servo Batch Test sub commands, U[SubCmd],[SubCmdParm0],[SubCmdParm1],[SubCmdParm2] Level 4 'c': Rev 0001.0000, Overlay, Find Min Or Max Cylinders c[Head],[Mode],[RangeMultiplier],[RetryCountLimit],[FilterTimeConstant] Level 4 'd': Rev 0001.0000, Overlay, Display Servo Disc Slip Level 4 'e': Rev 0011.0000, Overlay, Enable / Disable PES Output, e[PesLeftShiftCnt],[DisablePesOut] Level 4 'g': Rev 0001.0000, Overlay, Display Servo Sector Error Log, g Level 4 'k': Rev 0001.0000, Overlay, Get VGA Data, k[OpType],[StartHt],[EndHt],[HtInc] Level 4 'l': Rev 0011.0000, Overlay, Scan Track for Servo Defects and ZAP, l[RdPositionOpt] Level 4 'q': Rev 0001.0000, Overlay, Display Servo Event Log, q Level 4 's': Rev 0001.0000, Overlay, Display Servo Sector Error Count, s Level 4 't': Rev 0011.0000, Overlay, Display / Modify ZAP Table, t[EntryNum],[EntryValue] Level 4 'u': Rev 0011.0000, Overlay, Set Seek Speed, u[Opts],[SkSpeed] Level 4 'v': Rev 0011.0000, Overlay, Butterfly Seek Test, v[StartPhyCyl0],[StartPhyCyl1],[NumSkPairs],[NumSeconds],[Hd] Level 5 'S': Rev 0011.0000, Flash, Enter Servo Matlab Shell, S Level 5 'B': Rev 0011.0000, Overlay, Servo Bode Plot, B[BodeType],[InjAmp],[Fmin],[Fmax],[NumFreq],[NumSamples],[EnableTracing] Level 5 'C': Rev 0011.0000, Overlay, Generic Servo Command, C[CmdNum],[Parm1],...[Parm7] Level 5 'D': Rev 0011.0000, Overlay, Read / Unlock DDR Buffer, B[OperateCode] Level 5 'E': Rev 0001.0000, Overlay, Measure Disc Eccentricity Level 5 'G': Rev 0011.0000, Overlay, Select Servo Controller, G[Head],[Controller],[InputShift] Level 5 'K': Rev 0001.0000, Overlay, Servo Disc Slip, K [OperationSelectId] Level 5 'R': Rev 0011.0000, Overlay, Read Servo RAM at Address, R[Addr],[NumBytes] Level 5 'U': Rev 0011.0000, Overlay, Enable / Disable Servo Updates, U[VcmDacUpdateOpt],[AToDUdateOpt] Level 5 'W': Rev 0011.0000, Overlay, Write Servo RAM at Address, W[Addr],[NumBytes],[Data] Level 5 'Z': Rev 0011.0000, Overlay, Read Zap from Disc to Table, Z Level 5 'd': Rev 0011.0000, Overlay, Disable / Enable Servo ZAP coefficients and ZAP read, d[ZapControlMode] Level 5 'e': Rev 0001.0000, Overlay, Enable / Disable Shock Sensor, e[Operation] Level 5 'i': Rev 0011.0000, Overlay, Read Servo Symbol Table at Index, i[Index] Level 5 'r': Rev 0011.0000, Overlay, Read Servo RAM at Index, r[Index],[NumBytes],[ByteOffset] Level 5 'w': Rev 0011.0000, Overlay, Write Servo RAM at Index, w[Index],[NumBytes],[Data],[ByteOffset] Level 6 'B': Rev 0011.0000, Overlay, Run Batch File, B[BatchFileNum],[DisplayOpt] Level 6 'D': Rev 0011.0000, Overlay, Display Batch File, D[BatchFileNum] Level 6 'E': Rev 0011.0000, Overlay, Enter Batch File, E[BatchFileNum] Level 7 'Z': Rev 0011.0000, Flash, Spin Down Drive, Z Level 7 's': Rev 0011.0000, Flash, Write Peripheral Register - channel or preamp, s[OpType],[RegAddr],[RegValue],[RegMask],[RegPagAddr] Level 7 't': Rev 0012.0000, Flash, Read Peripheral Register - channel or preamp, t[OpType],[RegAddr],[NumRegs],[RegMask],[RegPagAddr] Level 7 'B': Rev 0011.0000, Overlay, Buffer Display, B[DisplayBlk],[RefBlk],[NumBlks],[Opts],[SymBits] Level 7 'C': Rev 0011.0000, Overlay, Buffer Copy, C[SrcBlk],[DestBlk],[NumBlks] Level 7 'D': Rev 0012.0000, Overlay, Display Temperature, D,[DevSelect] Level 7 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level 7 'H': Rev 0011.0000, Overlay, Select Logical Head, H[Hd],[SkType],[Options] Level 7 'I': Rev 0012.0000, Overlay, Display / Modify Adaptive Parameter, I,[GroupId] Level 7 'K': Rev 0011.0000, Overlay, Set Track Format, K[UserAreaTrkFormatType],[SysAreaTrkFormatType] Level 7 'P': Rev 0011.0000, Overlay, Set Buffer Pattern, P[PatternSelOrPatternLow],[PatternHi],[PatternBits],[Opts],[BlkNum],[NumBlks] Level 7 'Q': Rev 0011.0000, Overlay, Write, Read, Read CHS, Q[Sec],[NumSecs],,[PhyOpt],[Opts] Level 7 'R': Rev 0011.0000, Overlay, Read CHS, R[Sec],[NumSecs],,[PhyOpt],[Opts] Level 7 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 7 'U': Rev 0011.0001, Overlay, Channel Temperature Adjust, U[TweakTemperature],[Partition],[Hd],[Zone],[Opts] Level 7 'W': Rev 0011.0000, Overlay, Write CHS, W[Sec],[NumSecs],,[PhyOpt],[Opts] Level 7 'X': Rev 0011.0000, Overlay, Display Preamp Head Resistance Level 7 'Y': Rev 0011.0000, Overlay, Set Retries - DERP, Y[Mode],[MaxRdRetries],[MaxWrtRetries],[OtcTLevel],[Options] Level 7 'b': Rev 0011.0000, Overlay, Erase Track, b[AdjacentTrkCnt],[EraseCntPerTrk],[AcEraseOpt] Level 7 'c': Rev 0011.0000, Overlay, Off Track Capability, c[Sec],[NumSecs],[SecIncrement],[Offset] Level 7 'h': Rev 0011.0001, Overlay, Mark Media Flaw, h[PhyCyl],[Hd],[PhySec],[UndisturbedRadius],[EraseBandTrks],[PtrLen],[WgSpec],[Od/Id] Level 7 'i': Rev 0011.0000, Overlay, Generic Read/Write Request, i[Parm0],[Parm1],[Parm2],...[Parm9] Level 7 'm': Rev 8004.0000, Overlay, Display Single Track Directed Offline Scan Information, m[clr,min scn] Level 7 'r': Rev 0011.0000, Overlay, Read Non-Volatile Adaptive Parameters, r[Opts] Level 7 'u': Rev 0011.0000, Overlay, Enable/Disable Write Fault, u[Op] Level 7 'w': Rev 0011.0000, Overlay, Save Adaptives To Flash, w[Seg],,22 Level 7 'x': Rev 0014.0000, Overlay, Display Zone Information, x[Partition],[Hd],[Zone],[Options] Level 7 'y': Rev 0011.0000, Overlay, Set DERP Retry State, y[Type],[PathState],[RetryStateCnt],[LoopCnt1],[LoopCnt2] Level 8 'U': Rev 0011.0000, Flash, Spin Up Drive, U[HoldState],[Hd],[Cyl] Level 8 'Z': Rev 0011.0000, Flash, Spin Down Drive, Z Level 8 'C': Rev 0011.0000, Overlay, Servo Diag Sub Cmds, C[SubCmd],[Parm0],[Parm1],[Parm2] Level 8 'R': Rev 0011.0000, Overlay, Read Current Servo Destination, R Level 8 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level 8 'd': Rev 0001.0000, Overlay, Head Smash Test, d[HeadDirection],[AccelerationDuration],[DecelerationDuration],[AccelerationCurrent],[DecelerationCurrent] Level A 'C': Rev 0013.0000, Overlay, Translate PBA, C[PbaHi],[PbaLow],[NumPbas] Level A 'D': Rev 0013.0000, Overlay, Translate Symbols From Index, D[PhyCyl],[Hd],[Sfi],[NumSfis] Level A 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level A 'F': Rev 0013.0000, Overlay, Translate LBA, F[LbaHi],[LbaLo],[SysAreaOpt],[NumLbas] Level A 'M': Rev 0011.0000, Overlay, Set Controller Test Port, M[Port],[Value] Level A 'P': Rev 0012.0000, Overlay, Merge Alt List into Slip List, P Level A 'Q': Rev 0011.0000, Overlay, Write, Read, Read LBA, Q[Lba],[NumLbas],[Opts] Level A 'R': Rev 0011.0000, Overlay, Read LBA, R[Lba],[NumLbas],,[Opts] Level A 'S': Rev 0011.0000, Overlay, Seek to LBA, S[LbaHi],[LbaLo],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level A 'W': Rev 0011.0000, Overlay, Write LBA, W[Lba],[NumLbas],,[Opts] Level A 'Y': Rev 0011.0000, Overlay, Set Retries - DERP, Y[Mode],[MaxRdRetries],[MaxWrtRetries],[OtcTLevel],[Options] Level A 'c': Rev 0013.0000, Overlay, Translate Logical Cylinder, Logical Head and Logical Sector, c[Cyl],[Hd],[Sec],[SysAreaOpt],[NumSecs] Level A 'd': Rev 0013.0000, Overlay, Translate Physical Cylinder, Logical Head and Physical Sector, d[Cyl],[Hd],[Sec],[NumSecs] Level A 'e': Rev 0013.0000, Overlay, Translate Nominal Cylinder and Logical Head, e[Cyl],[Hd],[Sec],[SysAreaOpt] Level A 'f': Rev 0013.0000, Overlay, Translate Physical Cylinder, Logical Head and Physical Wedge, f[Cyl],[Hd],[Wdg],[NumWdgs] Level A 'l': Rev 0013.0000, Overlay, Display Track Information, l[LogCyl],[Hd],[SysAreaOpt],[Opts],[RowsPerPage] Level A 'r': Rev 0001.0000, Overlay, Read CHS ( with EDAC/Format Options), r[Cyl],[Hd],[Sct],[Len],[EDACOff],[Seed],[Skew],[OverrideCyl],[OverrideHd] Level A 'w': Rev 0001.0000, Overlay, Write CHS ( with EDAC/Format Options), w[Cyl],[Hd],[Sct],[Len],,[Seed],[Skew],[OverrideCyl],[OverrideHd] Level A 'y': Rev 0011.0000, Overlay, Set DERP Retry State, y[Type],[PathState],[RetryStateCnt],[LoopCnt1],[LoopCnt2] Level C 'Q': Rev 0001.0000, Overlay, Display ASCII Command Information, Q[CmdLevel],[Cmd] Level C 'T': Rev 0011.0000, Overlay, Goop Plot, T[Hd],[StartTrk],[EndTrk],[ECCLvl],[NoFrcSync],[SkipCnt] Level E 'B': Rev 0011.0001, Overlay, Write Wedge, B[WedgeAddr],[NumWedges],[NumSkipedWedges],[TranSize],[Opt],[RegAddr0],...,[RegAddr13],[TSpacing] Level E 'C': Rev 0011.0000, Overlay, Read Wedge, C[WedgeAddr],[NumWedges],[NumSkipedWedges],[TranSize],[Opts],[RegAddr0],...,[RegAddr13] Level E 'G': Rev 0001.0000, Overlay, HeadDegradation, G[OperationControlOptions],[MeasurementControlOptions] Level E 'd': Rev 0001.0000, Overlay, SQMS Dibit Optimization, d[OptiAlgorithm],[LATE01 NOMR/F],[SweepStartVal],[SweepEndVal],[IterationCnt],[Verbose] Level E 'm': Rev 0011.0000, Overlay, Fast MSESER Measurement, m[] Level E 'n': Rev 0001.0000, Overlay, Dibit Extraction, n[sctr],[cnt],[dibit],[dibit],[dibit],[skip],[trim],[dsply] Level E 'o': Rev 0011.0000, Overlay, Fine RW Offset Measurement, o[NumAvgs],[TrkStepSize],[NumGuardTrks] Level E 'w': Rev 0011.0001, Overlay, Slow Write CHS, w[Sec],[NumSecs],[ConSec],[Skip],[UnitOfSkip] Level F 'U': Rev 0011.0000, Flash, Spin Up Drive, U[HoldState],[Hd],[Cyl] Level F 'Z': Rev 0011.0000, Flash, Spin Down Drive, Z Level F 'b': Rev 0011.0000, Flash, Set Baud Rate, b[BaudRate],[MsecDelay] Level F 't': Rev 0011.0000, Flash, Write Peripheral Register - channel or preamp, t[OpType],[RegAddr],[RegValue],[RegMask],[RegPagAddr] Level F 'B': Rev 0011.0000, Overlay, Buffer Display, B[DisplayBlk],[RefBlk],[NumBlks],[Opts],[SymBits] Level F 'C': Rev 0011.0000, Overlay, Buffer Copy, C[SrcBlk],[DestBlk],[NumBlks] Level F 'D': Rev 0011.0001, Overlay, Memory Block Display, D[AddrHi],[AddrLo],[CompVal],[NumBytes],[Opts],[SizeInBytes] Level F 'E': Rev 0001.0000, Overlay, Symbol Error Map, E[trk],[hd],[srt sctr],[sctr cnt],[action],[mx err] Level F 'P': Rev 0011.0000, Overlay, Set Buffer Pattern, P[PatternSelOrPatternLow],[PatternHi],[PatternBits],[Opts],[BlkNum],[NumBlks] Level F 'V': Rev 0011.0000, Overlay, Buffer Compare, V[SrcBlk],[RefBlk],[NumBlks],[ContOnErr] Level F 'Y': Rev 0011.0000, Overlay, Set Retries - DERP, Y[Mode],[MaxRdRetries],[MaxWrtRetries],[OtcTLevel],[Options] Level F 'r': Rev 0011.0000, Overlay, Read System CHS, r[LogSec],[NumSecs],[Opts] Level F 's': Rev 0011.0000, Overlay, Seek to Physical Cylinder and Head, s[Cyl],[Hd],[ValidKey],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level F 'y': Rev 0011.0000, Overlay, Set DERP Retry State, y[Type],[PathState],[RetryStateCnt],[LoopCnt1],[LoopCnt2] Level F 'z': Rev 0011.0000, Overlay, SataDebug, z[SubCmd],[Parm1],[Parm2],[Parm3] Level G 'B': Rev 0011.0000, Overlay, Fill Correction Buffer, B[StartAddr],[EndAddr],[Pattern],[Opts] Level G 'C': Rev 0011.0000, Overlay, Copy Correction Buffer, C[SrcAddr],[DestAddr],[NumSyms] Level G 'D': Rev 0011.0000, Overlay, Display Correction Buffer, D[StartAddr],[EndAddr],[CompareData] Level G 'F': Rev 0011.0000, Overlay, Fill Super Parity RAM, F[StartAddr],[EndAddr],[Pattern] Level G 'G': Rev 0011.0000, Overlay, Display Super Parity RAM, G[StartAddr],[EndAddr] Level H 'B': Rev 0011.0000, Overlay, Buffer Display, B[DisplayBlk],[RefBlk],[NumBlks],[Opts],[SymBits] Level H 'D': Rev 0001.0000, Overlay, Field Adjust Fly Height, c[Flags],[NumCollectionsToAvg],[PctOfBpiLowFreq],[PctOfBpiHighFreq],[PctOfTgtClr],[CTFFR],[ATT2R],[VgaLowFreq],[VgaHighFreq],[StartHtr],[EndHtr],[HtrIncr],[StartPreHtr],[ContactDac],[NumPreHeatSects],[NumPreChanCollectHeatSects],[NumChanCollectHeatSects],[NumPostChanCollectHeatSects],[HscIntgLength],[ChannelPreheatRevs] Level H 'F': Rev 0002.0002, Overlay, Modulation Detection Contact Detect, F[Flags],[NumRevsToAvg],[PctOfBpi],[HscIntgLength],[PatternSelect],,[CTFFR],[ATT2R],[VGA],[StartHtr],[EndHtr],[HtrIncr],[StartPreHtr],[NumPreHeatSects],[NumPreChanCollectHeatSects],[NumChanCollectHeatSects],[NumPostChanCollectHeatSects],[CoarseSearchStartClr],[FineSearchStartClr],[ContactSearchLimitClr] Level H 'P': Rev 0011.0000, Overlay, Set Buffer Pattern, P[PatternSelOrPatternLow],[PatternHi],[PatternBits],[Opts],[BlkNum],[NumBlks] Level H 'S': Rev 0011.0000, Overlay, Seek to Logical Cylinder and Head, S[Cyl],[Hd],[Offset],[OffsetUnitsOpt],[SkType],[Options] Level H 'b': Rev 0013.0000, Overlay, Contact Detect, b[Flags],[Revs],[BaselineRevs],[StartWedge],[A],[B],[C],[D],[E],[StartHt],[HtInc], [FixedPESThresh],[FilterDelta],[RangeStart],[RangePts],[AdjThreshSigmaLimit],[VarContactThreshBackup] Level H 'c': Rev 0003.0000, Overlay, Calibrate Clearance Coefficients Adjustment, c[Flags],[NumRevsToAvg],[PctOfBpi],[PctOfTgtClr],[LowerHIWPLimit],[UpperHIWPLimit],[CTFFR],[ATT2R],[VGA],[StartHtr],[EndHtr],[HtrIncr],[StartPreHtr],[NumPreHeatSects],[NumPreChanCollectHeatSects],[NumChanCollectHeatSects],[NumPostChanCollectHeatSects],[HscIntgLength] Level L 'C': Rev 0011.0000, Overlay, Copy Log File, C[SrcLog],[DestLog],[AppendOpt] Level L 'D': Rev 0013.0000, Overlay, Display Log File, D[Log],[ErrCode] Level L 'E': Rev 0011.0001, Overlay, Enable / Disable Logging, E[ErrLoggingOpt],[AsciiLoggingOpt],[RwStatsLoggingOpt] Level L 'I': Rev 0011.0000, Overlay, Display Log FileInfo, I[Log] Level L 'c': Rev 0011.0000, Overlay, Create Log File, c[Log],[LogType],[BufferOrDiskOpt],[NumBytes] Level L 'd': Rev 0011.0000, Overlay, Delete Log File, d[Log] Level L 'i': Rev 0011.0000, Overlay, Initialize Log File, i[Log] Level M 's': Rev 0001.0000, Overlay, Serial Port Test Results, s[Sub-command],[SptIndex],[ValidKey] Level T 'B': Rev 0011.0000, Flash, Set Baud Rate, B[BaudRate],[MsecDelay] Level T 'm': Rev 0013.0035, Flash, Format Partition, m[Partition],[FormatOpts],[DefectListOpts],[MaxWrRetryCnt],[MaxRdRetryCnt],[MaxEccTLevel],[MaxCertifyTrkRewrites],[ValidKey],[DataPattern] Level T 'E': Rev 0013.0000, Overlay, Display / Edit Log, E[LogNum],[ErrCodeOrSpecialFuncKey],[SpecialFunc] Level T 'F': Rev 0011.0000, Overlay, Display / Modify Congen, F[ValueRef],[Data],[ResetEnable] Level T 'J': Rev 0011.0001, Overlay, Display / Modify CAP, J[ParmValue],[ParmId],[ParmArrayBytes],[ParmByteArrayOffset] Level T 'O': Rev 0001.0000, Overlay, Select Data Output Mode, O[Mode],[VerboseOpts] Level T 'P': Rev 0011.0000, Overlay, Download Generic File, P[FileBytes] Level T 'R': Rev 0011.0000, Overlay, Read Non-Volatile Adaptive Parameters, R[Opts] Level T 'T': Rev 0011.0000, Overlay, Odd Even Encroachment Test, T[strt tk],[end tk],[hd],[rtry thrshld][ECC thrshld Level T 'V': Rev 0016.0000, Overlay, Display Defect Lists, V[ListMask],[Hd],[StartCyl],[NumCyls],[Summary],[FlagsMask] Level T 'W': Rev 0011.0000, Overlay, Save Adaptives To Flash, W[Seg],,22 Level T 'i': Rev 0011.0002, Overlay, Initialize Defect List, i[DefectListSelect],[SaveListOpt],[ValidKey] Level T 'r': Rev 0001.0000, Overlay, Read File, r[FileId],[VolumeNum],[CopyNum],[ByteOffset],[Length],[OutputFmt] Level T 'w': Rev 0001.0000, Overlay, Write File, w[FileId],[VolumeNum],[CopyNum],[ByteOffset] Level T '[': Rev 0011.0000, Overlay, ASCII Log Control, [[LogFunction],[Log] |