USB 2.0
Connector: Male A
Form factor tags: dongle
FCC ID: TE7WDN3200
IC ID: 8853A-WDN3200
PCB ID: 1108012300-1.0
For a list of all currently documented Ralink chipsets with specifications, see Ralink.
N600 Wireless Dual Band USB Adapter
- Product page • Driver
"1108012300-1.0" and "Rev:1.0sp1" is silkscreened on the board in the FCC photos.
- There is only one ID in the driver (148f:5572 / USB\VID_148F&PID_5572).
The device may (possibly) be known as the TL-WDN3321 in Asian markets.
- Indicated required USB power: 450 mA
Wi-Fi Certified : WFA15926 (as of 07/12/2012)
- On Product Version 1.2, Chip: Ralink RT5572N (datecode 1424), kernel 13.3:
dmesg
[18688.329911] usb 1-1.2: new high-speed USB device number 7 using ehci-pci
[18688.438319] usb 1-1.2: New USB device found, idVendor=148f, idProduct=5572
[18688.438326] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18688.438331] usb 1-1.2: Product: 802.11 n WLAN
[18688.438334] usb 1-1.2: Manufacturer: Ralink
[18688.438337] usb 1-1.2: SerialNumber: 1.0
[18688.545636] usb 1-1.2: reset high-speed USB device number 7 using ehci-pci
[18688.646725] ieee80211 phy2: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[18688.675286] ieee80211 phy2: rt2x00_set_rf: Info - RF chipset 000f detected
[18688.676016] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[18688.676515] usbcore: registered new interface driver rt2800usb
[18688.709514] systemd-udevd[6670]: renamed network interface wlan1 to wlan14
[18688.715588] ieee80211 phy2: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[18688.715820] ieee80211 phy2: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
Expand • iw list • >>
|
Wiphy phy2
Band 1:
Capabilities: 0x2f2
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 2-streams
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-15, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS)
* 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS)
* 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Capabilities: 0x2f2
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 2-streams
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-15, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 5180 MHz [36] (20.0 dBm) (passive scanning, no IBSS)
* 5190 MHz [38] (20.0 dBm) (passive scanning, no IBSS)
* 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS)
* 5210 MHz [42] (20.0 dBm) (passive scanning, no IBSS)
* 5220 MHz [44] (20.0 dBm)
* 5230 MHz [46] (20.0 dBm) (passive scanning, no IBSS)
* 5240 MHz [48] (20.0 dBm) (passive scanning, no IBSS)
* 5250 MHz [50] (disabled)
* 5260 MHz [52] (disabled)
* 5270 MHz [54] (disabled)
* 5280 MHz [56] (disabled)
* 5290 MHz [58] (disabled)
* 5300 MHz [60] (disabled)
* 5310 MHz [62] (disabled)
* 5320 MHz [64] (disabled)
* 5500 MHz [100] (disabled)
* 5510 MHz [102] (disabled)
* 5520 MHz [104] (disabled)
* 5530 MHz [106] (disabled)
* 5540 MHz [108] (disabled)
* 5550 MHz [110] (disabled)
* 5560 MHz [112] (disabled)
* 5570 MHz [114] (disabled)
* 5580 MHz [116] (disabled)
* 5590 MHz [118] (disabled)
* 5600 MHz [120] (disabled)
* 5610 MHz [122] (disabled)
* 5620 MHz [124] (disabled)
* 5630 MHz [126] (disabled)
* 5640 MHz [128] (disabled)
* 5650 MHz [130] (disabled)
* 5660 MHz [132] (disabled)
* 5670 MHz [134] (disabled)
* 5680 MHz [136] (disabled)
* 5690 MHz [138] (disabled)
* 5700 MHz [140] (disabled)
* 5745 MHz [149] (20.0 dBm) (passive scanning, no IBSS)
* 5755 MHz [151] (20.0 dBm) (passive scanning, no IBSS)
* 5765 MHz [153] (20.0 dBm) (passive scanning, no IBSS)
* 5775 MHz [155] (20.0 dBm) (passive scanning, no IBSS)
* 5785 MHz [157] (20.0 dBm) (passive scanning, no IBSS)
* 5795 MHz [159] (20.0 dBm) (passive scanning, no IBSS)
* 5805 MHz [161] (20.0 dBm) (passive scanning, no IBSS)
* 5825 MHz [165] (20.0 dBm) (passive scanning, no IBSS)
* 4920 MHz [-16] (disabled)
* 4940 MHz [-12] (disabled)
* 4960 MHz [-8] (disabled)
* 4980 MHz [-4] (disabled)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ AP, mesh point } <= 8,
total <= 8, #channels <= 1
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* action
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* Unknown command (84)
* Unknown command (87)
* Unknown command (85)
* Unknown command (89)
* Unknown command (92)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* Unknown mode (10): 0x40 0xd0
Device supports RSN-IBSS.
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
|
Expand • lsusb -vv -n 148f:5572 • >>
|
Bus 001 Device 008: ID 148f:5572 Ralink Technology, Corp. RT5572 Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x148f Ralink Technology, Corp.
idProduct 0x5572 RT5572 Wireless Adapter
bcdDevice 1.01
iManufacturer 1 Ralink
iProduct 2 802.11 n WLAN
iSerial 3 1.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 53
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 5
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
|
Images