ZyXEL Keenetic 4G III rev B

ZyXEL Keenetic 4G III rev B
Availability: EoL

Manuf (OEM/ODM): TP-LINK

(Est.) release date: March 2016
Country of manuf.: China
S/N prefix: EMG1301-T10A
Series: N300

Type: wireless router

FCC ID: none available
PCB ID: 2050500710

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: MediaTek MT7628NN (575 MHz)
FLA1: 16 MiB16,777,216 B 131,072 Kib 16,384 KiB 128 Mib 0.0156 GiB  (Winbond W25Q128BV)
RAM1: 64 MiB67,108,864 B 524,288 Kib 65,536 KiB 512 Mib 0.0625 GiB  (Winbond W9751G6KB-25)

Expansion IFs: USB 2.0
USB ports: 1
Serial: yes, 4-pin header, J13

WI1 chip1: MediaTek MT7628NN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: soldered

ETH chip1: MediaTek MT7628NN
Switch: MediaTek MT7628NN
LAN speed: 100M
LAN ports: 1
WAN speed: 100M
WAN ports: 1

bgn

Stock bootloader: U-Boot 1.1.3 Ralink v4.0.0.3 NDMS

Stock FW OS: Linux NDMS 2.16

TPFirmware supported: OpenWrt • (List | Dev | DLs)

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1310 additional devices
of which 98 are ZyXEL devices
Default login user: admin
Default login password: 1234
admin:1234 credentials used by 188 additional devices
of which 67 are ZyXEL devices

802dot11 OUI: 1C:74:0D (4 E, 4 W)
Ethernet OUI: 1C:74:0D (4 E, 4 W)

	CPU1 brand	WI1 chip1 brand
Keenetic 4G (KN-1210)	MediaTek	MediaTek
ZyXEL Keenetic 4G II	Ralink	Ralink
ZyXEL Keenetic 4G III rev B	MediaTek	MediaTek
ZyXEL Keenetic 4G rev B	Ralink	Ralink

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

N300 Wireless 3G/4G Router

Product page

ZyXEL Keenetic 4G III on ComPress (RU)

Reviews

OpenWrt for ZyXEL Keenetic 4G III rev.B (RU)

Serial

Expand • Start U-Boot with OpenWrt 19.07.1 • >>

U-Boot 1.1.3 [4.0.0.3-30] (May 31 2017 - 15:07:28)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb0000
MediaTek SPI BBU flash driver, SPI clock: 31MHz
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
============================================
Ralink UBoot Version: 4.0.0.3_NDMS
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:May 31 2017  Time:15:07:28
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size = 64 Mbytes
 Firmware test register status: 0x00000000

Resetting MT7628 PHY...
Dual image:     on
Boot active:    1
Boot backup:    1
Boot fails:     0

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Enter boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
3
You choosed 3
0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.167
   Created:      2020-01-29  16:05:35 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1592885 Bytes =  1.5 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.167 (inflabz@PC) (gcc version 7.5.0 
   (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 Wed Jan 29 16:05:35 2020
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is ZyXEL Keenetic 4G III rev.B