Banana Pi BPI M2+

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

Banana Pi BPI M2 + (V1.2)

Manuf (OEM/ODM): SinoVoIP

(Est.) release date: 2016
Country of manuf.: China

Amazon image

ASIN
B071Y3S27S (Flag of the United States.svg, On Amazon, On CCC)
multiple revisions of this device, use caution

Type: single-board computer

Power: 5 VDC, 2 A
Connector type: barrel
Conn. measurements: 4.0 mm (OD), 1.7 mm (ID), 9.5 mm (LEN)

CPU1: Allwinner H3 (1.0 GHz, 4 cores)
FLA1: 8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (Samsung KLM8G1GETF-B041)
RAM1: 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (Samsung K4B4G16460-BCK0 × 2)

Expansion IFs: USB 2.0, HDMI
USB ports: 3
Serial: yes, 3-pin header, populated, 3.3V TTL, (115200 8N1)

WI1 module: AMPAK AP6212
WI1 module IF: SDIO (module)
WI1 chip1: Broadcom BCM43430
WI1 802dot11 protocols: bgn
WI1 MIMO config: 1x1:1
WI1 antenna connector: U.FL

ETH chip1: Allwinner H3
ETH chip2: Realtek RTL8211E
LAN speed: 1GbE
LAN ports: 1

abgn

Additional chips
1A, 1.5MHz Synchronous Step-Down Regulator;Silergy;SY8008B;;2;
2A, 1MHz Synchronous Step-Down Regulator; Silergy;SY8089;;1;
3A, 500KHz Synchronous Step Down Regulator;Silergy;SY8113B;;1;
5.5V, 2A Low Loss Power Distribution Switch;Silergy;SY6280;;1;
Microprocessor Supervisory Circuit;SGMicro;SGM803;;1;
300mA CMOS LDO Regulator;Diodes Inc;AP2127;;7;
Ultra Low Capacitance TVS Array;SemTech;RClamp0524P;;3;,

Stock bootloader: U-Boot

Stock FW OS: Bananian

TPFirmware supported: Android, Ubuntu, Debian, OpenWrt • (List | Dev | DLs)

Flags: MicroSD Card slot, Bluetooth 4.0, HDMI out, IrDA, GPIO, MIPI CSI

802dot11 OUI: none specified

For a list of all currently documented Allwinner SoC's with specifications, see Allwinner.
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.


Product page

Specifications

Banana Pi M2 Plus Board
  • CPU: Allwinner H3 Quad-core (ARM Cortex-A7) @1.0GHz
  • GPU: Mali-400 MP2 @600MHz, OpenGL ES 2.0, H.265/HEVC 4K
  • Memory: 1GB (DDR3) RAM (shared with GPU)
  • Flash: 8GB (eMMC) flash on-board
  • Network: 1x GbE (10/100/1000) Ethernet
  • WiFi/BT: AMPAK AP6212, BT 4.0, SDIO (option AP6181, AP6335)
  • Audio Outputs: HDMI; Video Input: A CSI input connector
  • Camera: Supports 8-bit YUV422 CMOS sensor interface,
Supports CCIR656 protocol for NTSC and PAL,
Supports SM pixel camera sensor,
Supports video capture solution up to 1080p@30fps
  • Video Outputs: Supports HDMI output with HDCP, CEC, 3D function,
Integrated CVBS, Supports simultaneous output of HDMI and CVBS
  • USB: 2x USB 2.0 (Host), 1x USB 2.0 (OTG) ports
  • GPIO: 40x Pins Header, compatible w/ Raspberry Pi B+
  • LED: Power Led & Status Led; IR: IR input on board
  • OS: Android, Ubuntu, Debian, Raspberry Pi Image, OpenWRT
  • Power: 5V/2A DC input can, but USB OTG input don’t supply power

See also